Standard Pump Elementary; Standard Dual Motor Proportioning Drive Input / Output List - GE IC3645SR4U454Z2 Installation And Operation Manual

OUTLINE DRAWINGS, ELEMENTARY DRAWINGS AND INPUTS/OUTPUTS
SX TRANSISTOR CONTROL
Section 3.6 Dual Motor Proportioning Drive and Pump Control Input and Output List
MOTOR PROPORTIONING
PIN INPUT/OUTPUT DESCRIPTION
1 BATTERY VOLTS FROM BATTERY
2 BATTERY VOLTS FROM KEY
3 BATTERY VOLTS FROM START SWITCH
4 BATTERY VOLTS FROM FORWARD SWITCH
5 BATTERY VOLTS FROM REVERSE SWITCH
6 BATTERY VOLTS FROM SEAT SWITCH
7 ACCELERATOR INPUT VOLTAGE SIGNAL
8 ACCELERATOR NEGATIVE
9 ACCELERATOR POT +5 VOLTS SUPPLY & STEER POT
10 BDI INTERRUPT (LEFT) AND PMT ENABLE INPUT (RIGHT)
11 PLUG/RGN OUTPUT SIGNAL +12V
12 STEER ANGLE INPUT VOLTAGE SIGNAL
13 NOT USED
14 N.O. BRAKE SW.
15 I OUT
MOTOR
16 MOTOR CURRENT COMPENSATION
17 LINE CONTACTOR DRIVER AND SUPPRESSION
18 1A OR STEER PUMP CTR DRIVER AND SUPPRESSION
19 STEER ANGLE POT +5 VOLTS SUPPLY
20 NOT USED
21 PMT ENABLE OUTPUT
22 +12V TACH
23 TACH INPUT
MOTOR PROPORTIONING "Y" PLUG
PIN INPUT/OUTPUT DESCRIPTION
1 CLOCK (OUT) ( DASH DISPLAY-4)
2 DATA (OUT) ( DASH DISPLAY-3)
3 ENABLE (OUT) ( DASH DISPLAY-1)
4 NEGATIVE ( DASH DISPLAY-2)
5 +5V SUPPLY ( DASH DISPLAY-5)
6 CONT/STORE (IN) (HANDSET)
7 TACH INPUT
8 VALUE
9 FUNCTION
10 +12V TACH OUT
11 SERIAL RECEIVE
12 SERIAL TRANSMIT
1
7
WIRE END VIEW "Y" PLUG
CONNECTIONS TO MAIN PLUG (23 PIN) AND "Y" PLUG (12 PIN)
STANDARD DUAL
1=PLUG
2 3 4 5 6
8 9 10 11 12
INPUT/OUTPUT DESCRIPTION
BATTERY VOLTS FROM BATTERY
BATTERY VOLTS FROM KEY
STATUS CODE 93 INPUT
STATUS CODE 93 INPUT
STATUS CODE 94 INPUT
STATUS CODE 94 INPUT
POTENTIOMETER INPUT VOLTAGE SIGNAL
STATUS CODE 95 INPUT
STATUS CODE 95 INPUT
PUMP ENABLE SIGNAL 12VDC
STATUS CODE 91 INPUT
SPEED LIMIT #1 INPUT
TMM1 BRUSHWEAR INDICATER OUTPUT
TMM1 OVER TEMPERATURE OUTPUT
STATUS CODE 92 INPUT
STATUS CODE 90 INPUT
LINE CONTACTOR DRIVER
1A CONTACTOR DRIVER
SPEED LIMIT #2 INPUT
SPEED LIMIT #3 INPUT
SPEED LIMIT #4 INPUT
+12V TACH
TACH INPUT
INPUT/OUTPUT DESCRIPTION
CLOCK (OUT) ( DASH DISPLAY-4)
DATA (OUT) ( DASH DISPLAY-3)
ENABLE (OUT) ( DASH DISPLAY-1)
NEGATIVE ( DASH DISPLAY-2)
+5V SUPPLY ( DASH DISPLAY-5)
CONT/STORE (IN) (HANDSET)
TACH INPUT
VALUE
FUNCTION
+12 TACH OUT
SERIAL RECEIVE
SERIAL TRANSMIT
1 2 3 4 5 6 6 8
9 10 11 12 13 14 15
16 17 18 19 20 21 22 23
WIRE END VIEW - MAIN PLUG
STANDARD
PUMP
PUMP "Y" PLUG
NOTE:
•=
PY7 is connected
internally to P23
•=
PY10 is connected
internally to P22
January 1999
Page 18