Baroness LM180C Owner's Operating Manual
  1. Manuals
  2. Brands
  3. Baroness Manuals
  4. Lawn Mower
  5. LM180C
  6. Owner's operating manual

Baroness LM180C Owner's Operating Manual

3-unit reel mower
Hide thumbs Also See for LM180C:
Table of Contents

Advertisement

Quick Links

Download this manual
3-Unit Reel Mower
Owner's Operating Manual
Serial No.
LM180C：20356-
"Required reading"
Read this manual before using the machine.
Original Instructions Ver.1.5

Advertisement

Table of Contents
loading

Related Manuals for Baroness LM180C

Summary of Contents for Baroness LM180C

  • Page 1 3-Unit Reel Mower Owner's Operating Manual Serial No. LM180C：20356- "Required reading" Read this manual before using the machine. Original Instructions Ver.1.5...
  • Page 2 LM180C Greeting Thank you for purchasing the Baroness product. This manual describes the proper handling, adjustment, and inspection of your product. We hope you will use the product safely, and take advantage of its best performance. Keeping the Owner's Operating Manual Keep this manual in the box on the right side of the seat.
  • Page 3 The operator is responsible for operating the product properly and safely. Maintenance should only be performed by a certified specialist. If you have any questions concerning maintenance or genuine parts, please contact a Baroness dealer or Kyoeisha. When making inquiries about the product, please specify the product's model designation and serial number.
  • Page 4 When replacing parts, be sure to use genuine Baroness parts or parts designated by Kyoeisha. Note that the Baroness product warranty may not apply to defects caused by the use of parts from other companies. Prior to use, carefully read the following manuals to thoroughly understand the contents for safe and correct operation.

  • Page 5: Table Of Contents

    LM180C Contents Safety .............. Page 1-1 Safe Operating Practices .......Page 1-2 Disposal ............Page 2-1 Recycle and Waste Disposal ......Page 2-2 Product Overview .......... Page 3-1 Specifications ..........Page 3-2 Names of Each Section ......... Page 3-3 Regulation Decals ..........Page 3-4 Safety Signs and Instruction Signs ....
  • Page 6 LM180C Contents...

  • Page 7: Safety

    LM180C Safety Safe Operating Practices ...... Page 1-2 Training ..........Page 1-2 Preparation ..........Page 1-2 Operation ..........Page 1-3 Maintenance and storage ...... Page 1-4 Page 1-1...

  • Page 8: Safe Operating Practices

    LM180C Safety Failure to adequately follow these safety Never allow children or people unfamiliar precautions may cause an accident resulting in with these instructions to use or service the injury or death. machine. Local regulations may restrict the age of the...
  • Page 9 LM180C Safety If fuel is spilled, do not attempt to start the Never drive the machine on a slope with engine but move the machine away from an angle of gradient that is greater than the area of spillage and avoid creating any...
  • Page 10 LM180C Safety When using any attachments, never direct Never store the equipment with fuel in the discharge of material toward bystanders nor tank inside a building where fumes may allow anyone near the machine while in reach an open flame or spark.

  • Page 11: Disposal

    LM180C Disposal Recycle and Waste Disposal ....Page 2-2 About Recycle ........Page 2-2 About Waste Disposal ......Page 2-2 Page 2-1...

  • Page 12: Recycle And Waste Disposal

    LM180C Disposal Recycle and Waste Disposal About Recycle Recycling battery etc. is recommended for environmental conservation and economical use of resources. It may be required by local laws. About Waste Disposal Make sure that waste generated when servicing or repairing the machine is disposed of in accordance with local regulations.

  • Page 13: Product Overview

    LM180C Product Overview Specifications ........Page 3-2 Specifications .........Page 3-2 Sound Pressure Level ......Page 3-3 Sound Power Level ....... Page 3-3 Vibration Level ........Page 3-3 Names of Each Section ......Page 3-3 Regulation Decals ........Page 3-4 Positions of Regulation Decals ....Page 3-4 Description of Regulation Decals ..

