Advertisement
JEEP CHEROKEE ARB WINCH BULL BAR 1997 ON
WHEN INSTALLED IN ACCORDANCE WITH THESE INSTRUCTIONS, THE FRONT
PROTECTION BAR DOES NOT AFFECT OPERATION OF THE SRS AIRBAG.
TAKE NOTE OF THE FOLLOWING:
• THIS PRODUCT MUST BE INSTALLED EXACTLY AS PER THESE INSTRUCTIONS USING ONLY THE
HARDWARE SUPPLIED.
• DO NOT USE THIS PRODUCT FOR ANY VEHICLE MAKE OR MODEL, OTHER THAN THOSE SPECIFIED
BY ARB.
• DO NOT REMOVE LABELS FROM THIS BULL BAR.
• THIS PRODUCT OR ITS FIXING MUST NOT BE MODIFIED IN ANY WAY.
FITTING KIT No 6171262
USE
CONTROL BOX BRACKET
TO BULL BAR
WINCH TO BULL BAR
BULL BAR TO CHASSIS
No PLATE BRACKET,
NUMBER PLATE AND
INNER GUARD
20-5-98
If you have any queries regarding the installation of this product please contact the distributor from whom it was purchased, or alternatively the ARB office in your state.
Head Office – ARB corporation Ltd VIC: 42-44 Garden Street, Kilsyth, Victoria, 3137 Tel: (03) 9761 6622 Fax: (03) 9761 6807
WA:(08) 9244 3553 NSW: (02) 9821 3633 ACT: (02) 6280 7475 SA: (08) 8244 5001 QLD: (07) 3872 3872 NT: (08) 8947 2262 TAS: (03) 6331 4190
WARNING
FOR VEHICLES EQUIPPED WITH SRS AIRBAG
PART No
QTY
3751564
1
6151021
2
6151132
2
4581044
2
6151110
2
6151140
2
4581051
4
6151074
2
6821110
1
3193540
2
4581049
12
4581050
8
4581040
8
4581048
2
6151071
2
6151100
8
6151138
4
5846267
2
3751485
1
6151017
8
6151046
8
6151128
8
3500080
1
Page 1 of 4
DESCRIPTION
BRACKET CONTROL BOX
BOLT M8 X 1.25 X 20mm
NUT FLANGE M8 X 1.25
WASHER FLAT M8 X 17 X 1.2
BOLT UNC 5/8 X 6" GRADE 8
NUT UNC 5/8 NYLOC
WASHER FLAT 5/8"
BOLT UNC 3/8 X 1 ¾" GR5
RUBBER GROMMET
PLATE - CAPTIVE NUT ASSY
WASHER FLAT 1/2" X 1 1/8" X 12G
WASHER SPRING 1/2" X 1/8" X 1/8"
WASHER FLAT M10
WASHER SPRING M10
BOLT UNC 3/8 X 1"
BOLT UNC 1/2X11/2" CLASS 8
NUT UNC ½"
PACKER
BRKT NUMBER PLATE
BOLT M6 X 1.0 X 16mm
WASHER FLAT 6mmZP
NUT FLANGE M6 X 1.0
ARB INDICATOR KIT
No 3450080
3782549
Advertisement
Table of Contents
Related Manuals for ARB 3450080
Summary of Contents for ARB 3450080
- Page 1 3782549 If you have any queries regarding the installation of this product please contact the distributor from whom it was purchased, or alternatively the ARB office in your state. Head Office – ARB corporation Ltd VIC: 42-44 Garden Street, Kilsyth, Victoria, 3137 Tel: (03) 9761 6622 Fax: (03) 9761 6807...
- Page 2 TOOLS REQUIRED Basic tool kit, drill and ½” drill bit PROCEDURE Place the bull bar onto a suitable stand. New mounting holes must be drilled in the roller fairlead in order to line up with the winch mounting holes in the bull bar. (Refer to diagram 1.) DIAGRAM 1 Remove the circlips which retain the side pins.
- Page 3 Place the bull bar on top of the winch and align with the mounting holes. Using the bolts supplied with the winch and the 3/8” washers in the ARB kit, fit and tighten the two upper bolts. Place the roller fairlead in position over the two lower holes and fit two 3/8” x 1 ¾” bolts and 3/8”...
- Page 4 DIAGRAM 4 Align the bull bar and tighten the two 3/8” bolts. Using the bull bar as a template. Drill out the lower forward holes in the chassis to ½”. (Refer to diagram 4.) Insert the 2 captive nut plates into the inside of the chassis rail with the tab towards the front. Fit the four 1/2”...
Need help?
Do you have a question about the 3450080 and is the answer not in the manual?
Questions and answers