1. Manuals
  2. Brands
  3. Siemens Manuals
  4. Network Router
  5. SIMOTICS CONNECT 400
  6. Manual

Siemens SIMOTICS CONNECT 400 Manual

Router kit
Hide thumbs Also See for SIMOTICS CONNECT 400:
Table of Contents

Advertisement

Quick Links

Application example
SIMOTICS CONNECT 400 –
Router Kit
05/2020
_________________
Documentation guide
__
_________________
Safety information
__
_________________
Use cases
__
___________
Installing Router Kit
components in the
installation enclosure
_________________
Commissioning the Router
Kit WLAN / LTE
__
_________________
Commissioning the Router
Kit WLAN / LAN
__
Commissioning the Router
Kit LAN / LTE
1
2
3
4
5
6
7

Advertisement

Table of Contents
loading

Related Manuals for Siemens SIMOTICS CONNECT 400

Summary of Contents for Siemens SIMOTICS CONNECT 400

  • Page 1 Documentation guide _________________ Safety information _________________ Use cases Application example ___________ Installing Router Kit components in the SIMOTICS CONNECT 400 – installation enclosure Router Kit _________________ Commissioning the Router Kit WLAN / LTE _________________ Commissioning the Router Kit WLAN / LAN...
  • Page 2 Please note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If third-party products and components are deployed, then they must be recommended or approved by Siemens. These products can only function correctly and safely if they are transported, stored, set up, mounted, installed, commissioned, operated and maintained correctly.

  • Page 3: Table Of Contents

    Commissioning the Router Kit LAN / LTE ....................86 Preparing the hardware ......................86 Setting up interfaces ....................... 86 Configuring SCALANCE M876-4 .................... 89 7.3.1 Logging in to the Web-based Management Tool ..............89 Application example for SIMOTICS CONNECT 400 - Router Kit...
  • Page 4 Making settings in the wizard ....................93 7.3.4 Configuring a firewall ......................98 7.3.5 Updating the DHCP server ....................98 Appendix ..............................100 Service and support ......................100 Industry Mall ......................... 101 Change documentation ......................101 Application example for SIMOTICS CONNECT 400 - Router Kit...

  • Page 5: Documentation Guide

    1 Documentation guide With the Router Kit, you can provide an Internet connection via WLAN e. g. for SIMOTICS CONNECT 400. All settings for the Router Kit made in the document ensure that SIMOTICS CONNECT 400 is visible in WLAN.

  • Page 6: Safety Information

    WARNING Electrical machines have live parts Contact with live parts may cause death or severe personal injury. Install the fan module mechanically in the device before you make the electrical connection. Application example for SIMOTICS CONNECT 400 - Router Kit...
  • Page 7 • Always observe the "Five safety rules (page 6)" when working on the machine. • Only remove covers in line with these operating instructions. • Operate the machine properly. • Maintain the machine regularly and correctly. Application example for SIMOTICS CONNECT 400 - Router Kit...

  • Page 8: Use Cases

    ● You can provide an Internet connection, but not WLAN. ● Product recommendation: Router Kit WLAN / LAN: SCALANCE W774-1. Use case 3: ● You cannot provide an Internet connection ● Product recommendation: Router Kit LAN / LTE: SCALANCE M876-4 Application example for SIMOTICS CONNECT 400 - Router Kit...

  • Page 9: Installing Router Kit Components In The Installation Enclosure

    Installation wire/bl. Installation wire/gr. The following additional components are not included in the scope of delivery but are required: ● SIM card ● PC with Windows system ● LAN adapter Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 10 Figure 4-1 Structure of Router Kit WLAN / LTE Note: The parts list is designed for the European market. The MLFBs of the required components may differ in other countries. Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...