  • Page 14: Specifications

    LM180C Product Overview Specifications Specifications Type LM180C Total length 84.65 in 215 cm During 81.89 in 208 cm operation Total width Dimensions During 72.83 in 185 cm transport Steering Total height 40.16 in 102 cm wheel Total weight (empty fuel tank) 844.36 lb...

  • Page 15: Names Of Each Section

    LM180C Product Overview Sound Pressure Level Names of Each Section Sound Pressure Level This machine was confirmed to have a continuous A-weighted sound pressure level of 93dB by measuring identical machines in accordance with the procedure specified in ISO 5395-1:2013.

  • Page 16: Regulation Decals

    LM180C Product Overview Regulation Decals Specification Decal (For Europe) Positions of Regulation Decals The Specification decal indicates the CE marking, model , and weight, etc. quwxcl-234 Positions of Regulation Decals_001 kj8jic-001 Specification Decal_001 Serial number plate Specification Decal Noise Emission Decal...

  • Page 17: Safety Signs And Instruction Signs

    Part numbers for decals that need to be Flying objects - Be sure that people around replaced are listed in the parts catalog. the machine keep a safe distance away. Order them from a Baroness dealer or Kyoeisha. 　 Positions of Safety Decals and Instruction...
  • Page 18 LM180C Product Overview Caution to Mutilation Decal Caution to Rotating Object Decal K4205001600 K4205001530 DECAL, CAUTION TO MUTILATION Decal, caution to rotating object Warning Warning May cut your hand or leg - Stop the cutter Watch for rotating parts - Keep your hands rotation and engine.
  • Page 19 LM180C Product Overview Decal on Reading Owner's Operating Manual K4205001560 Decal, read Owner's Operating Manual Warning Read the Owner's Operating Manual. tpfrw8-001 Decal on Reading Owner's Operating Manual_001 Safety Signs and Instruction Signs Page 3-7...
  • Page 20 LM180C Product Overview Page 3-8 Safety Signs and Instruction Signs...

  • Page 21: Handling Instructions

    LM180C Handling Instructions Inspections ..........Page 4-2 Diff-lock Pedal ........Page 4-18 Parking Brake Lever ......Page 4-19 Reel Cutter (Cutting Cylinder) and Bed Knife (Bottom Blade) ...... Page 4-2 Travel of Machine ........ Page 4-19 Cover ............. Page 4-2 Moving the Machine ......Page 4-19 Roller .............

  • Page 22: Inspections

    LM180C Handling Instructions Cover Inspections Inspection of Covers Inspect the machine according to the maintenance schedule so that you will be able to Warning take advantage of its optimum performance for a long period of time. If you have removed the covers during...

  • Page 23: Air Cleaner

    LM180C Handling Instructions Follow the steps below to clean the air Air Cleaner cleaner. Inspection of Air Cleaner Before installing the element, clean it with white kerosene, immerse it in an The air cleaner is a component that removes admixture of three parts white kerosene...

  • Page 24: Tire

    LM180C Handling Instructions Tire Important A slacking or damaged belt may cause the Inspection of Tires cutter rotation speed or operation speed to be Check the pneumatic pressure of the tires. insufficient for operation. Make sure that there are no cracks, damage or abnormal wear on the tires.

  • Page 25: Engine Oil

    LM180C Handling Instructions Engine Oil Filling of Engine Oil Inspection of Engine Oil Important Do not fill too much engine oil. Otherwise, the Important engine may be damaged. Screw the oil level gauge firmly. Important Stop the engine, wait for 10 to 20 minutes for the engine to cool down, then check the Do not mix different types of engine oil.

  • Page 26: Fuel

    LM180C Handling Instructions Fuel Fuel Strainer Inspection of Fuel Supply Inspection of Fuel Strainer Observe the fuel gauge located on the fuel The fuel strainer is installed near the fuel tank tank to check the fuel level. and cleans the fuel that enters the carburetor.

