Download Print this page
emaux UL-P100 Series Operating Procedures
Hide thumbs Also See for UL-P100 Series:

Advertisement

Quick Links

WARNING
Never operate this pool lamp for more than 10 seconds unless it is totally submerged in water. Without total
submersion, the lamp assembly will get extremely hot, which may result in serious injury to pool users, installers,
or bystanders, or in damage to property.
Be sure power is off before installing or removing lamp. Allow lamp to cool before relamping. This light fixture
uses a Halogen Quartz lamp. Do Not touch lamp with bare hand, this may severely reduce its life. Use the
plastic furnished with the replacement lamp to eliminate finger prints pin from the bulb.
lFor use only when immersed in water, IP68
lFor operation only with approved safety isolating transformer: Input:230V Output: 12V~ 75VA
lThe safety isolating transformer must meet the EN61558-2-6 standard lSELV, the safety source shall be installed
outside of Zone 0, 1 and 2. If you want to replacement the lamp, loosen the screw of back cover, open the
back cover and replace the lamp, and carefully fixed gasket seal, re-tightening the screw. The replacement
takes place from the side of the luminaires in contact with the water but after the water of the pool has been
partially or completely drained.
CAUTION: Never try to repair or replace the lamp by yourself. If this underwater light fixture is out of working, it
shall be repaired or replaced by the manufacturer or his service agent or similarly qualified persons in order to
avoid a hazard.
CAUTION: The transparent plastic Protective Shield can not be replaced, if the Protective Shield is cracked,
this underwater light fixture shall be scrapped.
REPLACEMENT PARTS
Key
Part No.
Description
No.
1*
01221002
Colour lens (Red+Green+Blue) for P100
2
03011321
M5*20 Screw (316#)
3
01051059
Face Ring
4
01041021
P100 Lights Lens
5
03021018
M6 Brass Nut
6
01051058
P100 Lights Face plate
7
02021004
O-ring
8
04011002
Halogen light bulb (Yellow Light)
9
89040201
P100 Lights Body set
10
03011320
M6*20 Screw (316#)
11
04013004
2.5M Cable
12
89040203
Concrete Pool Fittingfor P100
13
89044501
Vinyl Pool Fitting for P100
Notes:1* 01221001 is UL-P100 Light Colour Lens 1 set with (Red+Green+Blue)
Qty
1
1
1
1
8
1
1
1
1
8
1
1
1
4-4
UL-P100 Series Underwater Light
Operating Procedures
Please read the following carefully and
keep this user manual save for future reference
DANGER !
RISK OF ELECTRICAL SHOCK OR ELECTROCUTION
This underwater light fixture must be installed by a licensed or certified electrician or a
qualified serviceman in accordance to the requirements of your government standard or
local authorities. Improper installation will create electric hazards which could result in
serious injury, death as well as damage to the property. Before servicing the light,
disconnect the power supply from the circuit breaker. Failure to do so could result in serious
injury, death and or damage to the property.
1-4
EMLI16022765

Advertisement

loading
Need help?

Need help?

Do you have a question about the UL-P100 Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for emaux UL-P100 Series

  • Page 1 Zone 0, 1 and 2. If you want to replacement the lamp, loosen the screw of back cover, open the UL-P100 Series Underwater Light back cover and replace the lamp, and carefully fixed gasket seal, re-tightening the screw. The replacement takes place from the side of the luminaires in contact with the water but after the water of the pool has been partially or completely drained.
  • Page 2 INSTALLATION B) Perform the following steps after the electrical system requirements are met. A) Preparatory steps which must be completed by the electrician before light 1 Locate position on a vertical wall where light is to be installed. The top of the light lens must be 45cm below normal water level, and maximum depth for luminaire is 2.5m, see Figure 1.