Dual Motor Proportioning Drive Input / Output List - GE IC3645SR4R404U2 Installation And Operation Manual

OUTLINE DRAWINGS, ELEMENTARY DRAWINGS AND INPUTS/OUTPUTS
SX TRANSISTOR CONTROL
Section 3.6 Standard Dual Motor Proportioning Drive and Pump Control Input/Output List
STANDARD DUAL MOTOR PROPORTIONING
PIN MAIN PLUG INPUT/OUTPUT DESCRIPTION
1 BATTERY VOLTS FROM BATTERY
2 BATTERY VOLTS FROM KEY
3 BATTERY VOLTS FROM START SWITCH
4 BATTERY VOLTS FROM FORWARD SWITCH
5 BATTERY VOLTS FROM REVERSE SWITCH
6 BATTERY VOLTS FROM SEAT SWITCH
7 ACCELERATOR INPUT VOLTAGE SIGNAL
8 ACCELERATOR NEGATIVE
9 ACCELERATOR POT +5 VOLTS SUPPLY
10 BDI INTERRUPT
11 PLUG/REGEN OUTPUT SIGNAL +12V
12 STEER ANGLE POT WIPER
13 SPEED LIMIT SWITCH INPUT
14 TACHOMETER INPUT SIGNAL
15 TACHOMETER +12 VOLTS SUPPLY
16 MOTOR CURRENT COMPENSATION
17 LINE CONTACTOR DRIVER AND SUPPRESSION
18 1A OR STEER PUMP CONTACTOR DRIVER AND SUPPRESSION
19 STEER ANGLE POTENTIOMETER +5V SUPPLY
20 STEER ANGLE POTENTIOMETER NEGATIVE
21 PMT SIGNAL FROM SLAVE
22 SERIAL RECEIVE
23 SERIAL TRANSMIT
MOTOR TRACTION "Y" PLUG
PIN INPUT/OUTPUT DESCRIPTION
1 CLOCK (OUT) ( DASH DISPLAY-4)
2 DATA (OUT) ( DASH DISPLAY-3)
3 ENABLE (OUT) ( DASH DISPLAY-1)
4 NEGATIVE ( DASH DISPLAY-2)
5 +5V SUPPLY ( DASH DISPLAY-5)
6 CONT/STORE (IN) (HANDSET)
7 MOTOR CURRENT
8 VALUE (TMMA-9)
9 FUNCTION (TMMA-7)
10 +5V SUPPLY (TMMA-13)
11 SERIAL RECEIVE
12 SERIAL TRANSMIT
Connections to Main Plug (23 Pin) and "Y" Plug (12 Pin)
1 2 3 4 5 6
7 8 9 10 11 12
WIRE END VIEW "Y" PLUG
STANDARD PUMP
MAIN PLUG INPUT/OUTPUT DESCRIPTION
BATTERY VOLTS FROM BATTERY
BATTERY VOLTS FROM KEY
BRUSH WEAR (TMM) FAULT 93
BRUSH WEAR (TMM) FAULT 93
BRUSH WEAR (TMM) FAULT 94
BRUSH WEAR (TMM)FAULT 94
ACCELERATOR INPUT VOLTAGE SIGNAL
BRUSH WEAR (TMM) FAULT 95
BRUSH WEAR (TMM) FAULT 95
PUMP ENABLE (BDI INTERRUPT)
OVERTEMP (TMM) FAULT 91
SPEED LIMIT 1
TRUCK MANAGEMENT BRUSH WEAR OUTPUT
TRUCK MANAGEMENT OVERTEMP OUTPUT
OVERTEMP (TMM) FAULT 90
OVERTEMP (TMM) FAULT 92
LINE CONTACTOR DRIVER (PMT)
1A CONTACTOR DRIVER
SPEED LIMIT 2
SPEED LIMIT 3
SPEED LIMIT 4
RS232 RECEIVE
RS232 TRANSMIT
MOTOR PROPORTIONING "Y" PLUG
INPUT/OUTPUT DESCRIPTION
CLOCK (OUT) ( DASH DISPLAY-4)
DATA (OUT) ( DASH DISPLAY-3)
ENABLE (OUT) ( DASH DISPLAY-1)
NEGATIVE ( DASH DISPLAY-2)
+5V SUPPLY ( DASH DISPLAY-5)
CONT/STORE (IN) (HANDSET)
MOTOR CURRENT
VALUE (TMMA-9)
FUNCTION (TMMA-7)
+5V SUPPLY (TMMA-13)
SERIAL RECEIVE
SERIAL TRANSMIT
1 2 3 4 5 6 6 8
9 10 11 12 13 14 15
16 17 18 19 20 21 22 23
WIRE END VIEW - MAIN PLUG
Page 16
October 1998