Advertisement
PROGRAMMING THE NUMBER/CALL CODE
With monitor switched off, operate as it follows:
Press simultaneously and hold the
Wait for 3 seconds until the red led
push-buttons
and
within 5 seconds for at least 3 seconds until the red LED
lit. Now the device is on programming mode and can receive the number
to code from an entrance panel or from the programmer. At the code
reception and after a correct programming, the red led
and the device returns to the basic mode.
OPERATION
Monitors type 7214 must be used only on digital Digibus type ELVOX
video-interphone installations; for the supply voltage use only the digibus
range power supplies (for example type 6948).
The digibus system allows you to carry out installations with digital type
device and command identification. According to the installations configu-
ration, each device connected is identified by a 4 or 8 univocal numerical
code and it is able to receive and send a data packet containing all the
information related to the communication management; in fact each data
packet includes the identification of the destination device and the com-
mand to be carried out. All typical command operations of a video-inter-
phone system, such as call, electrical lock release, stair-light switching
on etc., are then codified.The audio and video signals are, on the contra-
ry, analogical type signals.
6
P R O G R A M M I N G - O P E R A T I O N - S E T T I N G S
and
push-buttons.
starts flashing. Release both
and press the
push-button
is steadily
switches off
SETTINGS
Ringtone volume and melody selection functions
These settings can be adjusted with the display switched off. Press
push-button
for 2 seconds, until the green LED
tom right flashes. This LED is normally used to indicate DOOR OPEN.
This flashing indicates "SETTING" mode, during which buttons
and
can be used to adjust the ringtone volume and push-buttons
and
to select the melody.
The monitor will remain in "SETTING" mode (green LED flashing) until
the arrow buttons are pressed. Wait for the flashing red LED
confirmation of changes made. SETTING mode is cancelled when the
arrow buttons are not pressed for more than 5 seconds. Nevertheless the
user can exit this mode by pressing button
LED switches off.
Ringtone mute function
Ringtone mute is activated using the same procedure described above
for adjusting the ringtone volume. Once the volume has been adjusted to
the lowest setting by repeatedly pressing the down arrow, the red LED
in the bottom left-hand corner illuminates to indicate that ringtone
mute is activated.
Melody programming of outdoor call
It is possible to choose the melody of outdoor call (call from landing). The
available melodies are the same as the ones for the call from speech
unit.
In order to choose the melody of outdoor call it is necessary to keep the
push-buttons pressed for 2 seconds
mode keep simultaneously pressed the push-buttons
until the red LED
At this point use the push-buttons
dy required. Once the melody has been chosen, wait until the monitor
exit the SETTING mode (switching off of green LED
Brightness and contrast control functions
These settings can be adjusted with the display switched on. Press push-
button
for 2 seconds, until the green LED
left flashes. This LED normally serves as the OPEN DOOR indicator. This
flashing indicates entry into "SETTING" mode, during which buttons
and
can be used to set the contrast and buttons
and
to select the brightness. When the maximum and minimum
values are reached, this is indicated by a beep. The monitor will remain
in "SETTING" mode (green LED flashing) until the arrow buttons are
pressed. SETTING mode is cancelled when the arrow buttons are not
pressed for more than 5 seconds. Nevertheless the user can exit this
mode by pressing button
Communication mode selection function (
It is possible to choose between two different modes of communication
with speech units or:
1. HANDS FREE mode: press the TALK/LISTEN push-button
the start of the conversation only, to activate the audio, and at the end
of the conversation to deactivate the audio. The "audio active" condi-
tion is indicated by the illumination of the red LED
left corner of the monitor, which is normally used to indicate RINGTO-
NE MUTE.
2. PUSH-TO-TALK mode: keep the talk/listen push-button
sed during the conversation; release it at the end of the conversation.
The 7200 series monitor is factory set to HANDS FREE communication
mode. To switch from one mode to the other, with the monitor switched
OFF press push-button
at the bot-
again until the green
to enter the SETTING
below starts flashing (about 2 seconds).
e
to select the melo-
).
at the bottom
again until the green LED switches off.
button)
at the bottom
for 2 seconds to enter SETTING mode;
for
and
at
pres-
Advertisement
