General Section; Iimportant Safety Notice; Igeneral Fitting Information - Focus Drumfocus M-B-C User, Installation And Servicing Instructions

GENERAL SECTION

IMPORTANT SAFETY NOTICE
I
This appliance has a ceramic Fire-bed arrangement; this contains
Refractory Ceramic Fibres, which are man-made vitreous silicate fibres.
Excessive expo-sure to these materials can cause irritation to eyes, skin
and respiratory organs. Hence we recommend that when handling
these materials the release of dust should be kept to a minimum.
During installation and servicing we recommend that a HEPA filtered
vacuum be used to remove any dust and soot in and around the fire.
If any of the ceramic firme components need to be replaced we
recommend that the removed parts be sealed in a heavy-duty polythe-
ne bag, and be labelled as RCF waste. RCF is not "Hazardous waste"
and can be disposed of at a licensed tipping site for the disposal of
industrial waste.
The appliance incorporates an Oxygen Depletion Monitoring system.
(permanent pilot) This is located on the front of the burner, and must
not be adjusted by the installer. This system must not be put out of
operation, and if any parts require changing, only original manufactu-
rer parts shall be used.
This appliance is designed to be used either Natural or LPG gas howe-
ver, each individual appliance is only capable of running off the type
of gas spécifie at the time of purchase. It is important to note that
once a type of gas has been specified the stove cannot run off any
other type. The type of gas that your stove is capable of burning is sta-
ted on the data information panel.
This appliance has been designed, tested and approved to meet stan-
dards in place for product use, performance and safety. Installation of
your Stove must comply with current building regulations. It is there-
fore recommend that a CORGI engineer be employed for this task.
Taking particular notice of "thermal inversion" The engineer will pro-
vide you with information about the safety limits of the installation
and should fix a notice plate in a place where it can be readily seen.
This appliance is designed as an efficient heating device and conse-
quently all body parts become very hot in use. Except for the control
knob and control access door, which are designed to stay cool, all
other parts are working surfaces and should not be touched.
The glass and frame on this appliance acts as a fireguard conforming
to BS: 1945 – 1971 and satisfies the Heating Appliance (Fireguards)
régulations 1991. No part of the window or frame should be perma-
IT DOES NOT GIVE FULL PROTECTION FOR YOUNG
nently removed.
CHILDREN OR THE INFIRM
, extra protection should be considered for
these conditions conforming to BS 6539 or BS 6778.
Bearing in mind that the heat given off by this appliance may affect
articles placed close to it, curtains should not be placed within 30cm.
The appliance is not designed as a dryer. It is not therefore recommen-
ded that the appliance be used in such a manner. Do not place any
articles within 30cm of this appliance as this may result in damage to
the articles.
The installation must be carried out in accordance with the following
regulations:
The Building Regulations issued by the Department of the
Environment, the Building Standards (Scotland) (Consolidation)
Regulations issued by the Scottish Development Department.
BS 1251, BS 5440 part 1, BS 5871 part 2, BS 6461 part 1, BS 6891
and BS 8303
In the Republic of Ireland the installation must be also conform to the
relevant standards, particularly in regard to flue sizing and ventilation.
Refer to documents IS813, ICP3, IS327 and any other rules in force.
This appliance must be installed in accordance with the rules in force
and used only in a sufficiently ventilated space, and is intended for use
on a gas installation with a governed meter.
Before installation, check that this appliance is compatible with local
distribution conditions, nature of gas and pressure. The technical spe-
cification of this appliance is given on the rear page of this manual.
This appliance should not be used if the Glass is broken, and
should never be used with the Door open.
GENERAL FITTING INFORMATION
I
• Inlet pipe connection 8mm compression
• Chimney requirements Balanced Flue
• Flue monitor Permanent Pilot
• NO x level Class 1 (Nat. Gas), Class 5 (LPG)
User control: Variable rotary control inc. Integrated Piezo ignition,
Permanent pilot facility, Flame failure device and Oxygen Depletion
Cut-out.
Before installation of these appliances, the area into which the fire is
to be fitted must be cleared of all debris (including dust), in particular
combustible material.
• Battery type (Remote Versions only)
Receiver: 4x AA, R6 size.
Transmitter: PP3 (Alkaline only).
25