  • Page 11: Installing The Router Kit Wlan / Lte In The Installation Enclosure

    4.2 Installing the Router Kit WLAN / LTE in the installation enclosure Procedure 6. Drill two fastening holes in the installation enclosure. Figure 4-2 Drill hole on the left with DIN rail and components already installed Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 12 Both holes on rear of installation enclosure 7. Adjust the DIN rail to the installation enclosure and grind down any sharp edges. The fastening holes in the DIN rail are already there. Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 13 Figure 4-4 View of front, secured combi screw Figure 4-5 View of rear, secured combi screw with washer, spring washer and nut 9. Insert the SIM card into SCALANCE M876-4. Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 14 10. Attach the SITOP compact 24V/1.3A, SCALANCE M876-4 and SCALANCE W774-1 to the DIN rail. Figure 4-6 From left to right: Fuse, SITOP compact 24V/1.3A, SCALANCE W774-1 and SCALANCE M876-4 Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 15 4.2 Installing the Router Kit WLAN / LTE in the installation enclosure 11. Attach the protective conductor terminal block to the DIN rail. Figure 4-7 Yellow/green protective conductor terminal block Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 16 4.2 Installing the Router Kit WLAN / LTE in the installation enclosure 12. Attach the two universal terminals (gray) with intermediate plates (yellow) to the DIN rail. Figure 4-8 Gray universal terminals with yellow intermediate plates Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 17 – Mount the second end retainer to the left of the last gray universal terminal. ③ – Mount the third end retainer between SCALANCE M876-4 and the protective conductor terminal block. Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 18 14. Pull the cables through the pre-drilled holes at the bottom and secure the cable glands with the locknuts. Figure 4-9 Attached cable glands 15. Wire the elements as shown in the terminal connection diagram. Figure 4-10 Terminal connection diagram Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 19 Attachment of antenna cable between SCALANCE W774-1 (connection: R1 A1, R1 A2) and the two antennas ANT792-6MN • Attachment of antenna with antenna cable with SCALANCE M876-4 (connection: A1) Result Installation is complete. Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 20 4 Installing Router Kit components in the installation enclosure 4.2 Installing the Router Kit WLAN / LTE in the installation enclosure Figure 4-11 Setup after installation is complete Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...

  • Page 21: Parts List For The Router Kit Wlan / Lan

    Installation wire/bl. Installation wire/gr. The following additional components are not included in the scope of delivery but are required: ● SIM card ● PC with Windows system ● LAN adapter Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 22 Figure 4-12 Structure of Router Kit WLAN / LAN Note: The parts list is designed for the European market. The MLFBs of the required components may differ in other countries. Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...

  • Page 23: Installing The Router Kit Wlan / Lan In The Installation Enclosure

    4.4 Installing the Router Kit WLAN / LAN in the installation enclosure Procedure 16. Drill two fastening holes in the installation enclosure. Figure 4-13 Drill hole on the left with DIN rail and components already installed Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 24 Both holes on rear of installation enclosure 17. Adjust the DIN rail to the installation enclosure and grind down any sharp edges. The fastening holes in the DIN rail are already there. Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 25 Figure 4-15 View of front, secured combi screw Figure 4-16 View of rear, secured combi screw with washer, spring washer and nut Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 26 4.4 Installing the Router Kit WLAN / LAN in the installation enclosure 19. Attach the SITOP compact 24V/1.3A and the SCALANCE W774-1 to the DIN rail. Figure 4-17 Fuse, SITOP compact 24V/1.3A, SCALANCE W774-1 to the right Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 27 4.4 Installing the Router Kit WLAN / LAN in the installation enclosure 20. Attach the protective conductor terminal block to the DIN rail. Figure 4-18 Yellow/green protective conductor terminal block Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 28 4.4 Installing the Router Kit WLAN / LAN in the installation enclosure 21. Attach the two universal terminals (gray) with intermediate plates (yellow) to the DIN rail. Figure 4-19 Gray universal terminals with yellow intermediate plates Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 29 – Mount the second end retainer to the left of the last gray universal terminal. ③ – Mount the third end retainer between SCALANCE W774-1 and the protective conductor terminal block. Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 30 Wiring of SITOP compact 24V/1.3A with the three universal terminals Green frame Attachment of antenna cable between SCALANCE W774-1 (connection: R1 A1, R1 A2) and the two antennas ANT792-6MN Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 31 4 Installing Router Kit components in the installation enclosure 4.4 Installing the Router Kit WLAN / LAN in the installation enclosure Result Installation is complete. Figure 4-22 Setup after installation is complete Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...

