Husqvarna AUTOMOWER 420 Operator's Manual page 32

2. Use the arrow buttons and the OK button to move
through the menu structure
Reset all user settings .
3. Use the right arrow button to select
reset of all user settings?
4. Push the OK button to reset all the user settings.
Note:
Security level, PIN code, Loop signal,
Messages, Date & Time, Language and Country
settings are not reset.
The About menu
About menu displays information about the product,
The
for example serial number and firmware versions.
3.13.9 Accessories
Settings for accessories mounted on the product can be
made in this menu.
3.13.9.1 Information
This menu handles accessories mounted on the
product. Contact your local Husqvarna representative for
more information on available accessories.
3.13.9.2 Automower ® Connect
The product can connect to mobile devices that have the
®
Automower Connect app installed. The Automower
Connect app has Long-range cellular connectivity and
®
Short-range Bluetooth connectivity. Refer to
®
Automower Connect app on page 23 .
Note:
®
Automower Connect is always connected to
your product while the mobile device have connection
with the mobile network and the product is switched on.
Note:
All countries do not support Automower
Connect because of regional specified cellular systems.
®
The included Automower Connect life-time service only
applies if there is a third part sub-supplier of 2G/3G/4G
available in the operational area. In some countries
®
Bluetooth is not available because of legal reasons.
To enable the GeoFence function
GeoFence is a GPS-based theft protection that makes a
virtual fence for the product. You will get a message if
the product is moved on the other side of the GeoFence.
1. Put the product in the center of the work area.
To get access to the menu in the
2. Do steps 1–3 in
display of the product on page 24 .
32 - Installation
3.
Settings > General >
Proceed with
4.
5.
To set a new center point for the Geofence function
1.
2.
3.
4.
To set the GeoFence level of sensitivity
The higher level of GeoFence sensitivity, the easier the
alarm starts.
1.
2.
3.
4.
To use the SMS function
The SMS function sends you an SMS when the product
®
is moved out of the GeoFence.
1.
2.
3.
4.
®
5.
6.
Note:
from the product.
Use the arrow buttons and the OK button to move
through the menu structure Accessories >
Automower Connect > GeoFence > Activate
GeoFence .
Push the OK button.
Select Activate GeoFence and push the OK
button.
Put the product in the center of the work area.
To get access to the menu in the
Do steps 1–3 in
display of the product on page 24 .
Use the arrow buttons and the OK button to move
Accessories >
through the menu structure
Automower Connect > GeoFence > New center
point .
Push the OK button.
To get access to the menu in the
Do steps 1–3 in
display of the product on page 24 .
Use the arrow buttons and the OK button to move
through the menu structure Accessories >
Automower Connect > GeoFence .
Use the arrow buttons to select level of GeoFence
sensitivity.
Push the BACK button.
To get access to the menu in the
Do steps 1–3 in
display of the product on page 24 .
Use the arrow buttons and the OK button to move
through the menu structure Accessories >
Automower Connect > Communication > Use
SMS .
Push the OK button.
Use the arrow buttons and the OK button to move
Accessories >
through the menu structure
Automower Connect > Communication > SMS
phone numbers .
Push the number buttons to enter the telephone
number with country code. For example
(+)46701234567.
Push the BACK button.
There is a maximum of 10 SMS each month
1201 - 005 - 19.03.2021