Table of Contents
Advertisement
Quick Links
Non-Submersible Sump Pump
Class I, Group D & Class II, Groups E, F & G
IMPORTANT!
Read all instructions in this manual before operating pump.
As a result of Crane Pumps & Systems, Inc., constant product improvement program,
product changes may occur. As such Crane Pumps & Systems reserves the right to
change product without prior written notifi cation.
A Crane Co. Company
420 Third Street
Piqua, Ohio 45356
Phone: (937) 778-8947
Fax: (937) 773-7157
www.cranepumps.com
Manual Index
BARNES
BARNES
INSTALLATION MANUAL
Series: 1100EXP
1/3 HP, 1750 RPM, 60 Hz.
83 West Drive, Bramton
Ontario, Canada L6T 2J6
Phone: (905) 457-6223
Fax: (905) 457-2650
®
1148EXP
Form No. 094685-Rev. E
Advertisement
Table of Contents
Related Manuals for Crane Barnes 1100EXP Series
Summary of Contents for Crane Barnes 1100EXP Series
- Page 1 Read all instructions in this manual before operating pump. As a result of Crane Pumps & Systems, Inc., constant product improvement program, product changes may occur. As such Crane Pumps & Systems reserves the right to change product without prior written notifi cation.
-
Page 2: Safety First
Other brand and product names are trademarks or registered trademarks of their respective holders. ® Barnes is a registered trademark of Crane Pumps & Systems, Inc. 1995, 1996, 1998, 2002, 3/06 Alteration Rights Reserved... -
Page 3: Pump Specifications
PUMP SPECIFICATIONS: DISCHARGE ..... 1¼” NPT, Female, Vertical CORD ........NOT SUPPLIED LIQUID TEMPERATURE ... 150°F (66°C) Continuous MTR - UPPER BEARING ..Single Row, Ball VOLUTE ......Bronze MTR - LOWER BEARING ..Single Row, Ball BASE ......... Bronze PEDESTAL BEARING ...Sleeve COLUMN ...... -
Page 4: Section B: General Information
B-4) Service Centers: C-3) Electrical Connections: For the location of the nearest Barnes Service Center, check your Barnes representative or Crane Pumps & Systems, Inc., C-3.1) Power Cable: Service Department in Piqua, Ohio, telephone (937) 778-8947 or Crane Pumps & Systems Canada, Inc., Bramton, Ontario, (905) 457-6223. - Page 5 C-3.2) Overload Protection: C-5) Maintenance: Automatic thermal overload protects the sealed-in-oil Clean strainer at base of pump periodically to maintain motor, running dry may overheat the motor and trip the best performance. overload. The type of in-winding overload protector used No lubrication is required for the liquid end of the is referred to as an inherent overheating protector and pump.
-
Page 6: Section: D Warranty Repair
SECTION: D WARRANTY REPAIR ALWAYS furnish the following information: 1. Pump Part number. 2. Pump Serial number D-2 MODEL NUMBER: This designation consist of numbers and letters which represents the pump design. This number is used for ordering and obtaining information. D-3 SERIAL NUMBER: The Serial Number block will consist of a six digit number, which is specifi... -
Page 7: Troubleshooting
TROUBLE SHOOTING CAUTION ! Always disconnect the pump from the electrical power source before handling. If the system fails to operate properly, carefully read instructions and perform maintenance recommendations. If operating problems persist, the following chart may be of assistance in identifying and correcting them: MATCH “CAUSE”... -
Page 9: Parts List
PARTS LIST ITEM QTY. PART NO. DESCRIPTION 23240 Switch 23225M Motor 08182 Set Screw 5/16-18 x .38” Lg, Stainless 23204 Coupling 20669 Screen 09379 Stop Collar 23152-23.00 Float Rod, 23.00” 1100EXP 23152-47.00 Float Rod, 47.00” 1148EXP 09403 Slotted Hd Set Screw 1/4-20 x .25”... - Page 10 Limited 24 Month Warranty Crane Pumps & Systems warrants that products of our manufacture will be free of defects in material and workmanship under normal use and service for twenty-four (24) months after manufacture date, when installed and maintained in accordance with our instructions.This warranty gives you specifi c legal rights, and there may also be other rights which vary from state to state.
- Page 11 Crane Pumps & Systems, Inc. Distributor. RETURNED GOODS RETURN OF MERCHANDISE REQUIRES A “RETURNED GOODS AUTHORIZATION”. CONTACT YOUR LOCAL CRANE PUMPS & SYSTEMS, INC. DISTRIBUTOR. Products Returned Must Be Cleaned, Sanitized, Or Decontaminated As Necessary Prior To Shipment, To Insure That Employees Will Not Be Exposed To Health Hazards In Handling Said Material.
- Page 12 Notes...
Need help?
Do you have a question about the Barnes 1100EXP Series and is the answer not in the manual?
Questions and answers