Eaton Powerware 3105 UPS User Manual
Eaton electrical corporation 3105 ups powerware users manual
Hide thumbs
Also See for Powerware 3105 UPS:
- User manual (12 pages) ,
- Reference manual (120 pages) ,
- User manual (2 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Eaton Powerware 3105 UPS
Summary of Contents for Eaton Powerware 3105 UPS
- Page 1 Powerware 3105 UPS UserÊs manual UserÊs Manual 350-700VA Rev B...
- Page 2 ©2006 Eaton Corporation All Rights Reserved The contents of this manual are the copyright of the publisher and may not be reproduced (even extracts) unless permission granted. Every care has been taken to ensure the accuracy of the information contained in this manual, but no liability can be accepted for any errors or omission.
-
Page 3: Table Of Contents
Powerware 3105 UPS UserÊs manual 1023921 Revision B Contents Introduction ... 4 Features ... 4 Unit inspection ... 4 Safety Instructions ... 5 Battery connection required before use! ... 6 Connecting the Battery: ... 6 Installation and Operation: ... 6 Typical applications ... -
Page 4: Introduction
Compact design fits on/under your desk; can also be mounted to a wall Unit inspection Once you have received the Powerware 3105 UPS product, you should remove and inspect the product for shipping damage. If any damage is found, please notify the carrier and your dealer. -
Page 5: Safety Instructions
Although the unit may be unplugged from utility power, hazardous voltage still may be present through the battery. Place the Powerware 3105 UPS indoors in an area that has adequate airflow and is free of excessive dust. Do NOT allow the UPS to be exposed to moisture, rain, excessive heat, or direct sunlight. -
Page 6: Battery Connection Required Before Use
Principle shown below. For detailed information how to connect, please refer to battery replacement section. Installation and Operation: The following steps explain how to connect and operate the Powerware 3105 UPS. Connect the UPS to a grounded power outlet. Note It is recommended that the battery should be charged for minimum 8 hours to ensure full charge before placing the UPS in service. -
Page 7: Typical Applications
Indicators On/Off Push Button/Test Switch One switch controls the power to your equipment. Upon power turn on, unit performs a self-test to detect overload or undercharged conditions. Turn on the UPS Press and hold the push button switch depressed for more than one second. Release the switch after the audible beep is sounded. -
Page 8: Battery Replacement Procedure
RJ11 Phone/Fax Protection Connectors USB Communication Port The provided LanSafe monitoring and shutdown software can be automatically configured to save your files and shut down your computer in the event of a prolonged power outage. Your personal computer can receive the status as utility power line, utility power failure, on battery and low battery by contact closure signals that are sent through the USB port. -
Page 9: Status Indicators
700VA model (12V- 7Ah battery) Status Indicators The UPS provides both visual and audible status indicators. Visual indicators consist of three LEDs to represent the following conditions: On utility power operation On battery power operation UPS fault/alarm UserÊs Manual 350-700VA Rev B... -
Page 10: Led And Alarm Status Table
LED & Alarm Status Table UPS status Self test Charging Charge off AC (Utility mode Low battery Over load Normal DC (Battery Over load Mode) Low battery Short/Fault/DC Over-Bat AC Over-Bat/Bat Fault Notes: Blink 1: ON 0.5 seconds / OFF 0.5 seconds Blink 2: ON 0.25 seconds / OFF 0.25 seconds B1: 1 beep / 5 seconds ON 0.25 seconds / OFF 4.75 seconds B3: 2 beeps / 5 seconds ON, 0.25 seconds / OFF 0.25 seconds 2 times 4 seconds OFF... -
Page 11: Troubleshooting
Troubleshooting Symptom UPS will not turn on UPS is making a continuous sound and the „Overload‰ indicator is lighted. UPS does not provide expected runtime. Connected equipment loses power while connected to the UPS Service and Support For questions and/or problems, please call your local distributor or the help desk and ask for a UPS technical representative. - Page 12 Head Office Eaton Power Quality Pty Ltd ABN 82 054 056 709 10 Kent Road, Mascot NSW 2020 Sales Offices Queensland Victoria Western Australia/NT South Australia Sales Phone: 1300 UPS UPS Sales Email: info.au@powerware.com National Service Centre: 1300 303 059 www.powerware.com.au UserÊs Manual 350-700VA Rev B...