Edge-Core AS7712-32X Safety And Regulatory Information Manual

Safe t y & Regulator y I nfo rmation
32-Port 100G Fiber Ethernet Switch
AS7712-32X | AS7716-32X
FCC Class A
This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
You are cautioned that changes or modifications not expressly approved
by the party responsible for compliance could void your authority to
operate the equipment.
You may use unshielded twisted-pair (UTP) for RJ-45 connections -
Category 3 or better for 10 Mbps connections, Category 5 or better for
100 Mbps connections, Category 5, 5e, or 6 for 1000 Mbps connections.
For fiber optic connections, you may use 50/125 or 62.5/125 micron
multimode fiber or 9/125 micron single-mode fiber.
CE Mark
CE Mark Declaration of Conformance for EMI and Safety (EEC)
This information technology equipment complies with the requirements
of the Council Directive 2004/108/EC on the Approximation of the laws
of the Member States relating to Electromagnetic Compatibility and
2006/95/EC for electrical equipment used within certain voltage limits
and the Amendment Directive 93/68/EEC. For the evaluation of the
compliance with these Directives, the following standards were applied:
RFI Emission:
◆
Limit according to EN 55032:2012+AC:2013, Class A
◆
Limit for harmonic current emission according to EN 61000-3-
2:2014, Class A
◆
Limitation of voltage fluctuation and flicker in low-voltage supply
system according to EN 61000-3-3:2013
Immunity:
◆
Product family standard according to EN 55024:2010
◆
Electrostatic Discharge according to IEC 61000-4-2:2008
◆
Radio-frequency electromagnetic field according to IEC 61000-4-
3:2010
◆
Electrical fast transient/burst according to IEC 61000-4-4:2012
◆
Surge immunity test according to IEC 61000-4-5:2014
◆
Immunity to conducted disturbances, Induced by radio-frequency
fields: IEC 61000-4-6:2013
◆
Power frequency magnetic field immunity test according to IEC
61000-4-8:2009
◆
Voltage dips, short interruptions and voltage variations immunity
test according to IEC 61000-4-11:2004
LVD:
◆
EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013
www.edge-core.com
The Declaration of Conformity (DoC) can be obtained from www.edge-
core.com -> support -> download.
Japan - VCCI Class A
Laser Safety
Warning: Fiber Optic Port Safety:
When using a fiber optic port, never look at the
CLASS 1
transmit laser while it is powered on. Also, never look
LASER PRODUCT
directly at the fiber TX port and fiber cable ends when
they are powered on.
Avertissment: Ports pour fibres optiques - sécurité sur le plan optique
Ne regardez jamais le laser tant qu'il est sous tension.
PRODUIT LASER
Ne regardez jamais directement le port TX
DE CLASSE 1
(Transmission) à fibres optiques et les embouts de
câbles à fibres optiques tant qu'ils sont sous tension.
Warnhinweis: Faseroptikanschlüsse - Optische Sicherheit:
Niemals ein Übertragungslaser betrachten, während
LASERPRODUKT
dieses eingeschaltet ist. Niemals direkt auf den Faser-
DER KLASSE 1
TX-Anschluß und auf die Faserkabelenden schauen,
während diese eingeschaltet sind.
警告：光纤端口安全 :
使用光纤端口时，切勿在其电源处于开启状态时注
视发射激光器。此外，切勿在光纤 TX 端口和光纤
端头的电源处于开启状态时直接注视它们。
PSE Alarm
本製品に同梱いたしております電源コードセットは、本製品専用です。本
電源コードセットは、本製品以外の製品並びに他の用途でご使用いただく
ことは出来ません。製品本体に同梱された電源コードセットを利用し、他
製品の電源コードセットを使用しないで下さい。
Power Cord Safety
Please read the following safety information carefully before installing
the switch:
Warning: Installation and removal of the unit must be carried out by
qualified personnel only.
◆
The unit must be connected to an earthed (grounded) outlet to
comply with international safety standards.
◆
Do not connect the unit to an A.C. outlet (power supply) without an
earth (ground) connection.
◆
The appliance coupler (the connector to the unit and not the wall
plug) must have a configuration for mating with an EN 60320/IEC
320 appliance inlet.
– 1 –
:
150200001280A
E082018-AP-R04