Advertisement
Table of Contents
- 1 Table of Contents
- 2 Important Safeguards
- 3 Grounding Instructions
- 4 Technical Specifications
- 5 Product Diagram
- 6 Installation
- 7 Preparing the Dispenser for Bottled Water
- 8 Initial Setup for a Bottled Water System
- 9 Adjusting the Siphon Tube for Smaller Bottles
- 10 Preparing the Water Dispenser for Use as a Bottle-Less System
- 11 Adding Filtration
- 12 Initial Set-Up for a Bottle-Less System
- 13 Operation
- 14 Cleaning and Maintenance
- 15 Clearing the In-Line Strainer
- 16 Troubleshooting
- Download this manual
Advertisement
Table of Contents
Related Manuals for Culligan BAEMUV1SHSK SSA
Summary of Contents for Culligan BAEMUV1SHSK SSA
- Page 1 User Guide Please read this instruction manual before using your water dispenser. BOTTOM LOAD/TRI-TEMP DIRECT CONNECT CONVERTIBLE WATER COOLER BAEMUV1SHSK SSA PBBLPOU...
-
Page 2: Table Of Contents
TABLE OF CONTENTS IMPORTANT SAFEGUARDS pg 3 GROUNDING INSTRUCTIONS pg 3 TECHNICAL SPECIFICATIONS pg 4 PRODUCT DIAGRAM pg 4 INSTALLATION Pg 5 PREPARING THE DISPENSER FOR BOTTLED WATER pg 5 INITIAL SETUP FOR A BOTTLED WATER SYSTEM pg 5 ADJUSTING THE SIPHON TUBE FOR SMALLER BOTTLES pg 6 PREPARING THE WATER DISPENSER FOR USE AS A BOTTLE-LESS SYSTEM pg 6... -
Page 3: Important Safeguards
• Do not use an extension cord as it may overheat, increasing the risk of fire. • If the supply cord is damaged, contact Culligan or a qualified electrician to replace it before plugging it in. • Never turn the dispenser upside down. If the dispenser has been resting on its side for a long period of time, place the it in the upright position for approximately 12 hours before using. -
Page 4: Technical Specifications
TECHNICAL SPECIFICATIONS RATED VOLTAGE 115V - 60Hz HOT WATER/HR 0.9 GAL (3.5 L) HEATING POWER 450W COLD WATER/HR 0.7 GAL (2.5 L) COOLING POWER/CURRENT 90W/1.5A HOT WATER TEMP. RANGE 165°F - 185°F (73.9°C - 85°C) COOLANT R134a 36g PRODUCT DIAGRAM FRONT BACK NIGHT LIGHT... -
Page 5: Installation
INSTALLATION 1. After unpacking, wipe dispenser with soft cloth. 2. Place the dispenser on a hard, flat surface, making certain it is level. The dispenser should not be placed near direct sunlight or any other source of heat. 3. It is best to place the dispenser in an area with good air circulation. Make sure there is at least 6 in (15cm) of clearance in back and on both sides of the dispenser for proper ventilation. -
Page 6: Adjusting The Siphon Tube For Smaller Bottles
ADJUSTING THE SIPHON TUBE FOR SMALLER BOTTLES Your new water dispenser features a water bottle cap with siphon tube that can accommodate various size bottles up to 5 gallons (19 liters) water bottle. The water bottle cap and siphon tube assembly is shipped in it’s default configuration for use with a standard 5 gallon (19 liter) bottle. -
Page 7: Adding Filtration
If inlet water pressure is greater than 100 psi, a pressure regulator must be installed prior to the water dispenser connection (not provided). Culligan offers options for filtration to be added to your cooler. Contact Culligan for details. Large, higher capacity filters will have to be mounted to the outside of the cooler. - Page 8 If inlet water pressure is greater than 100 psi, a pressure regulator must be installed prior to the water dispenser connection (not provided). Culligan offers options for filtration to be added to your cooler. Contact Culligan for details. Smaller filters can will have to be mounted inside the cooler.
-
Page 9: Initial Set-Up For A Bottle-Less System
INITIAL SET-UP FOR A BOTTLE-LESS SYSTEM IMPORTANT! Make sure both cooling system and hot water switches are off. 1. Locate the water supply switch on the back of the unit near the top. Switch the unit to POU. 2. Turn on the water supply to the unit. WATER SUPPLY SWITCH Plug the dispenser into a grounded GFCI power outlet. -
Page 10: Cleaning And Maintenance
CLEANING AND MAINTENANCE For maximum efficiency and performance, your water dispenser requires cleaning on a regular basis (ie. every 6 months). Regular cleaning will prevent potential growth of bacteria and will maintain a hygienic environment. Never use harsh chemicals or abrasive cleaners. Cleaning the Outside of the Water Dispenser The outside of the dispenser may be wiped clean with a cleaning solution product or a mild soap and water mixture and a soft cloth. -
Page 11: Clearing The In-Line Strainer
CLEANING AND MAINTENANCE Draining the Reservoirs IMPORTANT: UNPLUG THE DISPENSER BEFORE PERFORMING THIS PROCEDURE. 1. Dispense hot water from the water dispense point until the temperature drops to a safe level to avoid the risk of scalding. 2. Remove the water bottle or turn off the water supply. 3. -
Page 12: Troubleshooting
Move dispenser away from other objects. The buttons are stuck down. Check for foreign objects in the button area. Water leaks from the The water dispense point Contact Culligan Customer Service. water dispense point. has been damaged. 844-787-3148 Tighten the drain cap. - Page 13 Move dispenser away from other objects. The buttons are stuck down. Check for foreign objects in the button area. Water leaks from the The water dispense point Contact Culligan Customer Service. water dispense point. has been damaged. 844-787-3148 Tighten the drain cap.
- Page 14 BOTTOM LOAD/TRI-TEMP DIRECT CONNECT CONVERTIBLE WATER COOLER CULLIGAN INTERNATIONAL COMPANY 9399 West Higgins Rd | Rosemont, Illinois 60018 U.S.A. 844-787-3148 | www.culligan.com 041099-001 01037831 Rev A...