  • Page 32: Parts List For The Router Kit Lan / Lte

    Installation wire/bl. Installation wire/gr. The following additional components are not included in the scope of delivery but are required: ● SIM card ● PC with Windows system ● LAN adapter Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 33 4.5 Parts list for the Router Kit LAN / LTE Figure 4-13 Structure of Router Kit LAN/LTE Note: The parts list is designed for the European market. The MLFBs of the required components may differ in other countries. Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...

  • Page 34: Installing The Router Kit Lan / Lte In The Installation Enclosure

    4.6 Installing the Router Kit LAN / LTE in the installation enclosure Procedure 25. Drill two fastening holes in the installation enclosure. Figure 4-23 Drill hole on the left with DIN rail and components already installed Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 35 Both holes on rear of installation enclosure 26. Adjust the DIN rail to the installation enclosure and grind down any sharp edges. The fastening holes in the DIN rail are already there. Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 36 Figure 4-25 View of front, secured combi screw Figure 4-26 View of rear, secured combi screw with washer, spring washer and nut Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 37 4.6 Installing the Router Kit LAN / LTE in the installation enclosure 28. Attach the SITOP compact 24V/1.3A and the SCALANCE M876-4 to the DIN rail. Figure 4-27 Fuse, SITOP compact 24V/1.3A, SCALANCE M876-4 to the right Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 38 4.6 Installing the Router Kit LAN / LTE in the installation enclosure 29. Attach the protective conductor terminal block to the DIN rail. Figure 4-28 Yellow/green protective conductor terminal block Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 39 4.6 Installing the Router Kit LAN / LTE in the installation enclosure 30. Attach the two universal terminals (gray) with intermediate plates (yellow) to the DIN rail. Figure 4-29 Gray universal terminals with yellow intermediate plates Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 40 – Mount the second end retainer to the left of the last gray universal terminal. ③ – Mount the third end retainer between SCALANCE W774-1 and the protective conductor terminal block. Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 41 32. Pull the cables through the pre-drilled holes at the bottom and secure the cable glands with the locknuts. Figure 4-30 Attached cable glands 33. Wire the elements as shown in the terminal connection diagram. Figure 4-31 Terminal connection diagram Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 42 Wiring of SITOP compact 24V/1.3A with the three universal terminals Green frame Attachment of antenna cable between SCALANCE M876-4 (connection: R1 A1) and the antenna ANT794-4MR Result Installation is complete. Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...

  • Page 43: Commissioning The Router Kit Wlan / Lte

    LTE module (default IP of the LTE module is 192.168.1.1). ● You require administrator rights to download the PST. ● You need a ready-for-use LAN adapter to set the IP address. Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 44 Opening the Network and Sharing Center 38. Select the "Change adapter settings" option. 39. Right-click the adapter used and select the "Properties" command from the shortcut menu. Figure 5-2 Selecting properties Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 45 5 Commissioning the Router Kit WLAN / LTE 5.2 Setting up interfaces 40. Select the "Internet Protocol Version 4 (TCP/IPv4)" entry and click the "Properties" button. Figure 5-3 Selecting the Internet protocol Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 46 – Set the check mark for "Use the following DNS server addresses". Preferred DNS server: 192.168.1.1 (In general: The IP address of the LTE module is entered as preferred DNS server) Figure 5-4 Entering Internet protocol properties Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...

  • Page 47: Setting The Ip Address Of The Scalance W774-1

    42. Open the PST. Figure 5-5 PST start page 43. Select the "Set PG/PC Interface" command in the menu bar under "Settings". Figure 5-6 Opening the "PG/PC Interface" settings Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 48 45. Click the " " button in the toolbar to search for a module. The modules are displayed. Figure 5-8 Listed modules 46. Open the lower-level menu by clicking the "+" symbol and select the menu entry "Ind. Ethernet interface". Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 49 – As IP address, enter the IP address of the LTE module (here: 192.168.1.1). Figure 5-9 Entering the Ind. Ethernet interface field 48. Click the "Load" button and confirm the subsequent dialog with "Yes". 49. Close the PST. Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...

