Installation; Safety Tips - Monte Carlo Fan Company 5LNR52 D-L Series Owner's Manual

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJUR Y TO PERSONS,
1.
Installation work and electrical wiring must be done b y qualified person(s) in accordance with applicable codes and standards (ANSI/NFP A 70-
1999), including fire-rated construction.
2.
Use this unit only in the manner intended b y the manufacurer. If you have any questions contact the manufacturer.
3.
After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment -grounding conductor on
one side of the outlet box and ungrounded conductor on the other side of the outlet bo x.
4.
Before you begin installing the fan, Switch power off at Service panel and lock service disconnecting means to prev ent power from being
switched on accidentally. When the service disconnecting means cannot be lock ed, securely fasten a prominent warning device, such as a tag,
to the service panel.
5.
Be cautious! read all instructions and safet y information before installing your new fan. Review the accompanying assembly diagrams.
6.
When cutting or drilling into w all or ceiling, do not damage electrical wiring and other hidden utilities.
7.
Make sure the installation site you choose allows the fan blades to rotate without an y obstructions. Allow a minimum clearance of 7 feet from
the floor to the trailing edge of the blade.
8.
To reduce the risk of fire, electric shock, or personal injury , mount to outlet box or supporting system acceptable for fan support. Use only the
screws provided with the outlet box. (Mounting must support at least 35 lbs. (16kg.)).
9.
Do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign object between rotating blades.
10. Attach the mounting bracket using only the hardware supplied with the outlet box.
11.
To reduce the risk of fire or electric shock, do not use this fan with an y solid state fan speed control device, or v ariable speed control.
12.
If this unit is to be installed o ver a tub or shower, it must be marked as appropriate for the application.
13.
NEVER place a switch where it can be reached from a tub or shower .
14.
The combustion airflow needed for safe oper ation of fuel-burning equipment may be affected by this unit's operation. Follow the heating equip-
ment manufacturer's guideline safety standards such as those published b y the National Fire Protection Association (NFP A), and the American
Society for Heating, Refrigeration and Air Conditioning Engineers (A SHRAE) and the local code authorities.
15.
Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prev ent power from being switched
on accidentally. When the service disconnecting means cannot be lock ed, securely fasten a prominent warning device, such as a tag, to the
service panel.
Note - For Outdoor Fans Only: Suitable for use in damp locations when installed in a GFCI protected br anch circuit.
P P h h i i l l l l i i p p s s S S c c r r e e w w d d r r i i v v e e r r
1
Before you begin installing the fan, S witch
power off at Service panel and lock service dis -
connecting means to prevent power from being
switched on accidentally. When the service dis -
connecting means cannot be lock ed, securely
fasten a prominent warning device, such as a
tag, to the service panel.
4
Remove keeper from cross pin and
then cross pin from y oke. Replace
keeper on cross pin and sa ve.

Installation

OBSERVE THE FOLLOWING: READ AND SAVE THESE INSTRUCTIONS
T T O O O O L L S S R R E E Q Q U U I I R R E E D D
W W i i r r e e C C u u t t t t e e r r s s
2
Before installing this fan mak e sure the outlet
box is properly installed to the house structure.
To reduce the risk of fire, electric shock, or per -
sonal injury, mount to outlet bo x or supporting
system acceptable for fan support. (Mounting
must support at least 35 lbs.(16 kg.)).
5
Loosen lock nuts and screws on y oke
till you can not feel screw on inside
of yoke.
S T
AFETY IPS
P P l l i i e e r r s s S S t t e e p p L L a a d d d d e e r r
3
Use metal outlet box suitable for fan support
(must support 35 lbs). Before attaching fan to
outlet box, ensure the outlet bo x is securely
fastened by at least two points to a structur al
ceiling member ( a loose bo x will cause the fan
Use only the screws pro -
to wobble).
vided with the outlet box.
6
Remove 6 yoke screws and save.