model: PROFESSIONAL v2
GSM Antenna
VALET
micro-USB
button
SIM 2
SIM 1
GSM
LED
Fuse of the XP9
Temperature
socket
(5 )
sensor
DS18B20
Connection
GND
of additional
DQ
temperature
+5V
sensors
Dallas Semiconductor DS 18B20
Programming menu
Level 1
Recording remote controls (D800/
D670/D030/R465)/radio tags (BT760)
Level 2
Changing the factory preset
of the service PIN-code
Level 3
Recording the idle speed (rpm)
to the system memory
Level 4
Resetting to the factory settings
Level 5
Recording a Bluetooth engine
compartment module (RHM-03BT)
Level 6, 7
Recording Bluetooth radio
relays
1,
2 (BTR-101)
Level 8
Recording a Bluetooth GPS/GLONASS
receiver (NAV-035BT)
Programming and con guring
Level 11
an "Immobilizer PIN-code"
Level 15
Emergency deactivating immobilizer
radio tags
Level 16
Updating rmware of the built-in
Bluetooth modem
Level 17
Programming bypass of an original
immobilizer
Level 18
Pairing and unpairing a mobile device
Level 19, 20
Updating rmware of radio
relays
1,
2 (BTR-101)
Level 21
Updating rmware of an engine
compartment module (RHM-03BT)
Level 22
Updating rmware of a GPS/GLONASS
receiver (NAV-035BT)
Level 23, 24
Recording door sensors
1,
(DMS-100BT)
Level 25, 26
Updating rmware of door
sensors
1,
2 (DMS-100BT)
Level 27
Recording additional modules
(DI-04, BT-01)
Level 28
Updating rmware of additional
modules (DI-04/BT-01)
EXAMPLES OF RECORDING ADDITIONAL DEVICES
WARNING!
The additional devices that are included in the
system set have been already recorded in the system memory
(see the "System set" section of the user manual).
To record additional devices, enter a required level of the
programming menu. Perform a recording procedure in accordance
with a device manual. To save the recorded device, press the VALET
button once. The series of red and green ashes of the LED indicator
will con rm saving.
Recording remote controls (D800/D670/D030/R465):
Press and hold three buttons of a remote control (arm/disarm/F)
simultaneously for 1 second (until a short beep from the main
remote control or until fading a LED of an additional remote control),
then release the buttons. If recording was successful, the main
remote control will emit 2 short beeps and a siren of the base unit
will emit 1 beep. After this you can move to recording the next
remote control or radio tag.
Recording a radio tag (BT760):
Press the control button on a tag and hold it for 6 seconds (6 ashes
of the tag status indicator), release the button after the sixth ash. If
Warning!
XP3 is a multifunctional IMMO-KEY port. It is used only for
bypass of an original immobilizer. It connects in accordance with an
installation manual from the Pandora Alarm Studio.
XP3
X 2
XP6
8
16
7
15
6
14
5
13
4
12
3
11
2
10
1
9
XP8
3
6
2
5
1
4
XP7
5
10
4
9
3
8
2
7
1
6
XP9
4
1
5
2
6
3
2
the recording was successful, a siren will emit 1 beep, after this
you can move to recording the next tag.
(RHM-03 BT)
• Connect the wire 4 ("LIN output/Programming") and wire 5
("Ground"). Connect them to a grounded spot of a car.
• Apply +12V to the wire 7 ("+12V Power supply of the module").
• The system will con rm recording of the module to the system
memory with 1 beep of the siren.
• Disconnect the wire 4 ("LIN output/Programming") from the wire 5
and insulate it.
Level 6, 7 – Recording Bluetooth radio relays
• Connect the wire 1 ("Ground") to a grounded spot of a car.
• Connect the wire 3 ("Programming") and wire 4 ("+12V Power
supply of the radio relay"). Connect them to +12V.
• The system will con rm recording of the radio relay to the system
memory with 1 beep of the siren.
• Disconnect the wire 3 ("LIN output/Programming") from the wire 4
and insulate it.
WIRING DIAGRAM
WARNING!
choose a car model in the ALARM STUDIO (CAN-bus protocol).
WARNING!
4
Red
IMMO-KEY2 IN
is not powered.
3
Black
IMMO-KEY2 OUT
WARNING!
2
White
IMMO-KEY1 IN
powered through the base unit of the system should have
their own fuses.
1
Green
IMMO-KEY1 OUT
WARNING!
maintenance. In case of malfunction it should be taken to a
specialized service center.