  • Page 50: Configuring Scalance M876-4

    (192.168.1.1) in the browser. 52. Log in with the following entries: – Name: admin – Password: admin Figure 5-10 Password input You are prompted to change the default password. Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 51 5 Commissioning the Router Kit WLAN / LTE 5.4 Configuring SCALANCE M876-4 53. Change the password. Figure 5-11 Changing the password 54. Close the Web-based Management Tool. Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...

  • Page 52: Loading Firmware

    57. If the firmware does not have the most recent version, proceed as follows: 58. You will find the latest firmware on the Internet (https://support.industry.siemens.com/cs/ww/en/ps/6GK5876-4AA00-2BA2/dl). 59. Download the most recent firmware and extract the download. Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 53 5.4 Configuring SCALANCE M876-4 60. Select the "HTTP" tab under "System > Load&Save" and download the new firmware. Figure 5-13 Loading the firmware 61. Perform a restart after the loading process. Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...

  • Page 54: Making Settings In The Wizard

    64. In the "SIM" tab, enter the PIN of the SIM card, remove the check mark for "Enable Mobile Network Interface" and set the check mark for "Allow Data Roaming". Figure 5-15 Entering the PIN of the SIM card Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 55 65. In the "Operator" tab, select the network provider with a check mark in the "Enabled" column. If the desired network provider is not in the table, select the network provider via the "Country List" and "Provider List". Figure 5-16 Selecting the network provider Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 56 5.4 Configuring SCALANCE M876-4 66. In the "Time" tab, set the check mark for "NTP Client" and enter the address "de.pool.ntp.org" under "NTP Server Address". Figure 5-17 Time setting Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 57 5 Commissioning the Router Kit WLAN / LTE 5.4 Configuring SCALANCE M876-4 67. Check your settings in the "Summary" tab and click "Set Values". Figure 5-18 Wizard summary Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 58 68. The status "Registered to home network (network strength)" is displayed on the start page under "Connection Status". If this status is not displayed, check the connection of the antenna cable and click "Refresh". Figure 5-19 SCALANCE M876-4 start page Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...

  • Page 59: Configuring A Firewall

    69. Select the "IP Rules" tab under "Security > Firewall". 70. Make the following settings in the table: – Action: Accept – From: vlan1 (INT) – To: usb0 Figure 5-20 Correct setting of the firewall Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...

  • Page 60: Updating The Dhcp Server

    "Changes will be saved automatically in 60 seconds. Press "Write Startup Config" to save immediately" and then on "Write Startup Config". 5.4.5 Updating the DHCP server Procedure 73. Switch to the menu "System > DHCP". Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 61 Lower and Upper Address. Make sure to stay in the same subnet (192.168.1.x). Figure 5-21 Setting the DHCP server 75. In the "DHCP Options" tab, make the settings as shown in the figure. Figure 5-22 Setting the DHCP options Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...

  • Page 62: Commissioning The Router Kit Wlan / Lan

    (192.168.1.20) in the browser. 78. Log in with the following entries: – Name: admin – Password: admin Figure 6-1 Password input You are prompted to change the default password. Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...

  • Page 63: Loading Firmware

    82. Check the version of the firmware under "Information > Versions". 83. You will find the latest firmware on the Internet (https://support.industry.siemens.com/cs/ww/en/ps/6GK5774-1FX00-0AA0). 84. Download the most recent firmware and extract the download. Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 64 6.1 Configuring the SCALANCE W774-1 85. Select the "HTTP" tab under "System > Load&Save" and download the new firmware. Figure 6-3 Loading the firmware update 86. Perform a restart after the loading process. Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...

  • Page 65: Making Settings In The Wizard

    87. Run through the wizard. – Select the user country in the "Country" tab under "Country Code". The selected user country determines the availability of channels. Figure 6-4 Selecting the user country Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 66 192.168.1.1. Figure 6-5 Checking IP addresses 89. In the "Management Interfaces" tab, set the check mark for "SSH Server" and disable the "Telnet Server". Figure 6-6 Selecting the server Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 67 91. To enable the WLAN, set the check mark for "Enabled" in the "Radio" tab. Adapt the send power to the provisions applicable in your country. "Allowed" must appear under "Tx Power Check". Figure 6-8 Enabling the WLAN Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 68 CONNECT 400 will not be available in the WLAN. Figure 6-9 Selecting the channel 93. In the "AP" tab, enter the desired WLAN name next to the port setting under "SSID". Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 69 94. In the "Security" tab, select the "Authentication Type" "WPA2-PSK". Assign a password under "WPA(2) Pass Phrase" and repeat the entry under "WPA(2) Pass Phrase Confirmation". The password is the network key for WLAN access. Figure 6-10 Password/network key assignment Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...

