Related Manuals for Eaton Ferrups FX
Summary of Contents for Eaton Ferrups FX
- Page 1 Eaton Ferrups FX UPS Ferrups FX UPS Eaton Ferrups FX User’s Guide p/n: P-164000906 Revision 05...
- Page 2 Some configurations are classified under IEC 62040-2 as “C2 UPS for Unrestricted Sales Distribution.” ©Copyright 2021 Eaton, Raleigh, NC, USA. All rights reserved. No part of this document may be reproduced in any way without the express written approval of Eaton.
- Page 3 (WEEE) in the trash. For proper disposal, contact your local recycling/ reuse or hazardous waste center. IMPORTANT To ensure you have the most up-to-date content and information for this product, please review the latest manual revision on our website, www.eaton.com/ferrupsfx.
- Page 4 5.10 Third Party Intellectual Property Rights. The Firmware may contain components transfer the Firmware directly to a third party only in connection with the sale of the Eaton (including open source software components) that are owned by third parties (“Third Party product in which it is installed.
-
Page 5: Table Of Contents
8 8 U U P P S S S S t t a a r r t t u u p p ..........................................................4 4 7 7 Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05... - Page 6 1 1 3 3 W W a a r r r r a a n n t t y y ............................................................7 7 9 9 13.1 Two-Year Limited Warranty (US and Canada) ....................79 Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05...
- Page 7 Normally Open REPO Connection....................30 Figure 16. Normally Closed REPO Connections ....................30 Figure 17. Remote Control Display......................... 33 Figure 18. BPE Terminal Block ........................48 Figure 19. UPS Overall Dimensions........................ 75 Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05...
- Page 8 List of Figures viii Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05...
- Page 9 Table 36. Bypass Switch Dimensions and Weight ..................... 76 Table 37. Battery Cabinet Dimensions ......................76 Table 38. Battery Cabinet Weight........................76 Table 39. UPS Runtimes ..........................76 Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05...
- Page 10 List of Tables Table 40. Battery Specification ........................77 Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05...
- Page 11 SERVICE PERSONNEL ONLY. There are NO USER SERVICEABLE PARTS inside the UPS. • When using a customer supplied non Eaton battery configuration with the FX UPS the ABM charger will be disabled. The calculated UPS runtime will not be accurate and the period of time for the batteries to fully charge could be affected.
-
Page 12: Receiving And Unpacking The Ups
The Eaton Ferrups FX 3100 UPS has a castor kit making it easy to move the UPS to the installation site once it is unpacked. If the receiving area is far from the site, Eaton recommends that you move the UPS with a pallet jack before the UPS is unpacked. - Page 13 Receiving and Unpacking The UPS Retract the leveling feet by turning them counter clockwise then carefully roll the cabinet down to its intended operating location. Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05...
- Page 14 Receiving and Unpacking The UPS Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05...
- Page 15 F F X X R R e e m m o o t t e e C C o o n n t t r r o o l l D D i i s s p p l l a a y y ( ( R R C C D D ) ) The Remote Control Display (RCD) is included with all Eaton Ferrups FX UPS models providing hand held operation enabling the end user to communicate and interpret UPS operating modes, alarms and events.
-
Page 16: Bypass Switches
O O u u t t p p u u t t R R e e c c e e p p t t a a c c l l e e s s Different user replaceable receptacle panel options are available for the Eaton Ferrups FX UPS. Consult your dealer or Eaton for compatibility with your UPS. -
Page 17: Communication Overview
C C o o m m m m u u n n i i c c a a t t i i o o n n O O v v e e r r v v i i e e w w Eaton offers several methods of communicating with your Eaton Ferrups FX UPS system in addition to the remote control display. - Page 18 Communication Overview Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05...
- Page 19 A A n n c c h h o o r r B B r r a a c c k k e e t t I I n n s s t t a a l l l l a a t t i i o o n n The Eaton Ferrups FX series UPS cabinet is shipped with four anchor brackets that secure the UPS to the pallet. These brackets should be reused to attach the UPS to the floor, they act as a protective stop to prevent the cabinet from rolling forward if unintentionally pushed.
