Do you have a question about the Connected Charge Station and is the answer not in the manual?
Questions and answers
DAVID HAROLD PRYOR
March 13, 2025
OUR CHARGER WHEN IT RAINS AND IS DAMP WILL NOT CHARGE THE LIGHT NSTAYS YELLOW WHA TDO YOU THINK TH PROB IS/
1 comments:
Mr. Anderson
March 13, 2025
The issue could be that the Ford Connected Charge Station is exposed to moisture, which may affect its operation. The manual states that the charge station should not be installed near water jets, high-pressure cleaners, or garden hoses. If the station is damp and the light stays yellow, moisture might be interfering with its function. To resolve this, ensure the station is installed in a dry location and protected from water exposure. If the problem persists, a qualified electrician should inspect it.
Summary of Contents for Ford Connected Charge Station
Page 1
Ford Connected Charge Station Installation manual 48A Single Phase...
Page 5
0.5 x 3.5 mm 29 mm, 36 mm, T(x)6, T(x)20, T(x)25 40 mm 3 mm (1/8 Inch), 8 mm (3/8 Inch)
Page 6
DIP switch settings.............. 4 5.2.2 Power supply isolation device.......... 4 5.2.3 Dimensioning the lead’s cross-section......4 Step-by-step installation..............5 5.3.1 Required tools..............5 5.3.2 Installing the mounting bracket........5 5.3.3 Removing the front cover..........5 Ford Connected Charge Station Installation manual...
Page 7
- Hazardous voltages are present within the casing. mation, is available through the Ford Connected Charge - The Ford Connected Charge Station does not have its stallation and environmental protection. Station setup app. See also chapter 6.3, "Displaying soft- own power ON/OFF switch.
- Do not install the charge station in the vicinity of water - The initial startup of the charge station must be carried When transporting the Ford Connected Charge Station , jets, such as car wash installations, high-pressure clean- out by a qualified electrician.
In the box Protection class Weight (including 7.95 kg wall mount bracket Scope of delivery for the Ford Connected Charge Station. See table 4. Residual current de- & charging cable) See Fig. 19 on the inside of the back cover.
48 A, 60A CB maximum charging current that you can configure. The type CAUTION 48 A, 60A CB label on the Ford Connected Charge Station is located on The wire colors shown in the illustrations the right. 48 A, 60A CB are for example purposes only.
Page 11
5. Use a Torx T25 screwdriver and four screws (6 x 90 For floor-facing installations of the grid cable, use a ¾“ You need the tools in the following table to install the Ford mm) (¹/₄ x 3¹/₂ inch) to secure the bracket.
Page 12
If you are using a rigid lead, then bend the individual Position the cable in such a way that the cable clamp To connect the grid cable to the Ford Connected Charge Sta- wires, while observing the minimum bend radiuses to area is fully covered by the cable jacket.
Page 13
Download the FordPass™ app, this will be used to con- CAUTION NOTICE nect your Ford Connected Charge Station to your Ford- Make sure that you secure the front cover in such a way Pass account. You must mount the dock holder so that the lowest that it cannot fall while you are fixing the screws.
2. Electrically disconnect the charge station. The Ford Connected Charge Station was developed, manu- lide with it. 3. Dispose of the Ford Connected Charge Station in accor- factured, tested, and supplied in accordance with the The legal requirements for electrical installations, dance with local and national rules and regulations.
Need help?
Do you have a question about the Connected Charge Station and is the answer not in the manual?
Questions and answers
OUR CHARGER WHEN IT RAINS AND IS DAMP WILL NOT CHARGE THE LIGHT NSTAYS YELLOW WHA TDO YOU THINK TH PROB IS/
The issue could be that the Ford Connected Charge Station is exposed to moisture, which may affect its operation. The manual states that the charge station should not be installed near water jets, high-pressure cleaners, or garden hoses. If the station is damp and the light stays yellow, moisture might be interfering with its function. To resolve this, ensure the station is installed in a dry location and protected from water exposure. If the problem persists, a qualified electrician should inspect it.
This answer is automatically generated