emaux E-Lumen Compact Operating Manual

www.emauxgroup.com
SAFETY WARNINGS
• Only qualified electrician is allowed to carry out the installation of this product.
• Avoid direct contact with electrical power.
• Understand all regulations in effect for preventing accidents.
• Switch off power to transformer before repairing or replacing the light.
• Never handle with wet hands and feet.
• This unit is design for use only when fully submerged in water, please use
with suitable transformer.
• Never operate this Underwater Light for more than 1 minute unless it is totally
submerged in water.
• This product should be installed according to your local electrical installation
ordinances and regulations.
• Maximum Depth for Light installation at 1 meter.
• Maximum Water Temperature Range for light operation 0 - 30 C.
SPECIFICATION
A. Electrical Specification : 1) Voltage : AC12V
3) Power : 10W.
B. Colour change options(For RGB version only)
4. For training or competition pools, the lights must be installed on the sides in
order to prevent swimmers from seeing any glare.
5. Nothing should be placed on the poolside directly above the lights for ease of
future maintenance.
6. Please ensure all wires and connections are sealed and waterproofed to
avoid any damage.
7. The cables connecting the lights and the transformers must be at least 6mm
and the distance between them must not exceed 30m (Figure 2); otherwise
the lights will not function properly.
Transformer
INSATALLATION OF THE UNDERWATER LIGHT
A. Preparing to Install
1. Before installation, a circuit system diagram must be designed by a certified
engineer.
2. The circuit system must comply with local laws and regulations and must be
carried out by qualified electricians.
3. Make sure the voltage is 12V and the terminal box is at least 120cm from the
poolside (Figure 3).
4. Upon installation, top of the light must be at least 45cm from water surface
(Figure 3).
Junction box
120cm min.
Rigid conduit
E-Lumen Compact
UNDERWATER LIGHT OPERATING MANUAL
Model：ELCOMP-N ELCOMP
Keep this manual for future reference
o
2) Frequency : 50/60Hz
EMLI14060701
8-1
Light
30m
Figure 2
Water level
45cm min. from water line to top of lens
Concrete must be cut background
niche to allow for a compact plaster
seal
Figure 3
8-3
White
1
Green
2
Blue
3
Green+Blue
4
Red+Green
5
6 Red+Blue
Mode A: Blue+ Gradual Red
7
Mode B: Green+Gradual Red
8
Mode C: Blue+Gradual Green
9
Mode D: Blue+Gradual Red
10
Mode E: RGB Colour Sequence: Red>Green>Blue
11
Auto Colour Change
12
Mode F: Four Colour Sequence: Red>Green>Blue>Purple
13
Rapid Auto Colour Change
14
CONTROL
1. When the light is connected to the
transformer directly, the on/off switch
controls the colour changes (a light with a
transformer with an on/off switch is
recommended; If you want all the lights to
change colour at the same time, please
install a master switch, Figure 1).
2. If applicable, when the light is connected
to the transformer and the transformer to
the optional control box, the control panel
on the control box and its remote control
controls the colour changes (See the
Control Box Manual for details).
INSTALLATION NOTES
1. Each cable have 2.5m long. Please follow the procedures when installing the
light.
2. It is recommended to install a light in every 4m , the approximate exposure
area of each unit.
3. The lights should be installed in the direction that they will not shine directly
into the house.
B. Pool Installation
1. Embed the Shell into the concrete wall, making sure that it is parallel to the
side of the pool (Figure 4).
2. Place the Mounting Plate on the concrete wall and tighten it with 6 screws.
(Figure 5).
3. Note that the light must only be installed on a flat or concave surface.
2 4. Wrap extra cables behind the light to make sure it could be taken to the pool
surface for future maintenance .Then tighten the nut or line pipe joint
(Figure 6).
5. Hang the light onto the Mounting ring and tighten the screws (Figure 7).
6. The wire connections inside the terminal box must be sealed by leak-proof
tapes to prevent water from leaking into the terminal box through the cables.
Figure 4
Figure 6
Master Switch
ON/OFF Switch
Light
Figure 1
2
8-2
Figure 5
or
Figure 7
8-4
ON/OFF Switch ON/OFF Switch
Light Light