-
Page 20: Anchor Bracket Installation
Using the proper type of customer-supplied screws for the intended mounting surface, attach each bracket to the floor. All screws must be properly driven into the structural material. Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05... -
Page 21: Initial Startup For Units Installed With A Bpe Bypass Switch
Continue to section 8.1 “Startup For Hardwired Units” in the Eaton Ferrups FX series UPS users guide for units that do not have an external bypass switch. • “ ” and “” describe the recommended breaker and wire size for installation of the Eaton Ferrups FX series UPS. •... -
Page 22: Ups Terminal Connections
Insert the L1, L2 N and G cable ends thru the wiring access cover into the applicable terminal slots in the terminal block. Secure the cables by screwing down the lug screws. Reinstall the wiring access cover and ensure strain relief connections are secure. Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05... -
Page 23: Bpe Bypass Switch Operation
BPE Bypass Switch Operation To reduce the possibility of electric shock all AC and DC terminal covers must be installed on the back of the UPS prior to applying power to the Eaton Ferrups FX series UPS. 4 4 . . 4 4... - Page 24 U.S. see the following table to size the wire. Mount the bypass switch within sight of the UPS. If you do not have a Eaton bypass switch with a AC disconnect switch or the fuse box or panel is out of sight, you must install a separate disconnect switch next to the UPS.
-
Page 25: Bpe Bypass System Wiring Diagrams
B B P P E E B B y y p p a a s s s s S S y y s s t t e e m m W W i i r r i i n n g g D D i i a a g g r r a a m m s s The following notes are referenced by their number in the UPS external bypass wiring diagrams. Refer to the correct wiring diagram for correct installation. Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05... - Page 26 This grounding electrode conductor must be at least #8 AWG (8.36 mm). If the UPS input circuit conductors are larger than #8 AWG (8.36 mm), Eaton requires the grounding electrode conductor to be the same size ( ampacity ) as the largest UPS input circuit conductor.
- Page 27 FX 3100 120V In - 120V Out Using a BPE Bypass Switch Table 9. Wire Size Recommendations Model Input Voltage Input Breaker Size 75°C Copper Wire Size FX3100 120 Vac 8 AWG (8.4 mm²) Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05...
- Page 28 BPE Bypass System Wiring Diagrams Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05...
- Page 29 NFPA 70-2020. • If you are replacing batteries or repairing battery connections, follow the procedure in the Eaton FERRUPS FX User's Guide to shut off your UPS and remove both AC and DC input power. Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05...
-
Page 30: Preparation For Battery Installation
FX 3.1 kVA models have a removable plug at the UPS; the external battery cabinets have a DC breaker. Figure 10. Eaton FX3100 UPS wiring to EBM TO UPS/EBM FROM EBM To UPS/EBM FROM EBM Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05... -
Page 31: Battery Cabinet Installation
Use the battery installation diagram that came with the UPS batteries and cabinet as you follow the steps below. Place the external battery cabinet or rack as close as possible to the Eaton Ferrups FX UPS. If the batteries will be further from the unit than the standard cables allow, contact your service representative or your local distributor for assistance. - Page 32 Battery Cabinet Installation Never install the batteries in a air tight enclosure. The Eaton Ferrups FX external battery cabinets come with a battery installation diagram. Refer to this diagram for proper battery and cable connections. Find the battery cable assembly that connects to the UPS. (If you have a removable DC plug at the UPS end, note that this end of the cables does not go through the conduit or connect to it.)
- Page 33 Battery Cabinet Installation Model Nominal Battery Voltage FX3100 48Vdc After you have checked the DC voltage, turn the DC switch on the external battery cabinet(s) to the OFF position. Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05...
-
Page 34: Fxebm01 Figure
BAA-0212 108” BAA-0207 24” BAA-0203 108” BAA-0208 32” BAA-0204 108” P-175000115 45” P-175000116 35” P-175000117 38” P-175000118 31” P-175000119 17” Termina�on & Labeling Descriptors + 15 - 16 Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05... -
Page 35: Fxebm03 - Fxebm06 Wiring Diagram
BAA-0207 24” BAA-0212 108” BAA-0208 32” BAA-0203 108” P-175000115 45” BAA-0204 108” P-175000116 35” P-175000117 38” P-175000118 31” P-175000119 17” Termina�on & Labeling Descriptors + 15 - 16 Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05... - Page 36 FXEBM03 — FXEBM06 Wiring Diagram Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05...
