emaux UL-P300 Series User Manual

One remote control can be max control 12pieces
Side control button
N = On
F = Off
Control Distance
Underwater 250mm, Max control distance 20m
Underwater 500mm, Max control distance 8m
Working in air, Max control distance 50m
Control Angle
Control Angle < 60°
In swimming pool
A position control A lamp
B position control B lamp
Authorized use in all EU countries, no restriction. Conform to the directive R&TTE 1999/5/CE
REPLACEMENT PARTS
Key
Part No.
No.
1 03011323
1 03011325
2 01051066
2 01051067
3 02021011
4 04011004
4 04011043
4 04011044
4 04011045
4 04011056
4 04011047
4 04011048
4 04011049
5 02021001
6 01271001
7 89040301
8 89040312
9 03014002
10 89040304
11 01171107
12 01171106
13 04013072
Figure 5.
Description
M5X40 Screw for Face Plate for Vinyl Pool
M5X25 Screw for Face Plate for Concrete Pool
Face Plate (Blank)
Face Plate (Emaux)
Gasket for Bulb
PAR56 Light Bulb (Yellow Light) (Standard Bulb)
Par56 252 LED Bulbs (White-Colour)
Par56 252 LED Bulbs (Blue Colour)
Par56 252 LED Bulb (With Remote Control)
Par56 (252 LED Bulbs)12V/16W (Automatic Colour
Change)
Par56 144 LED Bulbs (White Colour)
Par56 144 LED Bulbs (Blue Colour)
Par56 144 LED Bulbs (Automatic Colour Change)
Waterproof O-Ring for bulb
Waterproof Cover
Waterproof O-Ring with Tooth Head for Cable
Water Joint Fittings for Cable
Spring
P300 Lights Vinyl pool fitting
P300 Lights Niche
Joint for Wire & Pipe
Cable 2.5M
4-4
UL-P300 / LED-P300 Series Underwater Light
User Manual
KEEP THIS USER MANUAL SAVE FOR FUTURE REFERENCE
RISK OF ELECTRICAL SHOCK OR ELECTROCUTION
Qty
This underwater light fixture must be installed by a licensed or certified electrician or a qualified serviceman
in accordance to the requirements of your government standard or local authorities. Improper installation
1
will create electric hazards which could result in serious injury, death as well as damage to the property.
1
Before servicing the light, disconnect the power supply from the circuit breaker. Failure to do so could result
1
in serious injury, death and or damage to the property.
1
1
1
A) Preparatory steps which must be completed by the electrician before light is installed, see Figure 1.
1
1) Ensure that the electrical system and its wiring for the
pool conform to the requirements of your govenment or
1
your local authorities. The installation of the Underwater
1
Light should only be performed by a licensed
electrician.
1
a) The junction box, or the low voltage transformer for 12
volt Underwater Light model is to be located at least
1
120CM from the edge of the pool, see Figure 1.
1
b) The junction boxes shall not be installed in zones 0
2,where permitted for SELV circuits.
1
c) Terminal blocks must meet the IEC60988-2-1 standard
1
having the rated connecting capacity of 4,0mm2 use
1
of screw-type terminal at least 25A rated current
,mounted on junction boxes inside. See Figure 0
1
1
1
1
1
d) The light fixture and all metal parts that are within 240CM
1
of the pool must be properly protected with non-ductile
materials and that the connections must be waterproof.
1
PLEASE READ THE FOLLOWING CAREFULLY AND
DANGER !

INSTALLATION

1 and
,
To power source;
feed paraffin
Rigid conduit
Concrete must be cut back
around niche to allow for
a compact plaster seal
Figure 0.
1 -4
120cm Min.
Water level
45cm Min. from water
line to top of lens
25CM
6.6CM
Figure 1.
EMLI16022770