Husqvarna AUTOMOWER 420 Operator's Manual page 31

Note:
To start the product manually in the work area,
push the STOP button before you remove the product
from the charging station. If not, the product can not be
started in the work area.
To set the ECO mode
To get access to the menu in the
1. Do steps 1–3 in
display of the product on page 24 .
2. Use the arrow buttons and the OK button to move
through the menu structure
3. Push the OK button to select the
4. Push the BACK button.
3.13.8.3 Spiral Cutting
The product cuts the grass in a spiral pattern if the grass
Spiral cutting can be set in 5 levels:
is longer in an area.
• Low-
• Low
• Mid
• High
• High+
The level sets how sensitive the product is to changes in
grass height.
Note:
Spiral cutting is only started in the Main area
Secondary area mode does not let
mode. Cutting in the
Spiral cutting . Spiral Cutting does not
the product to start
start in slopes steeper than 15%.
To set the Spiral Cutting
1. Do steps 1–3 in To get access to the menu in the
display of the product on page 24 .
2. Use the arrow buttons and the OK button to move
through the menu structure
Cutting > Use Spiral Cutting .
3. Push the BACK button.
To set the level of Spiral Cutting
1. Do steps 1–3 in To get access to the menu in the
display of the product on page 24 .
2. Use the arrow buttons and the OK button to move
through the menu structure
Cutting > Use Spiral Cutting > Intensity .
3. Use the left arrow button to select the level of the
Spiral Cutting.
4. Push the BACK button.
3.13.8.4 Slope control
In order to decrease lawn wear near the boundary wire
in slopes, the product prevents to move in the opposite
direction when the product operates in a slope.
control is enabled in the factory settings.
1201 - 005 - 19.03.2021
To set the Slope control
1.
2.
3.
3.13.8.5 General
In
product.
Settings > ECO mode .
ECO mode .
To set the time & date
1.
2.
3.
4.
5.
6.
To set the language
1.
2.
3.
To set the Country & Timezone
Settings > Spiral
1.
2.
3.
Settings > Spiral
To set the unit format
1.
2.
3.
Slope
To reset all user settings
1.
Do steps 1–3 in To get access to the menu in the
display of the product on page 24 .
Use the arrow buttons and the OK button to move
through the menu structure
control > Use Slope control .
Push the BACK button.
General you can change the general settings of the
Do steps 1–3 in To get access to the menu in the
display of the product on page 24 .
Use the arrow buttons and the OK button to move
through the menu structure
Time & Date .
Use the number buttons to set the time and then
push the BACK button.
Use the number buttons to set the date and then
push the BACK button.
Use the arrow buttons to set the time format and
then push the BACK button.
Use the arrow buttons to set the date format and
then push the BACK button.
To get access to the menu in the
Do steps 1–3 in
display of the product on page 24 .
Use the arrow buttons and the OK button to move
through the menu structure
Language.
Use the arrow buttons to select language and then
push the BACK button.
To get access to the menu in the
Do steps 1–3 in
display of the product on page 24 .
Use the arrow buttons and the OK button to move
through the menu structure
Country & Timezone.
Use the arrow buttons to select country and then
push the BACK button.
To get access to the menu in the
Do steps 1–3 in
display of the product on page 24 .
Use the arrow buttons and the OK button to move
through the menu structure
Unit format.
Use the arrow buttons to select unit format and
then push the BACK button.
Do steps 1–3 in To get access to the menu in the
display of the product on page 24 .
Settings > Slope
Settings > General >
Settings > General >
Settings > General >
Settings > General >
Installation - 31