- Page 37 C C o o m m m m u u n n i i c c a a t t i i o o n n s s Eaton offers several methods of communicating with your Eaton Ferrups FX UPS system in addition to the front Remote Control Display.
-
Page 38: Communications
UPS is on the bypass or not. Load on battery The load is protected. The UPS supplies the load from the battery (not using utility power). Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05... -
Page 39: Input And Output Signal Connections
REPO Connections For the Eaton Ferrups FX UPS, REPO can be configured either as Normally Open (NO) or Normally Closed (NC) contacts. The REPO connector on the rear panel of the UPS is used for powering off the UPS in a emergency situation Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05... - Page 40 For Future use. On Generator Input Signal The generator contact provides a normally open contact to display a notice to indicate the UPS is being supplied from a generator. Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05...
- Page 41 The alarm contact is a optocoupler circuit that provides a 5VDC 1 mA signal that can be used to provide notification that the UPS is on alarm. For a general purpose relay contact the Relay Card-MS can be ordered. Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05...
- Page 42 Input and Output Signal Connections Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05...
- Page 43 Level: This is the level of the password programed into the UPS. ( Only visible if a password is entered ). NOTE The display will time out and go blank after 3 minutes of inactivity, press any button to resume normal activity, Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05...
-
Page 44: Front Panel Indicators
UPS • Blue : UPS is operating without alarms or warnings • Yellow: UPS is operating on battery power. • Red: The UPS is indicating an alarm condition. Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05... -
Page 45: Changing Operating Modes
The names of the Eaton FERRUPS FX control features are located in yellow at the bottom of the Remote Control Display keys. You can change the operating mode by pressing the [CONTROL] button followed by the number that describes the operating mode. -
Page 46: Enter A User Password
[DISPLAY], the parameter number, and [ENTER]. For example, to display parameter 0 (Time), follow these steps: Table 17. Display a Parameter Press this Key Display Shows [DISPLAY] Display: Display: 0 [ENTER] 00 Time : 09:30:00 Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05... -
Page 47: Ups Parameters
When the unit is on battery, this is the discharge current. Otherwise, this is the “06 I Batt 0.0 A” Service 0.0 – 200.0 charging current. Programming changes an internal setting to calibrate reading. Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05... - Page 48 It will scroll all Active alarms, each for 3 seconds. User can toggle scrolling by 20 ActiveAlm "Batt No Change pressing '0'. When scrolling is stopped, Disconnected" Allowed pressing '1' will move to next event (older). Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05...
- Page 49 Minimum number of seconds the UPS will 58 XferDly 5 s run on inverter before transferring back to Service 1 – 600 AC line operation. Actual time on inverter Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05...
- Page 50 When using custom batteries, the time of 73 Test@ 1:00:00 User 0 - 23:59:00 day that the battery discharge test will start. Reserved Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05...
- Page 51 UPS. 0)Disabled 92 ABM 1)Enabled User ABM enable. 1)Enabled 3,4,5,6 Months ABM Discharge Test Interval. 93 AbmIntrvl 3 mo User 0)Disabled 94 Chrgr 1)Enabled Charger enable. User 1)Enabled Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05...
- Page 52 1) Enabled Generator mechanism. 110 ChrgrI 20 A Charger Current rating. User 0 - 20 0)Disabled Allows enabling and disabling of 111 CROO 0)Disabled User Communication Remote On/Off. 1)Enabled Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05...
- Page 53 UPS will switch to the buck tap. (NOTE: “131 BucKV 105.58 No Change 60.00 – 276.00 parameter 133 is applied to this set point to %” Allowed provide hysteresis) Reserved Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05...
