Advertisement
Quick Links
Quick Start Guide
INVENTOR II
SZ15-EN-A02
1. Hot! Avoid touching the heating nozzle in operation.
WARNING
2. Moving parts in printer may cause injury. Do not wear gloves
or other sources of entanglement in operation.
USERGUIDE
The User Guide is in the USB stick.
This guide is only applicable to FLASHFORGE Inventor II 3D printer
Advertisement
Related Manuals for Flashforge Inventor II
Summary of Contents for Flashforge Inventor II
- Page 1 WARNING 2. Moving parts in printer may cause injury. Do not wear gloves or other sources of entanglement in operation. USERGUIDE The User Guide is in the USB stick. This guide is only applicable to FLASHFORGE Inventor II 3D printer...
-
Page 2: Kit Contents
Kit Contents Filament Spool 3D Printer Quick Start Guide After-sales Service Card Power Adapter Power Cable USB Cable USB Stick Unclogging Pin Tool Screwdriver Wrench GREASE Allen Wrench / Grease Solid Glue Filament Guide Tube PTFE Tube... - Page 3 Getting to Know Your Inventor II 3. Filament Cartridge 1. Z-Axis Guide Rod 2. Filament Outlet 4. Filament Inlet 5. Y-Axis Guide Rod 6. X-Axis Guide Rod 7. Touch Screen 8. Touch Screen Button 10. Leveling Knob 11. USB Cable Input 12.
- Page 4 USB stick. 3. Remove all protective foams. 4. Remove the tape on the side. 5. Turn over the Inventor II to remove the tape 6. Remove the top foam piece. in the bottom and all packing bag.
- Page 5 7. Use scissors to cut the buckles that hold the 8. Open the door and take out the lid. rods in the place. 9. Remove the foam on the bottom left. 10. Hold the platform and elevate platform smoothly. 11.
-
Page 6: Hardware Assembly
Hardware Assembly 1. Lift the filament cartridge out from the rear of 2. Insert the filament into the guide tube and Inventor II, where you will place the filament thread the guide tube through the filament spool. outlet. Place the spool of filament in the cartridge. - Page 7 Leveling Build Platform How to change language HOME Filament Level Home Manual Build Preheat Tools Setting Status About 简体中文 Language English English WiFi 日本語 Wlan hotspot 繁體中文 Extruder Calibration Build Plate Leveling Please wait while the extruder and platform finish initial movements... Screw three nuts under the platform anticlockwise until you can’t tighten them any more, then tap [OK] button.
- Page 8 Confirm Are you sure you can’t finger Verifying the distance between nozzle tighten these three knobs any and plate... more? Wait 2. Tap [Yes] if you can’t tighten all the nuts any more, or tap [No] to continue tightening. After tapping [Yes] button, the extruder will move towards the first point and the plate will move up and down to verify the distance between nozzle and plate.
-
Page 9: Loading / Changing Filament
Loading / Changing Filament HOME Filament Level Home Manual Build Preheat Tools Setting Status About 1. Tap [Tools] and then tap [Filament]. I’m heating up... 100% Extruder 61℃ / 220℃ Load Unload 2. Tap [Load]. The extruder will automatically heat up. Once heated, filament will be drawn through the extruder. -
Page 10: First Print
First Print Internal Memory USB Stick Build Preheat Tools 1. Please insert the USB stick into Inventor II. In the print interface, tap [Build]-[USB Stick]. Flashprint切片软件 40mm_Box-PLA Total：0hr 54min 40mm_Box-PLA.gx Build Copy Delete 2. Select [40mm_Box-PLA.gx]. 3. Tap [Build]. 40mm_Box-PLA Extruder 40℃... - Page 11 Scan QR to Get More After-Sales Support After-Sales Service: support@ff3dp.com Tel: +86 579 82273989 Web: www.flashforge.com Add: 2/F, No.518, Xianyuan Road, Jinhua, Zhejiang, China...