Sony SNC-WR632C Service Manual
  1. Manuals
  2. Brands
  3. Sony Manuals
  4. Security Camera
  5. SNC-WR632C
  6. Service manual

Sony SNC-WR632C Service Manual

Hide thumbs Also See for SNC-WR632C:
Table of Contents

Advertisement

Quick Links

NETWORK CAMERA
SNC-WR632C
SNC-WR602C
SERVICE MANUAL
1st Edition

Advertisement

Table of Contents
loading

Related Manuals for Sony SNC-WR632C

Summary of Contents for Sony SNC-WR632C

  • Page 1 NETWORK CAMERA SNC-WR632C SNC-WR602C SERVICE MANUAL 1st Edition...
  • Page 2 LAN connector   Follow the instructions for the above port. WARNUNG Beim Einbau des Geräts ist daher im Festkabel ein leicht zugänglicher Unterbrecher einzufügen, damit sich bei einer Funktionsstörung die Stromversorgung zum Gerät jederzeit unterbrechen läßt. SNC-WR632C/WR602C...

  • Page 3: Table Of Contents

    Notes on Replacing the SY-416 Board ......2-1 (E) 2-1-1. Connection Diagram ........2-1 (E) 2-1-2. Replacing of Mac Address Label .....2-2 (E) 7. Frame Wiring 2-1-3. Mac Address and Serial Number Writing ..2-2 (E) 2-1-4. Firmware Version Upgrade ......2-7 (E) Frame Wiring..............7-1 1 (E) SNC-WR632C/WR602C...

  • Page 4: Manual Structure

    Manual Structure Purpose of this manual This manual is the Service Manual of the Network Camera SNC-WR632C/ WR602C. This manual describes the information on the premise of providing the block level service (such as service overview, adjustment and procedure when replacing the boards, troubleshooting, circuit description, spare parts, block diagrams, and frame wiring).

  • Page 5: Service Overview

    1.20 ?0.15 N.m (12.2 ?1.5 kgf.cm) . Hexagon socket bolt (M6 x 15): 5.20 ?0.78 N.m (53.0 ?7.9 kgf.cm) When using the torque driver with the notation of cN.m, interpret it as follows. Example: 0.8 N.m = 80 cN.m 1-1 (E) SNC-WR632C/WR602C...

  • Page 6: Removing/Installing The Cabinet

    PSW4 Marks Sunshade 3. To install, reverse the removal procedure. When attaching, align the mark on the top sunshade assembly with the mark on the sunshade, and rotate the top sunshade assembly in the counterclockwise direction (3). 1-2 (E) SNC-WR632C/WR602C...

  • Page 7: Dome Cover Assembly

    1-3-2. Dome Cover Assembly 1. Loosen the six screws (with drop-safe), then remove the dome flange. 2. Remove the O-ring (DOME). Screws (with drop-safe) Screws (with drop-safe) Dome flange O-ring (DOME) 1-3 (E) SNC-WR632C/WR602C...
  • Page 8 3. Remove the six screws, then remove the dome cover holder and dome cover assembly. 4. Remove the rubber packing (dome) from the dome cover assembly. PSW3 Dome cover holder Dome cover assembly Rubber packing (dome) 1-4 (E) SNC-WR632C/WR602C...
  • Page 9 Out cabinet O-ring (DOME) Out cabinet Rib faces upward Dome cover assembly Dome flange Dome cover holder c’ c’ b’ b’ a’ a’ Tighten the screws evenly in diagonal direction. Tighten the screws evenly in diagonal direction. 1-5 (E) SNC-WR632C/WR602C...

  • Page 10: Sunshade

    3. Remove the top unit assembly in the directions of the arrows A and B. 4. Remove the four screws (PSW4 x 10), then remove the sunshade. 5. Remove the O-ring (TOP). Hexagon socket bolts Top unit assembly PSW4 Sunshade O-ring (TOP) 1-6 (E) SNC-WR632C/WR602C...
  • Page 11 Top unit assembly TM-61 board Portion A Connectors Portion B Wire (O) IF-1232 board Out cabinet Convex portion Fig. 4 O-ring (TOP) Out cabinet Groove Fig. 2 Back side of top unit assembly Cover (TM) Connector TM-61 board 1-7 (E) SNC-WR632C/WR602C...

