emaux EL-NP300 Series User Manual

Control

1 When the light is connected to the transformer directly, )
the on/off switch controls the colour changes
(Associating a light with a transformer and an on/off
switch is recommended; If you want all the lights to
change colour at the same time, install a master switch,
Figure 1).
2 If applicable, when the light is connected to the )
transformer and the transformer to the optional control
box, the control panel on the control box and its remote
control controls the colour changes (See the Control Box
Manual for details).

Maintenance of the Lights

• Do not leave the lights "on" above water for longer than 1 minute.
• Do not leave the lights directly under sunlight. Fill the pool with fresh water as soon as possible after the lights
are installed.
• Before switching on the lights, check whether the lights are fully submerged underwater and the circuit
boxes are running properly.
• This unit does not need any kind of maintenance. If it is not working properly, please contact EMAUX
authorized dealer where you purchase the unit from.
• Warranty will be voided if the Emaux Underwater Light was dismantled by unauthorized personnel.

REPLACEMENT PARTS

Item No. Part No. Description English
1 03011326 M6*80 Screws
03017075 Stainless Steel Lid ( EMAUX)
2
Plastic Lid (EMAUX)
01050008
3 03011327 M6*55 Hexagon Head Screws
4 01100011 Face Ring
04011153 Ultra-Thin 252 LED panel 20W,Warm white
04011151 Ultra-Thin 252 LED panel 20W,Cool white
04011152 Ultra-Thin 252 LED panel 20W,RGB
04011150 Ultra-Thin 252 LED panel 20W,Single Blue
04011107 Ultra-Thin 441 LED panel 35W,Warm white
04011105 Ultra-Thin 441 LED panel 35W,Cool white
5
04011106 Ultra-Thin 441 LED panel 35W,RGB
04011104 Ultra-Thin 441 LED panel 35W,Single Blue
04011181 Ultra-Thin 531 LED panel 50W,Warm white
04011179 Ultra-Thin 531 LED panel 50W,Cool white
04011180 Ultra-Thin 531 LED panel 50W,RGB
04011178 Ultra-Thin 531 LED panel 50W,Single Blue
6 03011360 M3*5 round head screw
7 02021085 Silica gel ring
8 01050105 Bottom cover
9 03011361 M4*10 round head self-tapping screw
2
10 04013004 2* 1. 5mm * 2.5m( D8) Cable
11 02010285 NBR ring
12 03012125 M4*10 flat head self-tapping screw
13 01051253 fixed position plate
14 01230003 Waterproof Cover
15 89041602 Nut Fitting
16 89041603 Fastening Dog
17 89041604 Water Joint Fittings for Cable
18 89041608 Vinyl pool fitting for NP300
19 01050010 NP300 Lights Niche
20 89041605 Plug with O- Ring
Joint for wire & pipe
21 01171106
Master Switch
ON/OFF Switch ON/OFF Switch ON/OFF Switch
Light Light Light
Figure 9
Qty
2
1
1
6
1
1
10
11
12
2
1
1
5
1
2
2
21
6
1
6
2
1
1
1
1
1
4-4
EL-NP300 Series Underwater Light
User Manual

SAFETY WARNINGS

• Only qualified electrician is allowed to carry out the installation of this product.
• Avoid direct contact with electrical power.
• Respect all regulations in effect for preventing accidents.
• All units are required to be disconnected from the main electricity before any operation of maintenance.
• Never handle with wet hands and feet.
• This unit is design for use only when fully submerged in fresh water, connecting with a safety transformer
• Never operate this Underwater Light for more than 1 minute unless it is totally submerged in water.
• Be sure power is off before installing or removing LED plate. Allow LED plate to cool before replacing.
• This product should be installed according to your local electrical installation ordinances and regulations
• Maximum Depth for Light installation at 1 meter.
• Maximum Water Temperature Range for light operation 0 - 30 C.
- for type Z attachments
The external flexible cable or cord of this luminaire cannot be replaced;if the cord is damaged,the
luminaire shall be destroyed.

SPECIFICATION

A) Electrical Specification : 1) Voltage : AC12V
B) Colour change options(For RGB version only) :
1
White
1
2 3 Blue
3 5 Red+Green
4
Mode A: Blue+ Gradual Red
7
5
9 Mode C: Blue+Gradual Green
6
Mode E: RGB Colour Sequence: Red>Green>Blue
11
7
8
Mode F: Four Colour Sequence: Red>Green>Blue
13
9
>Purple
13
14

General Information

15
Never install in vertical position with the lamp facing upwards / downwards, Intended for fresh & salt water
16
swimming pool
17
A) Ensure that the electrical system of your pool conforms to the following requirements of all local codes
and ordinances. A licensed or certified electrician must install the electrical system to meet or exceed
18
those requirements before the niche (fixture-housing) is installed.
B) Installation Guideline:
19 1) The top of the light lens be at least 18 inches (457mm) below the water level. Some installers position the
niche 24 inches (610mm) below anticipated water level to avoid any inspection authority issues with this
requirement.
2) The lighting circuit must have a Ground Fault Circuit
20 Interrupter (GFCI), and an appropriately rated circuit
breaker.
3) The junction box or the low voltage transformer is located
at least 8 inches (203mm) above water level and at least 48
inches (1912mm) from the edge of the pool
o
2) Frequency : 50/60Hz 3) Power : 20W / 35W / 50W.
Green
2
4 Green+Blue
6 Red+Blue
8 Mode B: Green+Gradual Red
10 Mode D: Blue+Gradual Red
12 Auto Colour Change
Rapid Auto Colour Change
14
Figure 1
1 -4
EMLI16082530