Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Xilinx FMC XM104
Summary of Contents for Xilinx FMC XM104
- Page 1 FMC XM104 Connectivity Card User Guide UG536 (v1.1) September 24, 2010...
-
Page 2: Revision History
Xilinx. Xilinx expressly disclaims any liability arising out of your use of the Documentation. Xilinx reserves the right, at its sole discretion, to change the Documentation without notice at any time. Xilinx assumes no obligation to correct any errors contained in the Documentation, or to advise you of any corrections or updates. -
Page 3: Table Of Contents
Silicon Labs Si5368 ............19 FMC XM104 Connectivity Card User Guide www.xilinx.com... - Page 4 FMC XM104 Connectivity Card User Guide UG536 (v1.1) September 24, 2010...
-
Page 5: Preface: About This Guide
• Intellectual Property: www.xilinx.com/ipcenter The XM104 can be used with Xilinx FMC high pin count (HPC) boards and, with limited functionality, FMC low pin count (LPC) boards. Board documentation, schematics and PCB design files are available at www.xilinx.com/fmc. Additional Support Resources To find additional documentation, see the Xilinx website at: www.xilinx.com/support/documentation/index.htm... - Page 6 Preface: About This Guide www.xilinx.com FMC XM104 Connectivity Card User Guide UG536 (v1.1) September 24, 2010...
-
Page 7: Chapter 1: Xm104
EK-V6-ML605-G Notes: While every effort has been made to comply with the FPGA Mezzanine Card Specification, Xilinx cannot claim nor assume full compliance with the FMC/VITA-57-1 specification. Consequently, Xilinx cannot claim nor support the usage of the XM104 on any other FMC (VITA-57.1) board. -
Page 8: Software
XM104. Hand tighten the two mounting screws to the bottom of the board. Turn the attached board and XM104 unit over such that the Xilinx FPGA is visible. Connect the input power source to the board. Turn the board power input switch to The system is now ready for use. -
Page 9: Technical Support
UG536_01_111609 Figure 1-1: Installation of XM104 to Board FMC HPC Connector Technical Support Xilinx offers technical support for this product only when used in conjunction with boards listed in Table 1-1. For assistance with the XM104 and Xilinx boards, contact Xilinx for technical support at www.xilinx.com/support. -
Page 10: Board Technical Description
DP4-DP7 10GE Base-CX4 J2 Clock Clock 156.25 MHz Driver MGT Data Ports 8-9 DP8-DP9 Switch Electrical Loopback 2 K b EEPROM GBTCLK1_M2C UG536_02_120309 Figure 1-2: XM104 Block Diagram www.xilinx.com FMC XM104 Connectivity Card User Guide UG536 (v1.1) September 24, 2010... -
Page 11: Detailed Description
12. For full functionality, the XM104 must be installed on a board FMC connector supporting high pin count interfaces. X-Ref Target - Figure 1-3 UG536_03_111609 Figure 1-3: XM104 Features FMC XM104 Connectivity Card User Guide www.xilinx.com UG536 (v1.1) September 24, 2010... - Page 12 Silicon Labs Si570 IIC serial bus re-programmable clock source and Clocking circuits Silicon Labs Si5368 any-rate precision clock multiplier and clock jitter attenuator clock source integrated circuits. Notes: 1. VITA 57.1 FMC HPC Connector J1. www.xilinx.com FMC XM104 Connectivity Card User Guide UG536 (v1.1) September 24, 2010...
-
Page 13: Vita 57.1 Fmc Hpc Connector J1
The XM104 uses Samtec FMC HPC connector part number ASP-134488-01. The XM104 connector mates with an FMC connector. See Xilinx board user guides and schematics for a description of features provided by HPC interfaces contained on the board, including power supply specifications, FPGA banking connectivity, and FPGA pin assignments. -
Page 14: Multi-Gigabit Transceiver Data Port 2 - J11 Sata1
Table 1-6: FPGA Multi-Gigabit Transceiver Data Port 3 Connectivity FMC HPC Connector J1 Serial ATA Connector Signal Name DP3_C2M_P DP3_C2M_N DP3_M2C_N DP3_M2C_P Notes: 1. AC coupled using a series 0.1 uF capacitor www.xilinx.com FMC XM104 Connectivity Card User Guide UG536 (v1.1) September 24, 2010... -
Page 15: Multi-Gigabit Transceiver Data Ports [4:7] - J2 10Ge Base-Cx4 Connector
M24C02 component enables E0 and E1. Xilinx boards provide GA0 and GA1 signal strapping to 3.3V and GND signals creating different E0 and E1 chip enable decodes on the E1 and E0 inputs of the EEPROM. -
Page 16: Pca9543 Iic Switch
A1 and A0 of the PCA9543 component. Xilinx boards provide GA0 and GA1 signal strapping to 3.3V and GND signals creating different A0 and A1 address decodes on the PCA9543. - Page 17 The two downstream IIC devices connected to the PCA9543 are at the following IIC addresses: • Si570 IIC address is at 0x5D • Si5368 IIC address is at 0x68 FMC XM104 Connectivity Card User Guide www.xilinx.com UG536 (v1.1) September 24, 2010...
-
Page 18: Clocking Circuits
Power Supply 3.3V IIC Address For additional information on this component, including reprogramming the clock frequency through the IIC serial bus interface, consult the manufacturer's data sheet at: www.silabs.com. www.xilinx.com FMC XM104 Connectivity Card User Guide UG536 (v1.1) September 24, 2010... -
Page 19: Silicon Labs Si5368
Board Technical Description Silicon Labs Si5368 A Silicon Labs Si5368 any-rate precision clock multiplier/jitter attenuator integrated circuit provides a wide range of clocking applications for the Xilinx board and XM104 combination. Table 1-13 shows the connections of the SI5368 differential clock outputs to the XM104 FMC HPC connector. - Page 20 Si5368 registers to re-establish clock outputs. The Si5368 is located at IIC address 0x68. For additional application information on the Si5368 component see the manufacturer's data sheet at www.silabs.com. www.xilinx.com FMC XM104 Connectivity Card User Guide UG536 (v1.1) September 24, 2010...
- Page 21 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Xilinx HW-FMC-XM104-G...