  • Page 12: Removing/Installing The Main Parts

    3. Remove the two screws, then remove the TM cover. 4. Remove the two screws, then remove the TM-61 board in the direction of the arrow. PSW2.6 TM cover PSW2.6 TM-61 board 5. To install, reverse the removal procedure. 1-8 (E) SNC-WR632C/WR602C...

  • Page 13: If-1232 Board

    5. Remove the two step screws, then remove the IF-1232 board. 6. Disconnect the harness from the connector (CN702) on the IF-1232 board. PSW2.6 Top plate Flexible flat cables Step screws CN703 IF-1232 board CN702 CN704 Harness 7. To install, reverse the removal procedure. 1-9 (E) SNC-WR632C/WR602C...

  • Page 14: Tilt Block

    2. Remove the three screws, then remove the top plate. 3. Disconnect the two flexible flat cables from the connectors (CN703 and CN704) on the IF-1232 board. PSW2.6 Top plate Flexible flat cables IF-1232 board CN704 CN703 1-10 (E) SNC-WR632C/WR602C...
  • Page 15 4. Disconnect the five harnesses from the connectors (CN5002, CN5501, CN5502, CN5505 and CN5506) on the HC-51 board. 5. Remove the four screws, then remove the TILT block. TILT block PSW2.6 CN5505 HC-51 board CN5002 CN5501 CN5502 Harnesses CN5506 Harnesses 6. To install, reverse the removal procedure. 1-11 (E) SNC-WR632C/WR602C...

  • Page 16: Heater Unit Assembly And Dc Fan (Sirocco, 12 V)

    DC fan (sirocco, 12 V) Cable clamp Fan bracket Out cabinet 8. To install, reverse the removal procedure. When attaching the DC fan (sirocco, 12 V), attach it with the label side faced toward the out cabinet. 1-12 (E) SNC-WR632C/WR602C...

  • Page 17: Board

    3. Disconnect the harness and flexible flat cable from the connectors (CN5001 and CN5701) on the HC-51 board. 4. Remove the four screws, then remove the HC-51 board. PSW2.6 CN5001 Harness HC-51 board Flexible flat cable CN5701 5. To install, reverse the removal procedure. 1-13 (E) SNC-WR632C/WR602C...

  • Page 18: Board

    SY-416 board Harnesses CN104 CN103 CN105 CN107 CN101 Harness CN902 Flexible SY-416 board flat cable Twist the slip ring harness three turns and rout it as shown in the illustration. Capacitor 9. To install, reverse the removal procedure. 1-14 (E) SNC-WR632C/WR602C...

  • Page 19: Board

    6. Disconnect the three harnesses from the connectors (CN2002, CN2003 and CN2501) on the PS-858 board. 7. Remove the radiation sheet (trans) from the PS-858 board. Harnesses Radiation sheet (trans) PS-858 board CN2003 CN2002 CN2501 Bottom side 8. To install, reverse the removal procedure. 1-15 (E) SNC-WR632C/WR602C...

  • Page 20: Dc Fan

    5. Remove the hook (G), then remove the side cabinet (right). 6. Remove the side cabinet (left) in the same procedure as steps 3 to 5. Side cabinet (left) Portion D Hook (G) Hook (F) Portion A Hook (C) Side cabinet (right) 1-16 (E) SNC-WR632C/WR602C...
  • Page 21 Left side view Right side view Lens Lens Screws Screws Camera cabinet Hook (upper) Camera block After the camera block is rotated, the stepping motor assembly is positioned as shown in this illustration. Hook Camera cabinet (lower) Hook Hook 1-17 (E) SNC-WR632C/WR602C...
  • Page 22 13. To install, reverse the removal procedure. . Attach the DC fan with the label side facing the direction as shown in the illustration. . Route and connect the harness of the DC fan through the notch. 1-18 (E) SNC-WR632C/WR602C...