-
Page 54: Using The Remote Control Display Configuration Menu
You may need to lock the control panel if you want to limit its use. When disabled the keypad does not respond to the key functions until it is enabled again. Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05... -
Page 55: Locking And Unlocking The Remote Control Panel
— Keypad Locked — Unlocking the Keypad Press This Key Display will Show [CLEAR] and [ENTER] together Unlock # [0] [8] [2] [0] [4] [9] Unlock #: 082049 [ENTER} Keypad Unlocked Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05... - Page 56 Locking and Unlocking the Remote Control Panel Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05...
- Page 57 The voltages in the Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05...
- Page 58 12. Turn the bypass switch to the LINE position. Measure the voltage to the protected equipment and verify it is correct. 13. Turn the bypass switch to the UPS position and verify the voltage to the protected equipment is still correct. Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05...
-
Page 59: Initial Startup Parameters
Display Shows [DISPLAY] Display: Display: 0 [ENTER] 00 Time: 11:30:20 [PROGRAM] 00 Pgm: Enter the correct time (in 24-hour format). For example, if the time is 9:30 a.m.: Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05... - Page 60 [ENTER] 10 Date 01/01/19 To ensure maximum battery runtime, the Eaton FX Ferrups UPS can be programmed for up to four FX battery runtime options. To set the battery cabinet options you can program each cabinet type into parameters 95–98.
- Page 61 95 EBM 1 : 1) FXEBM01 *0 is the default setting for parameters 95–98* Repeat the steps above for parameters 96 through 98 if more than one Eaton FX Ferrups battery cabinet is to be used. Setup for Using a Custom Non Eaton Ferrups FX Battery Configuration...
-
Page 62: Automatic Battery Test
A A u u t t o o m m a a t t i i c c B B a a t t t t e e r r y y T T e e s s t t The Eaton FX Ferrups UPS has a built in automatic battery discharge test feature. When ABM is enabled (by default) the battery discharge test will run automatically every 90 days. - Page 63 FX3100 Turn the DC breaker on the back of the UPS to the OFF position. If you have an external battery cabinet with a DC switch or a Eaton Ferrups FX battery cabinet with a breaker, turn to the OFF position. If...
-
Page 64: Ups Shutdown
7.8 UPS Shutdown In order to replace the receptacle panel (if equipped) in the back of the Eaton Ferrups FX series follow the procedure described below. Turn the receptacle panel main breaker to the off position. -
Page 65: Receptacle Panel Replacement
Insert the new receptacle panel assembly into the back of the unit. Ensure that the panel fits tight to the back panel of the UPS and that the screw holes are in line. Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05... - Page 66 Turn the receptacle panel main breaker to the ON position. If the UPS was placed in standby mode prior to replacing the receptacle panel see chapter 8 to turn the UPS back to the auto mode. Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05...
-
Page 67: Storage And Operating Environment
Eaton, Powerware, and BladeUPS are registered trademarks of Eaton Corporation or its subsidiaries and affiliates. Phillips and Pozidriv are registered trademarks of Phillips Screw Company. Copyright 2008–2010 Eaton Corporation, Raleigh, NC, USA. All rights reserved. No part of this document may be reproduced in any way without the express written approval of Eaton Corporation. -
Page 68: Updating The Ups Firmware
To keep the UPS firmware updated with the latest improvements and benefits, visit www.eaton.com/ferrupsfx often for updates. You can download the latest firmware version. The downloadable file includes the instructions for installing the update. Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05... - Page 69 1 1 0 0 . . 1 1 A A c c c c e e s s s s i i n n g g t t h h e e U U P P S S L L o o g g The Eaton Ferrups FX UPS stores alarms, events and status information in the UPS log.
-
Page 70: Displaying Active Alarm Conditions
[2] [0] Display: 20 [ENTER] 20 Log The display automatically scrolls through the log entries. You can use the number keys as you view this scrolling display to : Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05... -
Page 71: Silencing The Alarm
1 1 0 0 . . 4 4 D D e e t t e e c c t t i i n n g g a a n n A A l l a a r r m m C C o o n n d d i i t t i i o o n n When the Eaton FERRUPS FX UPS detects an alarm condition, the UPS displays the alarm. The ALARM indicator on the remote control display illuminates and sounds an audible alarm. -
Page 72: Troubleshooting The Ups At The System Level
UPS’ rear panel. If this is a Battery when input AC is UPS without internal turned off. batteries, make sure that an EBM is connected to the UPS Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05... - Page 73 Check connector for loose panel malfunctioning. connection and pull the cable out and reconnect properly. If that doesn’t fix it, replace front panel and check if the new panel works. Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05...
