Iremote Control Electronic Ignition System (Simple Version); A- Igniting The Appliance; B- Adjusting The Heat Setting; C- Extinguishing The Appliance Fully - Focus Drumfocus M-B-C User, Installation And Servicing Instructions

REMOTE CONTROL ELECTRONIC IGNITION
I
SYSTEM
(SIMPLE VERSION)

A- IGNITING THE APPLIANCE

The switch has to be in ON position.
Simultaneously press the OFF and
( ) buttons of the remote control
L
for ignition.
An acoustic signal indicates that the
start sequence has begun. The elec-
tronic system then checks that the
main gas is flowing and ignites the
main burner; this may take up to 20
seconds.
(NOTE: During start-up, override
knob must be in ON position.)

B- ADJUSTING THE HEAT SETTING

You are now able to use the remote control. To increase the flame, the
top button ( ) should be depressed. Pressing the lower button (
L
the hand-set will reduce the flame.
It is also possible to turn the main burner all the way down so that it
is effectively off, leaving only the pilot ignited.

C- EXTINGUISHING THE APPLIANCE FULLY

From any heat setting, press the OFF button for a few seconds. This
will cause the burner to fully extinguish.
The system has a safety interlock which will not allow the Ignition
until the Interlock rests (this may take a few minutes).
D- MANUAL OVERRIDE (ACCORDING TO VERSION)
The switch must be in ON position.
The system has a Manual Override feature that allows manual opera-
tion without battery power. For manual operation, turn the override
knob to the MAN position. There is an opening that allows access to
the magnet stem, this should be pushed in to allow gas to pass to the
pilot. This stem must be held in whilst the Piezo igniter is depressed to
spark the Pilot. The stem must be held in for a further 15 seconds until
the pilot light establishes. If the Pilot does not hold when the stem is
released, repeat the process.
"ON-OFF" SWITCH
PIEZO IGNITER
(ACCORDING TO VERSION)
OVERRIDE KNOB
MAGNET STEM
When the pilot is established, the "Override" Knob may be turned to
the ON position. Control of the gas is then possible using the second
28 control.
To turn the appliance off using the manuel over-ride, flip the ON-OFF
switch.
REMOTE CONTROL ELECTRONIC IGNITION
I
SYSTEM

(FULL AUTOMATIC VERSION)

A- SETTING THE CURRENT TIME

After connecting the battery or by simultaneously pressing (
( ), the display flashes. You are in set mode. From set mode press (
M
to set hours and ( ) to set the minutes.
M
Wait or press OFF to return to manual mode.
B- SETTING THE DISPLAY (°C/24h - °F/12h)
Press OFF and ( ) to switch from °F (and 12h clock) to °C
M
(and 24h clock) display or vice versa.

C- CHANGING RUNNING MODE

Press briefly SET, running modes change in the following order :
) on
M
)
MAN TEMP
3TEMP
• Manual mode for flame height adjustment (MAN in display)
The mode MAN could be selected by pressing (
turn on the fire (main burner) or to increase flame height. Press (
to turn down to pilot. The 'send' symbol appears. The receiver confirms
the transmission by a sonorous signal.
• The mode 'day' temperature (
The sensor in the transmitter measures the room temperature.
The controller compares the room temperature with the set tempera-
ture and sends a signal to the receiver to turn the gas valve motor,
which adjusts the flame height accordingly.
• The 'night' temperature mode (
As above, there is an adjustment to control the 'night' temperature.
In this mode, the room temperature is compared to the 'night' tempe-
rature set. There is a differential temperature more important during
this cycle (less consumption).

D- TIMER

The timer mode (TIMER), as the temperature mode above, has a func-
tion of temperature control (
adjust the starting and ending time (there are 2 cycles of starting and
2 cycles of ending by 24h period).
)
If the temperature
TEMP
stand by until the next starting cycle. The set temperature displays
every 30 s.
E- ADJUST THE DESIRED TEMPERATURE
Select the desired running mode (
the SET button. .
Maintain the set button pressed until the display flashes. Adjust the
set temperature with (
Wait or press OFF to pass in temperature control mode.
If the control of temperature in night period must be switched off
(economic battery consumption), decrease the 'night' temperature
- - -
until appears.
TIMER MAN
) or ( ). Press (
L M
in display)
3TEMP
)
in display)
TEMP
)
et ). The timer allows you to
TEMP
3TEMP
- - -
is adjusted to , the motor will stay in
)
or ) by pressing briefly
TEMP
3TEMP
) and ( ) (minimum temperature : 40°F / 4°C).
L M
) and
L
)
L
) to
L
) or
M