  • Page 23: Cn-3521 Board

    6. Remove the two screws, then remove the CN-3521 board. Harness BTP2.6 CN904 CN-3521 board CN902 CN908 Fine-wire coaxial cable Place the cable with the contact side facing upward. CN907 Flexible flat cables Fine-wire coaxial cable 7. To install, reverse the removal procedure. 1-19 (E) SNC-WR632C/WR602C...

  • Page 24: Fcb Assembly

    6. Remove the four screws (PSW2 x 6), then remove the FCB assembly. 7. Disconnect the flexible flat cable from the connector on the FCB assembly. PSW2 FCB assembly Connector Flexible flat cable Front cabinet 8. To install, reverse the removal procedure. 1-20 (E) SNC-WR632C/WR602C...

  • Page 25: Center Cabinet

    7. Remove the four screws, then remove the two center cabinets. Center cabinet FCB holder After the FCB holder is rotated, the stepping motor assembly is positioned as shown in this illustration. Center cabinet 8. To install, reverse the removal procedure. 1-21 (E) SNC-WR632C/WR602C...
  • Page 26 The connector on the stepping motor assembly (PAN) and the connector (CN401) on the MD-151 board are marked with black paint, and the connector on the stepping motor assembly (TILT) and the connector (CN501) on the MD-151 board are marked with blue paint. 1-22 (E) SNC-WR632C/WR602C...

  • Page 27: Board

    7. Disconnect the harness from the connector (CN103) on the MD-151 board. Fine-wire coaxial cable TILT block assembly Place the cable with the contact side facing front side. Fine-wire coaxial cable Harness Black paints Harness CN401 CN102 CN501 CN103 Harness CN101 Blue paints MD-151 board Flexible flat cable 1-23 (E) SNC-WR632C/WR602C...
  • Page 28 TILT motor harness harness CN101 BTP2.6 Flexible flat (Screw b) cable Bottom side MD-151 board CN102 Slip ring harness and TILT motor harness 10. Assemble this unit in the reverse order of steps 1 to 3 in “Removal”. 1-24 (E) SNC-WR632C/WR602C...

  • Page 29: Fcb Holder

    . When attaching the timing belt, push it against the guide of the TILT pulley. Guide FCB holder TILT pulley Timing belt Timing belt TILT bearing holder (L) TILT bearing holder (R) Flexible flat cable Flexible flat cable Stepping motor assembly (TILT) TILT bearing holder (R) Screws Stepping motor assembly (TILT) 1-25 (E) SNC-WR632C/WR602C...
  • Page 30 Hooks TILT harness guide Hooks TILT pulley TILT shaft assembly Flexible flat cable FCB holder Wrap the flexible flat cable 3 and 1/4 turns. Ball bearing (L-1680) TILT bearing plate 16. To install, reverse the removal procedure. 1-26 (E) SNC-WR632C/WR602C...

  • Page 31: Stepping Motor Assembly (Tilt)

    (TILT), then fully tighten the screws while pushing it in the direction of the arrow. . Attach the stepping motor assembly (TILT) so that the tension of its timing belt is the same as that of the stepping motor assembly (PAN). 1-27 (E) SNC-WR632C/WR602C...

  • Page 32: Slip Ring Assembly (G6)

    13. Remove the three screws, then remove the PAN plate (O). PSW2.6 PAN harness guide FCB holder After the FCB holder is rotated, the stepping motor assembly is positioned as shown in this illustration. Stepping motor assembly (PAN) TILT chassis Screws PAN plate (O) PSW2.6 1-28 (E) SNC-WR632C/WR602C...
  • Page 33 15. Remove the two screws, then remove the PAN shaft assembly and timing belt. 16. Remove the three screws, then remove the PAN pulley. PSW2.6 PSW2.6 Hole TILT chassis Timing belt PAN pulley PAN shaft assembly Boss PAN shaft assembly 1-29 (E) SNC-WR632C/WR602C...
  • Page 34 . When attaching the timing belt, rotate the PAN pulley five times in the direction of the arrow so that the timing belt comes in contact with the guide of the PAN pulley. PAN pulley Guide PAN pulley Timing belt Timing belt 1-30 (E) SNC-WR632C/WR602C...