  • Page 70: Preparing The Hardware

    97. Attach the LAN cable between the WLAN module (SCALANCE W774-1) and a PC with adapter. 98. Supply the Router Kit with a voltage of 230 V AC (SITOP PSU100C). Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...

  • Page 71: Setting Up Interfaces

    99. To open the "Network and Sharing Center", right-click on the WLAN symbol in the taskbar and select the command "Open Network and Sharing Center". Figure 6-12 Opening the Network and Sharing Center 100. Select the "Change adapter settings" option. Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 72 101. Right-click the adapter used and select the "Properties" command from the shortcut menu. Figure 6-13 Selecting properties 102. Select the "Internet Protocol Version 4 (TCP/IPv4)" entry and click the "Properties" button. Figure 6-14 Selecting the Internet protocol Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 73 – Set the check mark for "Use the following DNS server addresses". Preferred DNS server: 192.168.1.1 (In general: The IP address of the LTE module is entered as preferred DNS server) Figure 6-15 Entering Internet protocol properties Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...

  • Page 74: Setting The Ip Address Of The Scalance W774-1

    104. Open the PST. Figure 6-16 PST start page 105. Select the "Set PG/PC Interface" command in the menu bar under "Settings". Figure 6-17 Opening the "PG/PC Interface" settings Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 75 107. Click the " " button in the toolbar to search for a module. The modules are displayed. Figure 6-19 Listed modules 108. Open the lower-level menu by clicking the "+" symbol and select the menu entry "Ind. Ethernet interface". Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 76 – As IP address, enter the IP address of the LTE module (here: 192.168.1.1). Figure 6-20 Entering the Ind. Ethernet interface field 110. Click the "Load" button and confirm the subsequent dialog with "Yes". 111. Close the PST. Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...

  • Page 77: Configuring The Scalance W774-1

    (192.168.1.20) in the browser. 114. Log in with the following entries: – Name: admin – Password: admin Figure 6-21 Password input You are prompted to change the default password. Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...

  • Page 78: Loading Firmware

    118. Check the version of the firmware under "Information > Versions". 119. You will find the latest firmware on the Internet (https://support.industry.siemens.com/cs/ww/en/ps/6GK5774-1FX00-0AA0). 120. Download the most recent firmware and extract the download. Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 79 6.5 Configuring the SCALANCE W774-1 121. Select the "HTTP" tab under "System > Load&Save" and download the new firmware. Figure 6-23 Loading the firmware update 122. Perform a restart after the loading process. Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...

  • Page 80: Making Settings In The Wizard

    123. Run through the wizard. – Select the user country in the "Country" tab under "Country Code". The selected user country determines the availability of channels. Figure 6-24 Selecting the user country Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 81 192.168.1.1. Figure 6-25 Checking IP addresses 125. In the "Management Interfaces" tab, set the check mark for "SSH Server" and disable the "Telnet Server". Figure 6-26 Selecting the server Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 82 127. To enable the WLAN, set the check mark for "Enabled" in the "Radio" tab. Adapt the send power to the provisions applicable in your country. "Allowed" must appear under "Tx Power Check". Figure 6-28 Enabling the WLAN Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 83 CONNECT 400 will not be available in the WLAN. Figure 6-29 Selecting the channel 129. In the "AP" tab, enter the desired WLAN name next to the port setting under "SSID". Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 84 130. In the "Security" tab, select the "Authentication Type" "WPA2-PSK". Assign a password under "WPA(2) Pass Phrase" and repeat the entry under "WPA(2) Pass Phrase Confirmation". The password is the network key for WLAN access. Figure 6-30 Password/network key assignment Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 85 132. So that the system time remains current even after a restart, configure the system time under "System > System Time" in the "NTP Client" tab. The manual time setting in the "Manual Settings" tab is reset after a restart. Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...