External VALET button
16
Green/Orange
15
Gray/Black
14
Orange/Blue
13
White/Blue
12
White/Green
11
Brown/Yellow
10
Brown
9
Pink
8
Black
7
Gray/White
6
White
5
Brown/Black
4
Red/Black
3
Green
2
Yellow/White
1
Black/White
Relay module RMD-5M
+ 12V
6
Red
(+)
CH2 Ignition
3
Brown
(–)
CH14 Starter
5
Yellow
(–)
CH5
Brake pedal*
2
Orange
(–)
CH11 Bypass
4
Green
(–)
CH9 N.O. Blocking
1
Blue
(–)
* For remote engine start implementation
with the "Start/Stop button" logic
** Total current of the relays R3+R4+R5
cannot be more than 40A
10
Blue
200 mA (-)
9
200 mA (-)
Blue/Black
8
(-)
Brown/White
7
Yellow/Black
6
Orange/Black
5
Green/Blue
4
Green/Black
3
(+)
Yellow
2
Yellow/White
1
Orange/White
1
2A(+)
Gray/Red
2
2A(+)
Gray/Black
3
Black
4
Gray
2A(+)
5
Purple
2A(+)
6
Red
Total current of the channels CH17, CH18, CH19, CH20 cannot be more than 5A
(NAV-035BT)
• Connect the wire 2 ("Ground") to a grounded spot of a car.
• Apply +12V to the wire 1 ("+12V Power supply of the receiver").
• The system will con rm recording of the receiver to the system
memory with 1 beep of the siren.
Level 18 – Pairing and unpairing a mobile device
Pairing mobile device:
The LED indicator will light green after entering the level. Open the
mobile application, press the "Search device" button. The application
will search for the system via Bluetooth connection. Select the found
1,
2 (BTR-101)
system, the system and the mobile device will be automatically
paired. The system will con rm pairing with a sound signal of the
siren and a red light of the LED indicator.
Unpairing mobile device:
The LED indicator will light red after entering the level. Press the
VALET button and hold it for more than 4 seconds, release the
button. The system will con rm deleting with the series of sound
signals of the siren and the system will return to mobile device
registration mode (the LED indicator will light green).
Before starting the installation of the system,
A SIM card must only be inserted while the system
All power circuits of additional devices that are not
The security system does not require regular
LIN1 - Output "Reading and control a car"
LIN2 - "Webasto/Eberspaecher"
(+)
INP2 - Input "Brake pedal"
(-)
INP8 - Input "Neutral/Handbrake"
200mA (-)
INP6/
7
- Input "Trunk"
200mA (-)
INP4/
1
- Input "Doors"
200mA (-)
15 - Output "Comfort (closing windows)"
LIN1 - Input "Reading and control a car"
Input "Tachometer"
(+)
INP1- Input "Fuel level"
(see the back side)
200mA (-)
4/INP3
- Output "Beeper"
200mA (-)
3/INP7
- Output "Ignition 1"
200mA (-)
16 - Output "Switching o ACC (simulation of opening a door)"
200mA (-)
13 - Output "Blocking original radio channel"
Brown
Yellow
Orange
Green/Red
Blue/Red
R5
R4
R3
20A
R2
R1
Blue
Blue/Black
Green
Green/Black
40
Red
CH10 - Output "N.O. blocking"
6 - Output "Opening the central lock"
INP5 - Input "Front hood"
CH12 - Output "Turn indicators"
200mA (-)
CH8 - Output "Closing the central lock"
200mA (-)
INP9 - Input "Ignition"
CAN1
CH17 - Output "Radar detector"
CH20 - Output "Video Recorder"
CH18 - Output "Turn indicators"
CH 19 - Output "Siren"
Level 23,24 – Recording door sensors
• Insert a battery in the sensor.
• The system will con rm recording of the sensor to the system
memory with 1 beep of the siren.
Recording a radio module (DI-04):
• Connect power supply of the module.
• Press and hold the "VALET DI" button for 6 seconds. Release the
button after the sixth ash of the "LED DI".
• The system will con rm recording of the module to the system
memory with 1 beep of the siren.
Recording a radio relay (BT-01):
• Connect the wire 5 ("Ground") to a grounded spot of a car.
• Apply +12V to the wire 1 ("+12V Power supply of the relay").
• The system will con rm recording of the module to the system
memory with 1 beep of the siren.
WARNING!
Do not shield the built-in antennas.
IT IS FORBIDEN
to install the system on a car with
normal voltage other than 12V.
IT IS FORBIDEN
to bypass original fuses of a
security system in the installation process.
IT IS FORBIDEN
to install the security system with
damaged output cables.
CAN3
(-)
CAN3-L
+12V
R1
R2
R3
R4
R5
20A
20A**
20A**
20A**
Relay
module
To original
wires
CAN2
CAN2-H
CAN1-H
CAN2-L
CAN1-L
1,
2 (DMS-100BT)
Need help?
Do you have a question about the Professional v2 and is the answer not in the manual?
Questions and answers