Summary of Contents for GlammFire KIT Glamm 3D Plus 250
Page 1
KIT Glamm 3D Plus 250 Capacity 0,65 (filtered water) Autonomy 4 hours Voltage 220/240 V Frequency 50 Hz The product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility (EMC) EN55014, EN60555-2 and EN60555-3 These cover the essential requirements of EEC Directives...
10—After-sales service 11—Warranty Congratulations on purchasing your GlammFire Electric appliance. This quality product has been designed with preci- sion and rigour that characterizes us to offer you pleasant and soothing moments. Please read the instructions for use carefully and effective before using the appliance.
Page 4
Fig. 1 Fig. 1 Dimensions for installation Model Kit Glamm 3D Plus 250 281 mm 150 mm 281 mm Note: It’s importante that at least one side has openings to permit ventilation of the product.
Sump Model base Introduction Thank you for choosing this Glammfire electric fire. Please read this information guide carefully to be able to safely install, use and maintain your product. 2—Important safety advice When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electrical...
Page 9
GlammFire. PAG./9 PLUG POSITIONING The appliance must be positioned so that the plug is accessible. Keep the supply cord away from the front of the appliance. UNPLUGGING In the event of a fault unplug the device. Unplug the device when not required for long periods.
3—General information Only use decalcified/filtered water in this appliance. This applliance is intended for table top, worktop and furniture type fittings Always ensure that the appliance is sitting on a level surface. Once installed, never move this appliance or lay on its back, without draining the water from sump and water tank. If you intend not using the appliance for longer than 2 weeks, drain the water from sump and water tank and dry the sump.
GlammFire. PAG./11 Connecting the transducer unit: Lift off the metal bed and place carefully on the table/worktop - see Fig 3. Remove the water tank by lifting upwards and outwards - see Fig 6. Remove the nozzle by unclipping (1) and lifting upwards and outwards (2) - see Fig 7.
6—Maintenence General tips Only use filtered/decalcified water in this appliance. Always ensure that the appliance is sitting on a level surface. If you intend not using the appliance for longer than 2 weeks, remove and empty the sump and water tank. Once installed, never move this appliance or lay on its back, without draining the water from sump.
GlammFire. PAG./13 Air filte Lift the metal bed and place carefully on the table/worktop - see Fig. 3. Gently slide the air filter upwards out of its plastic holder - see Fig. 12. Gently rinse with water in the sink and dry with fabric towel before returning.
If the product fails during normal and proper use (not considering the above mentioned events) within the warranty period, GlammFire will replace the product free of charge. Our warranty is offered as an addition to your statutory rights. It is applicable to the original purchaser only, non- transferable.
Page 15
Name and Address of the Distributor The GlammFire is always concerned with the environment. This is reflected when the projection of their products and their packaging. Focusing on the reduction of energy consumption, raw materials, natural resources and quantity of waste generated, GlammFire follows the policy of the 4R's (Reduce, Reuse, Recycle and Recover).
Page 16
Recuperadores Pachinha Lda. Zona Industrial da Lagoa, Lote G1 4950-850 CORTES - MONÇÃO PORTUGAL Tel(+351) 251 654 800 Fax(+351) 251 654 801 info@glammfire.com www.glammfire.com PT13328-A-EN...
Need help?
Do you have a question about the KIT Glamm 3D Plus 250 and is the answer not in the manual?
Questions and answers