Performance Data Sheets - Culligan Aquasential Select Plus Series Owner's Manual

Performance Data Sheets

Culligan Aquasential Select Series 8" and 8" Outdoor Water Softener
Culligan knows the more informed you are about your water treatment systems, the more confident you will be about its performance� It's because
of this and more than seventy years of commitment to customer satisfaction that Culligan is providing this Performance Data Sheet to its customers�
NOTE!
Read this Performance Data Sheet and compare the capabilities of this unit with your actual water treatment needs.
It is recommended that before purchasing a water treatment unit, you have your water supply tested to determine
your actual water treatment needs.
Manufacturer: Culligan International Company
9399 W� Higgins Rd�, Suite 1100
Rosemont, IL 60018 USA
(847) 430-2800
www�culligan�com
Product: Culligan Aquasential Select Series 8" and 8" Outdoor Water Softener
Testing Conditions & Results:
Flow Rate:
Pressure:
Acidity:
Temperature:
Efficiency Rated dosage**:
Softener Specifications:
Service Flow Rate:
Operating Temp. Range:
Working Press� Range:
Substance Reduction
While testing was performed under standard laboratory conditions, actual performance may vary�
Name of Substance
Barium
Radium 226/228
This system is certified for barium and radium 226/228 reduction based on hardness reduction� It is recommended you
test your water every 6 months to ensure the system is performing properly and that hardness, and therefore barium
and radium 226/228, are being reduced�
The Culligan Aquasential Select Series 8" and 8" Outdoor Water Softeners have been tested and certified by
WQA against NSF/ANSI 372, CSA B483�1, and NSF/ANSI Standard 44 for the effective reduction of hardness
(calcium and magnesium), barium, and radium 226/228, as verified and substantiated by test data� To maintain
product certification and ensure uniform performance, the product is retested on a consistent basis�
This softener is efficiency rated, it has a Demand Initiated Regeneration (D�I�R) feature which complies with specific
performance specifications intended to minimize the amount of regenerant brine and water used in their operation� The
softener has a rated salt efficiency of not less than 3350 grains of total hardness exchange per pound of salt used (based
on NaCl equivalency), and shall not deliver more salt than its listed rating� The efficiency is measured by a laboratory test
described in NSF/ANSI Standard 44� This test represents the maximum possible efficiency that the system can achieve�
Operational efficiency is the actual efficiency achieved after the system has been installed� Operational efficiency is
typically less than the efficiency due to individual application factors including water hardness, water usage, and other
contaminants that reduce the softener's capacity� This model is efficiency rated�
Refer to the Specifications, Familiarization and Warranty section of this Owner's Guide (P/N 01040692) for more
specific product information� To avoid contamination from improper handling and installation, your system should
only be installed and serviced by your Culligan dealer� Performance will vary based on local water conditions� The
substances reduced by this system are not necessarily in your water�
Culligan water softeners are designed to work with any salt of good quality, although it is recommended that you ask your
local Culligan dealer for his suggestion on the best type and grade of salt to use in this softener�
NOTE!
This softener is not intended to be used for treating water that is microbiologically
unsafe or of unknown quality without adequate disinfection before or after the system.
** The efficiency rated dosage is only valid at the 3�0 lb salt dosage�
19
01040692 B 04/21
5�9 gpm @ 12 psi
30 - 40 psi
Non-Corrosive
68˚ (20˚C)
4,501 gr�/lb
5�9 gpm (22�3 Lpm)
33 - 120˚F (1 - 50˚C)
20 - 125 psi (140 - 860 kPa)
USEPA Max. Contaminant Level
2�0 mg/L
5 pCi/L
Capacity: 13,503 grains @ 3�0 lb salt
22,469 grains @ 9�0 lb salt
24,770 grains @ 12�0 lb salt
pH: 7.6
Pressure Drop at Max� Flow Rate: 12 psi (83 kPa)
Max. Drain Flow Rate:
Oper� Press� Range (Canada):
pH Flow Rate
7�5 ± 0�5 5�9 gpm
7�5 ± 0�5 5�9 gpm
1.05 gpm (4.0 Lpm)
20 - 90 psi (140 - 620 kPa)
Pressure
12 (psig)
12 (psig)