  • Page 35: Stepping Motor Assembly (Pan)

    11. Remove the PAN plate (0) and timing belt. (Refer to steps 11 to 15 in Section 1-4-15.) 12. Remove the two screws, then remove the stepping motor assembly (PAN). Stepping motor assembly (PAN) Stepping motor assembly (PAN) TILT chassis Screws PSW3 1-31 (E) SNC-WR632C/WR602C...

  • Page 36: Lead-Free Solder

    . The ordinary soldering iron can be used but the iron tip has to be applied to the solder joint for a slightly longer time. The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful. 1-32 (E) SNC-WR632C/WR602C...

  • Page 37: Adjustment And Procedure When Replacing The Boards

    Color video monitor termination When using 24 VAC power supply (rating: 80 W or more) Power supply 24 VAC power supply (rating: 80 W or more) Camera Power cable LAN cable Personal computer Color video monitor termination 2-1 (E) SNC-WR632C/WR602C...

  • Page 38: Replacing Of Mac Address Label

    . Latest SNC toolbox Downloadable from the following URL. http://www.sony.net/ipela/snc . Mac/Serial writing tool: J-7121-430-A . Power supply for this unit: 24 VAC power supply (rating: 80 W or more) or HPoE + Hub (Powerdsine PD-9501G or equivalent) 2-2 (E) SNC-WR632C/WR602C...
  • Page 39 The information of this unit is displayed. If it is not displayed, click the [Search] button. [Search] button Information is displayed for each model. Double-click this portion. 6. Double-click the information display portion of this unit. The viewer screen is displayed. [Setting] button 2-3 (E) SNC-WR632C/WR602C...
  • Page 40 When there is a date/time deviation by one day or more, correctly set the date and time of PC. (Refer to the User’s Guide.) 12. Double-click “G6 Serial_Inputter For Service.exe”. “G6 Serial_Inputter For Service.exe” is started. [START] button 2-4 (E) SNC-WR632C/WR602C...
  • Page 41 The MAC address should be the same as the one indicated on the MAC address label attached to the SY-416 board. 3. Type the serial number and select the destination of this unit. Serial number [OK] button Destination 2-5 (E) SNC-WR632C/WR602C...
  • Page 42 6. Check the above message, and then click the [YES] button. The writing of serial number is started. When the writing of the serial number and destination is completed, the NLSS flag check is automati- cally performed. NLSS flag confirmation message 2-6 (E) SNC-WR632C/WR602C...

  • Page 43: Firmware Version Upgrade

    . Latest update firmware . Latest SNC toolbox Downloadable from the following URL. http://www.sony.net/ipela/snc . Power supply for this unit: 24 VAC power supply (rating: 80 W or more) or HPoE + Hub (Powerdsine PD-9501G or equivalent) 2-7 (E) SNC-WR632C/WR602C...
  • Page 44 Information is displayed for each model. Double-click this portion. Upgrade 1. Click the information display portion of this unit, then click the [Network] button. The Device Account screen is displayed. Administrator name and Administrator password [OK] button 2-8 (E) SNC-WR632C/WR602C...
  • Page 45 When the setting is normally completed, the Information screen is displayed. If an error is displayed, check the connection of the LAN cable between this unit and PC, and then perform the procedure from step 1 again. [OK] button 2-9 (E) SNC-WR632C/WR602C...
  • Page 46 4. Click the [OK] button. [Upgrade] button 5. Click the [Upgrade] button. The Firmware Upgrade screen is displayed. Select the latest firmware. [Browse] button [Start|Upgrading] button 2-10 (E) SNC-WR632C/WR602C...
  • Page 47 Therefore, be sure to perform the version upgrade twice with the latest firmware. 8. After the completion of the version upgrade, check that the MAC address, serial number and firm- ware version displayed in the SNC toolbox are correct. Firmware version (Version No.) Mac address Serial number (Serial No.) 2-11 (E) SNC-WR632C/WR602C...
  • Page 48 10. Click “Initialize” of “System”, and then click the [Factory|default] button. The Warning screen is displayed. [Yes] button 11. Click the [Yes] button. Completion 1. Exit out of SNC toolbox. 2. Turn off the power and disconnect the connection of each equipment. 2-12 (E) SNC-WR632C/WR602C...