  • Page 27: Transmission

    LM180C Handling Instructions Supply transmission oil through the oil filling Important port. During installation, prevent contamination with dirt or dust. If the fuel is contaminated with dirt, dust, etc., the fuel flow will become insufficient. Correctly install all parts in their original positions.

  • Page 28: Tightening Torques

    LM180C Handling Instructions Tightening Torques Important Refer to the Tightening Torque table. Note that the Baroness product warranty may not apply to defects caused by incorrect or overtorque tightening, etc. Standard Tightening Torques Bolts and Nuts Important A number of bolts are used in each part of this machine.
  • Page 29 LM180C Handling Instructions General bolt Strength classification 4.8 Nominal diameter tib3yb-001 kgf-cm lb-in 3 - 5 30.59 - 50.99 26.55 - 44.26 7 - 9 71.38 - 91.77 61.96 - 79.66 14 - 19 142.76 - 193.74 123.91 - 168.17 29 - 38 295.71 - 387.49...

  • Page 30: Principal Tightening Torques

    LM180C Handling Instructions Principal Tightening Torques Tightening Torque by Model LM180C Tighten the following bolts and nuts at the torque specified in the table. For thread locking adhesive, apply a mild to high-strength thread locker (ThreeBond 1322 or equivalent anaerobic sealant).

  • Page 31: Adjustment Before Work

    LM180C Handling Instructions Insert two or three strips of newspaper into Adjustment before Work the space between the reel cutter (cutting cylinder) and the bed knife (bottom blade) at Adjustment of Seat an angle of 90 degrees. Then, rotate the reel...

  • Page 32: Procedure To Start/Stop Engine

    LM180C Handling Instructions Make sure that the parking brake is applied. Adjustment of Cutting Height Make sure that the traveling clutch lever is set to the "OFF" position. Important Make sure that the reel rotation lever is set The front wheel is provided to prevent the reel to the "Stop"...

  • Page 33: Operation Method

    LM180C Handling Instructions Remove the ignition key. Leave the driver's seat. Safety Mechanisms This machine has the safety device for starting / stopping engine. As for starting the engine, the safety device prevents the engine from starting unless it meets each of the following three conditions.

  • Page 34: Description Of Operation Decals

    LM180C Handling Instructions Description of Operation Decals Change Plate Engine Switch Mark LM180A-0810Z0 Decal, change lever K4203000670 This indicates the positions of the change Decal, engine switch lever. This indicates the key switch positions. an8lyj-003 rcyo1p-010 Change Plate_001 Engine Switch Mark_001...

  • Page 35: Throttle Lever

    LM180C Handling Instructions Clutch Operation Mark Brake Mark Clutch operation mark K4209001200 This illustrates “Engage/Disengage" of the DECAL, BRAKE traveling clutch. It illustrates the locking position for the parking brake. 91a7z5-003 7elqr2-002 Clutch Operation Mark_001 Brake Mark_001 Traveling clutch "Engage"...

  • Page 36: Change Lever

    LM180C Handling Instructions Change Lever Traveling Clutch Lever Important Warning Do not change the lever position during Be careful of the machine suddenly traveling. Otherwise, the transmission may be accelerating when the machine starts to travel damaged. if the throttle lever is set to the "High speed"...

  • Page 37: Reel Rotation Lever

    LM180C Handling Instructions Reel Rotation Lever Mower Unit Lifting lever Left and Right Mower Units Caution Set the reel clutch lever to the engaged Caution position immediately before mowing. At all Before raising or lowering the mower units, other times, be sure to leave the reel clutch make sure that there are no people around lever in the disengaged position.

  • Page 38: Brake Pedal

    LM180C Handling Instructions Brake Pedal Rear Mower Unit The brake pedal is located in the right foot Important area. In order to stop the machine, depress the Before raising or lowering the mower units, brake pedal with your right foot until the pedal make sure that there are no people around hits the pedal stopper.