-
Page 74: Alarm Conditions
(CB) if it is Off. If it is Off, check AC Input Source and make sure it is compatible with the UPS’ ratings. If input AC Source measures good, turn the Input CB ON. Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05... - Page 75 (closing) on AC Board CLOSED Battery Voltage BATTERY DC Charge Mode supporting Power Cycle. If problem OVER VOLTAGE exceeding max limit Load persists, turn unit off and call Eaton Service. Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05...
- Page 76 AC Input is condition. REMOTE Check why REPO was EMERGENCY activated at your site Check POWER OFF REPO Wiring at signal input on back of UPS. Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05...
- Page 77 UPS got activated by mistake. AMBIENT Ambient exceeds max Make sure UPS is in an OVERTEMPERA- temperature of 70C ambient temperature <= TURE 40C. Check Fans. Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05...
- Page 78 Hardware failure Call Eaton Service OVERCURRENT exceeded OUTPUT Output current exceeds Depends on amount of Reduce load and check if OVERCURRENT max rating - overload overload alarm clears. Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05...
- Page 79 Wait for Discharge test to TEST ABORTED changes by more than time to run discharge test run again when possible 10% during the again. discharge test, the test is aborted Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05...
- Page 80 Call Eaton Service OVERTEMPERA- reporting over TURE temperature and UPS turned off XFMR Ferro Transformer Call Eaton Service OVERTEMPERA- reporting over TURE TRIP temperature and UPS turned off Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05...
- Page 81 1 1 1 1 . . 1 1 S S e e r r v v i i c c e e a a n n d d S S u u p p p p o o r r t t If you have any questions or problems with the UPS, call your Local Distributor or the Eaton Help Desk at one of the following phone numbers and ask for a technical support representative.
-
Page 82: Service And Support
Service and Support Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05... - Page 83 The ferroresonant transformer inherently limits current and provides overload protection. The Eaton Ferrups FX UPS has high AC and low AC output voltage alarms, as well as an overload alarm. If the AC output voltage falls below the low AC output voltage alarm setpoint, the UPS sounds an alarm after 5 seconds.
-
Page 84: Environmental And Safety
The air around the UPS must be clean and free of dust, corrosive chemicals, and other contaminants. The Eaton Ferrups FX UPS uses internal fans to circulate the air for cooling. The air must be free to circulate around the UPS and external battery cabinet(s). Do not operate the UPS in a sealed room or container. -
Page 85: Ups Weights And Dimensions
Table 35. Available Break Before Make Bypass Switch Models Model Number Ratings (UL/CSA) Continuous Ratings (TÜV) Continuous BPEFXBBM02 40A/300 Vac 50A/300 Vac BPEFXBBM04 80A/300 Vac 80A/300 Vac BPEFXBBM05 104A/300 Vac 120A/300 Vac Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05... -
Page 86: Battery Cabinet Weights And Dimensions
Ah Rating / DC Voltage Full Load Half Load **Standard Internal Batteries Only** 33Ah/1 String/48V 14 Minutes 35 Minutes **FXEBM01 w/o UPS Internal 70Ah/2 Strings/48V 86 Minutes 242 Minutes Batteries** Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05... -
Page 87: Battery
UPS12–150MR (12 Volt) • PWHR12280W4FR (12 Volt) • PWHR12330W4FR (12 Volt) • PWHR12620W4FR (12 Volt) • SWU585–12FR (12 Volt) Recharge Time Charge to 80% usable capacity within 3 hours. Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05... - Page 88 Battery Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05...
- Page 89 For warranty information, please refer to the Resources link on our website, Two-Year Limited Warranty Eaton Load Protection Guarantee. For product registration please visit the UPS product registration page, Eaton UPS Product Registration. Eaton Ferrups FX UPS P-164000906 Eaton Ferrups FX User’s Guide P-164000906—Rev 05...
- Page 90 P-16400090605 P-164000906 05...