  • Page 49: Troubleshooting

    Check if there is any abnormality in the cooling fan inside of this unit immediately. . FAN ALARM is displayed on the viewer screen. (It disappears after a specified period of time.) . A mail to notify the abnormality of fan is delivered to the registered administrator of this unit. 3-1 (E) SNC-WR632C/WR602C...

  • Page 50: Power Trouble

    Does a voltage at pin 8 of CN2501 on the PS-858 board Replace the SY-416 board. become 3.3 V a little later after (Refer to Section 1-4-6.) the power is turned on? Replace the PS-858 board. (Refer to Section 1-4-5.) 3-2 (E) SNC-WR632C/WR602C...

  • Page 51: Pan/Tilt Trouble

    MD-151 board, or the output correctly? peripheral circuit 16 VDC, 5 VDC, 3.3 VDC Failure of the microcontroller (IC301) on the MD-151 board or the peripheral circuit. Replace the defective parts or MD-151 board. (Refer to Section 1-4-12.) 3-3 (E) SNC-WR632C/WR602C...

  • Page 52: Tilt Trouble

    Is there any problem with the connection of the tilt motor Connect the pan motor correctly. that is connected to CN401 on the MD-151 board? Failure of the drive circuit portion of the pan motor on the MD-151 board 3-4 (E) SNC-WR632C/WR602C...

  • Page 53: Image Trouble

    The video monitor does not display the image. (Go to page 3-6 A.) Check the defective portion. Neither video monitor nor PC monitor displays the image. (Go to page 3-6 B.) The PC monitor does not display the image. Go to “3-5. Network Trouble”. 3-5 (E) SNC-WR632C/WR602C...
  • Page 54 Connect CN103 on the MD-151 pins 5 to 7 of CN105 on the board with CN105 on the SY-416 SY-416 board? board. 7 pin: Component Y signal tri-level sync signal Replace the SY-416 board. (Refer to Section 1-4-6.) 3-6 (E) SNC-WR632C/WR602C...

  • Page 55: Network Trouble

    4. Set the reset switch (S802) on the from the following URL. TM-61 board to OFF. http://www.sony.net/ipela/snc Is the symptom improved? Reconfigure the camera settings. Uninstall Active x. Is the symptom improved? Reconfigure the camera settings. Replace the SY-416 board. (Refer to Section 1-4-6.) 3-7 (E) SNC-WR632C/WR602C...

  • Page 57: Circuit Description

    The CN-3521 board relays an FCB camera block and MD-151 board. The CN-3521 board also mounts a temperature sensor. 4-1-7. HC-51 Board The HC-51 board controls an internal temperature by driving of a heater and generates the driving voltage of an internal fan. 4-1 (E) SNC-WR632C/WR602C...
  • Page 58 Analog video input circuit block The video signal output from an FCB camera block is input from CN101. In SNC-WR632C and SNC-WR602C, the contents of the video signal are as described below. SNC-WR632C The Y, Pb, and Pr analog component signals and Y signals of 1080/60P and 1080/50P or 1080/30P and 1080/25P are composite signals obtained from a tri-level sync signal.
  • Page 59 SoC controls the extended I/O connector through an I C bus and turns on and off the relays. As a result, an external connector is turned on when the relays are turned on. This enables the operation of equipment connected to the external connector. 4-3 (E) SNC-WR632C/WR602C...
  • Page 60 Local power block The constant voltages (1.1 V, 1.5 V, 2.5 V, 1.8 V, and 3.3 V) used on an SY-416 board are generated on the SY-416 board using a voltage of 5 VDC output from a PS-858 board. 4-4 (E) SNC-WR632C/WR602C...
  • Page 61 When the power of this unit is turned on, in the initial state, a voltage of 24 VDC on the PS-858 board is in an OFF state. During start of this unit, 24 VDC is turned on and the power to a drive system and camera block is turned on. 4-5 (E) SNC-WR632C/WR602C...
  • Page 62 The pan and tilt motors are distinguished for reasons of characteristics. Data that varies for each motor is written in the microcontroller (IC301) on an MD-151 board. Therefore, do not change the combination of the MD-151 board and motor. 4-6 (E) SNC-WR632C/WR602C...

