Ingersoll-Rand Liftstar LS2-600H Product Information
Ingersoll-Rand Liftstar LS2-600H Product Information

Ingersoll-Rand Liftstar LS2-600H Product Information

Portable air winch
Hide thumbs Also See for Liftstar LS2-600H:

Advertisement

Product Information
Liftstar Hydraulic Winch
Model LS2-600H and PS2–1000H
(Dwg. MHP2827)
Save These Instructions
Form MHD56359
Edition 2
February 2014
43801711
R
2014 Ingersoll Rand
©

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Liftstar LS2-600H and is the answer not in the manual?

Questions and answers

Summary of Contents for Ingersoll-Rand Liftstar LS2-600H

  • Page 1 Product Information Liftstar Hydraulic Winch Model LS2-600H and PS2–1000H (Dwg. MHP2827) Save These Instructions Form MHD56359 Edition 2 February 2014 43801711 2014 Ingersoll Rand ©...
  • Page 2: Specifications

    Only allow trained technicians to perform maintenance on this product. For additional information contact factory or nearest Ingersoll Rand Ingersoll Rand Distributor. For additional supporting documentation refer to Table 1 ‘Product Information Manuals’ on page 2. Manuals can be downloaded from http://www.ingersollrandproducts.com. The use of other than genuine Ingersoll Rand replacement parts may result in safety hazards, decreased performance and increased maintenance and will invalidate all warranties.
  • Page 3: Hydraulic System

    Wire Rope Selection n Hydraulic System Consult a reputable wire rope manufacturer or distributor for assistance in selecting Refer to Dwg. MHP2853 on page 7. the appropriate type and size of wire rope and, where necessary, a protective coating. Use a wire rope which provides an adequate safety factor to handle the actual working load and meets all applicable industry, trade association, federal, Hydraulic Hoses state and local regulations.
  • Page 4: Operation

    1. Make sure the hydraulic motor and case drain line is filled with the recommended Control Valve hydraulic fluid. Internal motor leakage at low operating pressures may not be sufficient to provide start-up lubrication. Ensure control valve moves smoothly in the haul-in and payout directions before 2.
  • Page 5: Frequent Inspection

    INSPECTION Inspection information is based in part on American Society of Mechanical Engineers 6. Winch Operation: Power winch in both directions. Winch must operate Safety Codes (ASME B30.17). smoothly without sticking, binding or abnormal noises and have minimal vibration. 7. Hydraulic System: Check hydraulic lines, fittings, valves and other components WARNING for deterioration, leakage or wear.
  • Page 6: Recommended Lubricants

    Disc Brake n Recommended Lubricants Refer to the manufacturer’s literature for lubrication requirements. Table 7: Reduction Gear Recommended Lubricants Wire Rope Temperature Type Oil * - Synthetic oil rinematic viscosity 68 Cst Follow the wire rope manufacturer's instructions. At a minimum, observe the following guidelines.
  • Page 7 PRODUCT INFORMATION GRAPHICS Wire Rope Wedge Wire Rope (Dwg. MHP0138) (Dwg. MHP2636) Remote Control Station Unload Hoses O 1/4 Counter Balance Valve LsB: 80b LP1: Safety Main Relief Valve LSA: Reducing Valve for Haul-in (winding) LSB: Reducing valve for Payout (unwinding) LsA: 120b WINCH: Payout Port 1/2”...
  • Page 8 PRODUCT INFORMATION GRAPHICS CONTINUED Haul-In Payout Motor End (Dwg. MHP2857) Pull Plunger Out for Free Spooling Rotate Lever Clockwise to Release Plunger (Dwg. MHP2626) For reference only, motor/controls may be different for your model. (Dwg. MHP3415) Form MHD56359 Edition 2...
  • Page 9 SERVICE NOTES Form MHD56359 Edition 2...
  • Page 10 SERVICE NOTES Form MHD56359 Edition 2...
  • Page 11 SERVICE NOTES Form MHD56359 Edition 2...
  • Page 12 www.ingersollrandproducts.com...

This manual is also suitable for:

Pullstar ps2-1000h

Table of Contents