  • Page 39: Travel Of Machine

    LM180C Handling Instructions Parking Brake Lever Caution Make sure not to touch rotating tires with your Caution hands or legs. Never park the machine on a slope. Start the engine. "Procedure to Start Engine" (Page 4-12) Important Depress the brake pedal, and release the Be sure to release the parking brake before parking brake.

  • Page 40: Cutting Work

    LM180C Handling Instructions Cutting Work Cutting Operation Warning Do not start to move or stop the machine abruptly. Caution Cutting work must be performed at an appropriate speed for the site and location. When cutting bumpy surfaces, keep the engine rpm steady, and slow down the cutting speed.

  • Page 41: Maintenance

    LM180C Maintenance Maintenance Precautions ..... Page 5-2 Maintenance Schedule ......Page 5-3 Adjusted Values ........Page 5-4 Jacking Up The Machine .......Page 5-5 About Jacking Up The Machine .....Page 5-5 Jack-up Points ........Page 5-5 Greasing ..........Page 5-6 About Greasing ........Page 5-6 Greasing Points ........

  • Page 42: Maintenance Precautions

    Use tools appropriate for each maintenance operation. Important For the safe and best performance of your machine, use Baroness genuine parts for replacement and accessories. Please note that our product warranty may be void if you use non-genuine parts for replacement or accessories.

  • Page 43: Maintenance Schedule

    LM180C Maintenance Maintenance Schedule Follow the maintenance schedule below. ○・・・Inspect, adjust, supply, clean ●・・・Replace (first time) △・・・Replace Maintenance Item Remarks Tightening the parts ○ 　 　 　 　 　 　 　 　 　 　 　 　 　 　 Fuel ○ 　 　 　 　 　 　 　 　 　 　 　 　 　...

  • Page 44: Adjusted Values

    LM180C Maintenance Maintenance Item Remarks Oil leakage ○ 　 　 　 　 　 　 　 　 　 　 　 　 　 　 Transmission oil 50hrs (first time) ○ 　 　 　 ● 　 　 　 　 　 △ 　 　 　...

  • Page 45: Jacking Up The Machine

    LM180C Maintenance Jacking Up The Machine Jack-up Portion 　 Front axle, center About Jacking Up The Machine Front axle, right Front axle, left Warning Transmission case, lower When replacing a tire or beginning any other Transmission axle case, left maintenance or repairs, be sure to chock the Transmission axle case, right wheels to prevent the machine from moving.

  • Page 46: Greasing

    LM180C Maintenance Transmission case, lower Greasing Points Grease nipples are installed in the following locations. Add grease every 50 hours of operation. rwyt62-015 Jack-up Points_005 Transmission axle case, left rwyt62-016 Jack-up Points_006 Transmission axle case, right 8bq62b-454 Greasing Points_001 No. of 　...
  • Page 47 LM180C Maintenance Front wheels Mower frame There is one point each on the left and the There is one point each on the left and the right wheel. right mower units. 8bq62b-056 8bq62b-059 Greasing Points_002 Greasing Points_005 Front wheel front pin...
  • Page 48 LM180C Maintenance Handle tension Rear roller Supply automobile transmission gear oil #90 There is one point each on the left and the every 50 hours of operation. right of each unit. 8bq62b-062 8bq62b-066 Greasing Points_008 Greasing Points_012 Mower tension 8bq62b-063...

  • Page 49: Maintenance Work

    Strips of newspaper, Abrasive sealed parts of the reel shaft. (Avoid high- [Back lapping powder mixed with oil; or gel pressure water cleaning.) compound (Baroness genuine abrasive)], Otherwise, it may cause damage to the Brush, Socket (opposite side 27). machine.

  • Page 50: Sharpening Of Reel Cutter (Cutting Cylinder)

    (cutting For sharpening the reel cutter (cutting cylinder), then check it for sharpness. cylinder), contact your dealer or Baroness. Repeat steps 4 to 12 until the entire range If the outer diameter of the reel cutter (cutting...