  • Page 63: Board

    12 VDC using a DC/DC converter by IC5002. 9 VDC is generated from 12 VDC using series regulator Q5503 of 12 VDC. IC5003 is a DC/DC converter that generates 24 VDC. During feeding of 24 VAC, it is in a stop state. 4-7 (E) SNC-WR632C/WR602C...
  • Page 64 A reset switch (S802) is used to return a system to the factory-setting state. An internal parameter is set to the factory-setting state when the power is turned on after S802 is switched to the reset position. After reset, return the internal parameter to the ordinary position. 4-8 (E) SNC-WR632C/WR602C...

  • Page 65: Spare Parts

    Therefore, specified parts should be used in the case of な部品です。したがって，交換する時は必ず指定 replacement. の部品を使ってください。 2. Standardization of Parts 2.  部品の共通化 Some repair parts supplied by Sony differ from those   ソニーから供給する補修用部品は，セットに使われて used for the unit. These are because of parts common- いるものと異なることがあります。 ality and improvement.

  • Page 66: Exploded Views

    Top Sunshade Block 5-2. Exploded Views Arrow B view PSW2.6 PSW2.6 SNC-WR632C/WR602C...
  • Page 67 3-869-367-51 s SET SCREW(M4 PSW) 4-159-350-11 s BOLT,HEXAGON SOCKET (M6X15) 4-159-357-11 s SCREW, HOOK 4-455-937-01 s PACKING (COUPLING), RUBBER 4-455-950-02 s SHADE,SUN 4-455-983-01 s SCREW,+PSW M3X6(SUS) 4-455-984-01 s SCREW,6SSF M6X12(SUS) 4-454-702-01 s SW COVER 4-476-447-01 s COVER, TM 7-621-759-45 s +PSW, 2.6X6 SNC-WR632C/WR602C...
  • Page 68 SP Description A-2061-622-A s MOUNTED CIRCUIT BOARD, IF-1232 A-1971-133-A s DOME COVER ASSY 4-155-909-01 s SCREW, STEP 4-159-358-11 s SCREW, FLANGE 4-455-906-02 s FLANGE, DOME 4-455-909-01 s PACKING(DOME), RUBBER 4-455-969-01 s O-RING(TOP) 4-455-983-01 s SCREW,+PSW M3X6(SUS) 7-621-759-45 s +PSW, 2.6X6 SNC-WR632C/WR602C...
  • Page 69 To HC-51 board PSW2.6 PSW2.6 To HC-51 board Part No. SP Description A-1923-468-A s HEATER UNIT ASSY 1-855-289-11 s FAN, DC (SIROCCO, 12V) 2-580-604-01 s SCREW, +PSW M4X20 3-669-607-22 s +PSW (SMALL ROUND) (2.6) 4-455-970-01 s O-RING(DOME) 7-621-759-45 s +PSW, 2.6X6 SNC-WR632C/WR602C...
  • Page 70 Boards Block To IF-1232 board To DC fan To Heater unit To DC fan To Heater unit PSW2.6 To IF-1232 board SNC-WR632C/WR602C...
  • Page 71 1-846-575-11 s CABLE, FLEXIBLE FLAT (30P) 1-846-576-11 s CABLE, FLEXIBLE FLAT (20P) 1-969-379-11 s HARNESS, SUB (6P/IF-HC) 1-969-380-11 s HARNESS, SUB (14P/PS-SY) 1-969-381-11 s HARNESS, SUB (10P/HC-PS) 1-969-837-11 s HARNESS, SUB (4P/PS-SY) 4-296-000-11 s SHEET, RADIATION (TRANS) 7-621-759-45 s +PSW, 2.6X6 SNC-WR632C/WR602C...
  • Page 72 Cabinet Block Part No. SP Description 3-863-696-01 s +BSW M2 4-472-126-02 s CABINET, SIDE 4-472-128-01 s CABINET, CAMERA 4-472-129-01 s CABINET, FRONT 7-685-534-14 s SCREW +BTP 2.6X8 TYPE2 N-S SNC-WR632C/WR602C...
  • Page 73 1-846-943-11 s CABLE, CONNECTOR COAXIAL 10P 7-685-534-14 s SCREW +BTP 2.6X8 TYPE2 N-S 7-685-650-99 s SCREW +BVTP 3X16 TYPE2 TT(B) 1-855-276-11 s FAN, DC (40 SQUARE) 4-471-367-01 s PLATE, TILT BEARING 4-471-368-01 s BELT, TIMING 4-472-120-02 s HOLDER, FCB 4-472-121-01 s PULLEY, TILT SNC-WR632C/WR602C...
  • Page 74 4-471-368-01 s BELT, TIMING PSW2.6 X-2587-783-1 s SHAFT ASSY, PAN 1-492-632-11 s ASSY,SLIP RING(G6) 4-382-854-01 s SCREW (M3X8), P, SW (+) 4-471-365-02 s PULLEY, PAN 4-472-130-01 s SHUTTER, PAN 7-621-759-45 s +PSW, 2.6X6 7-685-534-14 s SCREW +BTP 2.6X8 TYPE2 N-S 5-10 SNC-WR632C/WR602C...