  • Page 86: Commissioning The Router Kit Lan / Lte

    LTE module (default IP of the LTE module is 192.168.1.1). ● You require administrator rights to download the PST. ● You need a ready-for-use LAN adapter to set the IP address. Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 87 Opening the Network and Sharing Center 5. Select the "Change adapter settings" option. 6. Right-click the adapter used and select the "Properties" command from the shortcut menu. Figure 7-2 Selecting properties Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 88 7 Commissioning the Router Kit LAN / LTE 7.2 Setting up interfaces 7. Select the "Internet Protocol Version 4 (TCP/IPv4)" entry and click the "Properties" button. Figure 7-3 Selecting the Internet protocol Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...

  • Page 89: Configuring Scalance M876-4

    7.3.1 Logging in to the Web-based Management Tool Procedure 9. Commission the device. 10. To log in to the Web-based Management Tool, enter the IP address of the LTE module (192.168.1.1) in the browser. Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 90 – Password: admin Figure 7-5 Password input You are prompted to change the default password. 12. Change the password. Figure 7-6 Changing the password 13. Close the Web-based Management Tool. Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...

  • Page 91: Loading Firmware

    16. If the firmware does not have the most recent version, proceed as follows: 17. You will find the latest firmware on the Internet (https://support.industry.siemens.com/cs/ww/en/ps/6GK5876-4AA00-2BA2/dl). 18. Download the most recent firmware and extract the download. Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 92 7.3 Configuring SCALANCE M876-4 19. Select the "HTTP" tab under "System > Load&Save" and download the new firmware. Figure 7-8 Loading the firmware 20. Perform a restart after the loading process. Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...

  • Page 93: Making Settings In The Wizard

    23. In the "SIM" tab, enter the PIN of the SIM card, remove the check mark for "Enable Mobile Network Interface" and set the check mark for "Allow Data Roaming". Figure 7-10 Entering the PIN of the SIM card Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 94 24. In the "Operator" tab, select the network provider with a check mark in the "Enabled" column. If the desired network provider is not in the table, select the network provider via the "Country List" and "Provider List". Figure 7-11 Selecting the network provider Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 95 7.3 Configuring SCALANCE M876-4 25. In the "Time" tab, set the check mark for "NTP Client" and enter the address "de.pool.ntp.org" under "NTP Server Address". Figure 7-12 Time setting Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 96 7 Commissioning the Router Kit LAN / LTE 7.3 Configuring SCALANCE M876-4 26. Check your settings in the "Summary" tab and click "Set Values". Figure 7-13 Wizard summary Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 97 27. The status "Registered to home network (network strength)" is displayed on the start page under "Connection Status". If this status is not displayed, check the connection of the antenna cable and click "Refresh". Figure 7-14 SCALANCE M876-4 start page Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...

  • Page 98: Configuring A Firewall

    "Changes will be saved automatically in 60 seconds. Press "Write Startup Config" to save immediately" and then on "Write Startup Config". 7.3.5 Updating the DHCP server Procedure 32. Switch to the menu "System > DHCP". Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...
  • Page 99 Lower and Upper Address. Make sure to stay in the same subnet (192.168.1.x). Figure 7-16 Setting the DHCP server 34. In the "DHCP Options" tab, make the settings as shown in the figure. Figure 7-17 Setting the DHCP options Application example for SIMOTICS CONNECT 400 - Router KitInbetriebnahme- und Montagehandbuch...

  • Page 100: Appendix

    Industry Online Support Do you have any questions or need assistance? Siemens Industry Online Support offers round the clock access to our entire service and support know-how and portfolio. The Industry Online Support is the central address for information about our products, solutions and ser- vices.

  • Page 101: Industry Mall

    8.2 Industry Mall 8.2 Industry Mall Die Siemens Industry Mall ist die Plattform, auf der das gesamte Produktportfolio von Siemens Industry zu- gänglich ist. Von der Auswahl der Produkte über die Bestellung und die Lieferverfolgung ermöglicht die In- dustry Mall die komplette Einkaufsabwicklung – direkt und unabhängig von Zeit und Ort: mall.industry.siemens.com...

Table of Contents