Husqvarna AUTOMOWER 420 Operator's Manual page 30

5. Use the number buttons to select how frequently
the product must use each sector. Set in
percentage.
6. Push the BACK button.
3.13.7.5 Reversing distance
The reversing distance makes the product move in
reverse for a set distance, before the product starts to
cut the lawn. The factory setting is 60 cm / 2 ft.
To set the reversing distance
To get access to the menu in the
1. Do steps 1-3 in
display of the product on page 24 .
2. Use the arrow button and the OK button to move
through the menu structure
> Reversing distance .
3. Use the number buttons to set the distance.
4. Push the BACK button.
3.13.7.6 Drive Past Wire function
The front of the product always moves past the
boundary wire by a specified distance. Then the product
moves rearward and changes direction. The factory
setting is 31 cm / 13 in. You can select a distance of
20-50 cm / 10-15 in.
Note:
If you change the distance for
the distance will change along the boundary wire in all
parts of the work area.
To set the Drive Past Wire function
To get access to the menu in the
1. Do steps 1–3 in
display of the product on page 24 .
2. Use the arrow button and the OK button to move
through the menu structure
> Drive Past Wire .
3. Use the number buttons to set the distance.
4. Push the BACK button.
3.13.8 Settings
In settings you can change the general settings to your
product.
3.13.8.1 Profiles
With the function Profiles, different sets of product
settings can be saved. This can be used when one
product is used for more than one work areas and
charging stations. The product settings and the pairing
with the charging stations are saved in the profile and
can easily be used again.
30 - Installation
To save settings to a profile
1.
2.
3.
4.
If settings have been changed but not saved, the symbol
* is shown beside the profile name.
To change the name of a profile
Installation > Advanced
1.
2.
3.
4.
To use a profile
1.
Drive Past Wire ,
2.
3.
To connect a new charging station to a profile
1.
Installation > Advanced
2.
3.
4.
3.13.8.2 ECO mode
If
boundary loop, the guide wire and the charging station,
when the product is parked or is charging.
Note:
interference with other equipment, for example hearing
loops or garage doors.
Do steps 1–3 in To get access to the menu in the
display of the product on page 24 .
Use the arrow buttons and the OK button to move
through the menu structure
Use profiles > Profile A, B, C.
Use the arrow buttons and the OK button to select
and save the profile.
Push the BACK button.
Do steps 1–3 in To get access to the menu in the
display of the product on page 24 .
Use the arrow buttons and the OK button to move
through the menu structure Settings
Use profiles > Profile A, B, C. > Rename.
Use the arrow buttons and the OK button to select
letters.
Push the BACK button to save the new profile
name.
Do steps 1–3 in To get access to the menu in the
display of the product on page 24 .
Use the arrow buttons and the OK button to move
through the menu structure
Use profiles > Profile A, B, C > Select.
Push the BACK button.
Save the settings in a profile to be used with the
original charging station. Do steps 1–4 in
settings to a profile on page 30 .
Put the product in the new charging station.
Use the arrow buttons and the OK button to move
through the menu structure
New loop signal .
Save a profile for the new charging station, or
select a profile in the list. Do steps 1–4 in
settings to a profile on page 30 , or do steps 1–3 in
To use a profile on page 30 .
ECO mode is activated, it switches off the signal in the
ECO mode to save energy and avoid
Use
Settings > Profiles >
> Profiles >
Settings > Profiles >
To save
Security > Advanced >
To save
1201 - 005 - 19.03.2021