  • Page 75: Packing Materials & Supplied Accessories

    SIMPLIFIED CHINESE) 4-441-096-03 s CD-ROM USERS GUIDE (SNC EASY IP SETUP) (JAPANESE, ENGLISH, FRENCH, SPANISH, GERMAN, ITALIAN, SIMPLIFIED CHINESE, PORTUGUESS, RUSSIAN, KOREAN) 4-455-968-01 s MOUNT,PUSH *1 4-456-192-02 s COUPLING (CN) *1 4-456-193-01 s O-RING (COUPLING) 4-646-805-01 s CRAMP 5-11 SNC-WR632C/WR602C...

  • Page 77: Block Diagrams

    DETECTION DETECTION CONTROL SLOT RELAY RELAY TRANS IC2502 CIRCUIT CIRCUIT CIRCUIT IC2001 RY5501 RY5501 5.2V IDEAL DIODE AC24V/DC12V DC/DC (1/2) (2/2) BRIDGE RY5502 POWER CONTROLLER (2/2) RELAY PS-858 CN1003 HC-51 CN5506 CN5501 CN5502 CN5505 HEATER1 HEATER2 FAN1 FAN2 Overall SNC-WR632C/WR602C...

  • Page 79: Frame Wiring

    MIC/LINE IN CN806 LINE OUT CN111 TOOL CN805 CN904 CN501 CN401 CN105 CN704 TILT MOTOR MOTOR CN803 CN5701 CN902 CN5505 HEATER1 CN5506 CN903 HEATER2 CN5501 CN103 CN104 FAN1 CN5502 CN5001 CN1003 CN2501 CN2002 FAN2 CN702 CN5002 PS-858 HC-51 Frame Wiring SNC-WR632C/WR602C...
  • Page 82 SNC-WR602C (CN) SNC-WR602C (SY) SNC-WR632C (CN) Printed in Japan Sony Corporation SNC-WR632C (SY) J, E 2014. 8 32 9-878-596-01 ©2014...

This manual is also suitable for:

Snc-wr602c

Table of Contents