Savant SmartControl 3 Quick Reference Manual

Savant® SmartControl 3
Quick Reference Guide
Box Contents
(1) SmartControl 3 Controller (SSC-W003I-00)
(1) Installation Kit SmartControl 3 (075-0174-xx)
(1) Mounting Plate (074-0569-xx)
(1) 6-pin Screw Down Plug-in Connector (028-9352-xx)
(1) 5V DC 1.2A Power Supply (025-0165-xx)
(1) Cable Tie (014-0071-xx)
(1) Quick Reference Guide (this document)
Specifications
Environmental Environmental
Temperature 32° to 104° F (0° to 40° C)
Humidity 10% to 80% RH (non-condensing)
Dimensions and Weight Dimensions and Weight
Height 0.64 in (1.62 cm)
Width 2.70 in (6.85 cm)
Depth 2.67 in (6.78 cm)
Net: 0.25 lb (0.11 kg)
Weight Weight
Shipping: 1.50 lb (0.68 kg)
Power Power
Input Power 5V DC 1.2A
Max Power 6 watts
Standards Standards
Wireless Wi-Fi (802.11 b/g/n 2.4 GHz)
Security WPA1™, WPA2™, WPA1™ + WPA2™, WEP
Regulatory Regulatory
Safety and Emissions FCC Part 15 | CE Mark | C-Tick
Contains FCC ID: TLZ-CU277
Contains IC: 6100-CU277
RoHS Compliant
Minimum Supported Release Minimum Supported Release
Savant OS da Vinci 7.0
Network Requirements
Savant requires the use of a wireless network that is configured to
make use of at least one of the supported wireless Standards listed
in the Specifications Table.
Connect all Savant devices to the same local area network (LAN) or
subnet as the host. Savant recommends not implementing any type
of traffic or packet shaping in your network topology for the Savant
devices as this may interfere with performance.
Network Configuration
To ensure that the IP Address will not change due to a power outage,
a static IP Address or DHCP reservation should be configured.
Savant recommends using DHCP reservation within the router. By
using this method, static IP Addresses for all devices can be
managed from a single UI avoiding the need to access devices
individually.
Setting DHCP reservation varies from router to router. Refer to the
documentation for the router to configure DHCP reservation.
Connecting to a Wireless Network
Refer to the SmartControl 3 (SSC-W003I) Deployment Guide
located on the Savant Customer Community to connect the SSC-
W003I to the network.
SSC-W003I-00 | 009-1258-01 | 160217
Copyright © 2016 Savant Systems, LLC
Front Panel
Press and hold for 5 seconds while powered On to clear
A
network settings. Status LED will blink rapidly when reset is
complete.
Off: No Power
On Solid: Connected/Communicating with the Savant host.
Blinks Once: In Access Point Provisioning Mode and is ready to
be provisioned onto the local network.
Blinks Twice: Is connecting to the local network.
Blinks Three Times: Is connecting to the host.
B
Short Off Blink: Firmware is updating.
Rapid Blink: The reset button was held down for at least
five seconds and the SSC-W003I is performing a factory
reset.
Rear Panel
IR
Input Power 5V DC 1.2A - Connect to included power supply.
Cable Lance
1 of 2
Used to send IR signals to control devices with an
IR input or IR receiver via an IR flasher (5V
tolerant only).
6-pin Screw Down Plug-in Connector
See IR Wiring for important precautions regarding
IR functionality before making any connections.
Use with included cable tie to secure power
supply connection.
45 Perseverance Way, Hyannis, MA 02601
Savant.com
For Product Info
| 508.683.2500