  • Page 51: Replacement Of Reel Cutter (Cutting Cylinder)

    LM180C Maintenance Note: The outer diameter of the reel cutter (cutting cylinder) shaft is 25.4 mm (1.00 in). ok5ueg-007 Sharpening of Reel Cutter (Cutting Cylinder)_002 Reel cutter (cutting cylinder) blade Sharpening width for outer diameter of reel cutter (cutting cylinder)

  • Page 52: Replacement Of Bed Knife (Bottom Blade)

    LM180C Maintenance When the outer diameter of the reel cutter Replacement of Bed Knife (Bottom Blade) (cutting cylinder) is less than the usage limit Usage limit Caution Dimension B Dimension B Both the reel cutter (cutting cylinder) and the (Distance...

  • Page 53: Removing/Installing Tires

    LM180C Maintenance Place the tire jack beneath the jack-up point Removing/Installing Tires of the rear wheel transmission area securely, then raise it until the tire lifts off Front Tires the ground. Follow the steps below to remove the front "Jack-up Points" (Page 5-5) tires: Remove the bolts.
  • Page 54 LM180C Maintenance Belt Installation Locations Reel Rotation Lever Belts are installed in this machine at the Loosen the adjustment bolt, then change following locations. the length of the rod. Adjust the clearance between the rod- tension metal fitting and the collar to be 5 mm (0.20 in), when the reel rotation lever is...
  • Page 55 LM180C Maintenance Left and Right Mower Units Adjusting nut A Adjusting nut B Belts are always stretched at a constant tension by the springs. 10 mm (0.39 in) Loosen the adjustment bolt, then adjust the clearance between the collar and the Rear Mower Tension mower lifting arm to be 1 mm (0.04 in).

  • Page 56: Adjustment Of Parking Brake

    LM180C Maintenance Adjust the parking brake by the brake wire Rear Mower Unit adjustment bolt. Loosen adjusting nut A. While pressing the push button, return the parking brake lever to its resting position to Tighten adjusting nut B, then change the release the parking brake.

  • Page 57: Adjustment Of Brake

    LM180C Maintenance Make sure that the brake is not applied any Adjustment of Brake longer when you release the brake pedal. Caution If the brake is not applied effectively even if you depress the pedal up to the stopper, adjust the brake rod.

  • Page 58: Adjustment Of Diff-Lock Wire

    LM180C Maintenance Adjustment of Diff-lock Wire Adjustment of Mower Stopper Lower the left and right mower units, then Important engage the reel rotation lever. If the diff-lock seems ineffective when you Loosen the nut, then adjust the position of depress the diff-lock pedal, adjust the diff-lock the adjustment bolt so that the mower wire.

  • Page 59: Adjustment Of Wire To Hook Mower

    LM180C Maintenance Adjustment of Wire to Hook Mower Wire to hook the left / right mower Loosen the nuts and move the adjustment bolt toward the outside of the machine to increase the wire tension. Without gripping the lever, raise the right...

  • Page 60: Change Of Air Cleaner

    LM180C Maintenance Attach the drain plug to the engine. Change of Air Cleaner Remove the oil level gauge. A contaminated air cleaner element may cause Supply new engine oil through the oil filling malfunction of the engine. port. To maximize the life of the engine, replace the Engine oil quantity is approximately 1.2...

  • Page 61: Change Of Transmission Oil

    LM180C Maintenance Change of Transmission Oil Oil filling port Oil level plug Caution Drain plug Be careful with hot oil, which could cause Check underneath the machine for oil burns if it contacts your skin. leakage. Important When you change the transmission oil, be...
  • Page 62 LM180C Maintenance Page 5-22 Maintenance Work...
  • Page 66 1-26, Miyuki-cho, Toyokawa-city, Tel : +81 - 533 - 84 - 1390 Head Office Fax : +81 - 533 - 84 - 1220 Aichi-pref, 442-8530 JAPAN LM180C--UM--GBZ/20F-00-S.K E02[LM180_EU02]...

Table of Contents