Table of Contents
Advertisement
OPERATING MANUAL
7 1/4" Circular Saw with Laser Line
54-8347-0
Specifications:
Motor:
No-load speed:
Blade:
Cutting angle:
Depth of cut at 90°:
Depth of cut at 45°:
Laser :
Wavelength:
Maximum output:
Weight:
IMPORTANT:
Read through this operating manual carefully before using your new tool. Pay close attention
to all Safety Instructions, Warnings, and Caution sections. Use your tool properly, and
only for its intended purpose.
Safety symbols in this manual are used to indicate possible dangers. The safety
symbols and their explanations require your full understanding. The safety warnings do not
eliminate any danger by themselves, and they are not substitutes for proper accident
prevention measures.
This Safety Alert Symbol indicates caution, warning, or danger. Failure to obey a
safety warning can result in serious injury to yourself or to others. To reduce the risk of injury,
fire, or electric shock, always follow the safety precautions.
120 V 60 Hz 14 A
5500 RPM
7 1/4"(24-tooth)
0-45°
2 1/2" (63.5 mm)
1 13/16" (46 mm)
Class IIIa
650 nm
≤2.5 mW
11 lb 2 oz (5.05 kg)
1
Advertisement
Table of Contents
Related Manuals for MasterCraft Hawkeye Laser 54-8347-0
Summary of Contents for MasterCraft Hawkeye Laser 54-8347-0
- Page 1 OPERATING MANUAL 7 1/4" Circular Saw with Laser Line 54-8347-0 Specifications: Motor: 120 V 60 Hz 14 A No-load speed: 5500 RPM Blade: 7 1/4"(24-tooth) Cutting angle: 0-45° Depth of cut at 90°: 2 1/2" (63.5 mm) Depth of cut at 45°: 1 13/16"...
-
Page 2: General Safety Precautions
RULES FOR SAFE OPERATION KNOW YOUR TOOL Before operating this tool, carefully read this operating manual and all of the labels affixed to the circular saw. Keep this manual available for future reference. IMPORTANT This tool should only be serviced by a qualified service technician. READ ALL INSTRUCTIONS THOROUGHLY GENERAL SAFETY PRECAUTIONS Keep your work area clean and well-lit. -
Page 3: Electrical Safety
WARNING: When using power tools, basic safety precautions should always be followed in order to reduce the risk of fire, electric shock, and personal injury. Stay alert, watch what you are doing, and use common sense when operating a power tool. -
Page 4: Additional Safety Rules For Laser Lights
“W-A” or “W”. These cords are rated for outdoor use, and reduce the risk of electric shock. • Replace damaged cords immediately. Use of damaged cords can lead to shocks, burns, or electrocution. • If an extension cord is required, use a cord with the proper size of conductors in order to prevent excessive voltage drop, loss of power, or overheating. - Page 5 CAUTION: Using controls or adjustments or performing procedures other than those specified herein may result in hazardous radiation exposure. SPECIFIC SAFETY RULES FOR CIRCULAR SAW WARNING: Keep your hands away from the cutting area and the blade. Keep your second hand on the auxiliary handle or the motor housing. If both hands are holding the saw, they cannot be cut by the blade.
- Page 6 comes to a complete stop. Never attempt to remove the saw from the work or pull the saw backward while the blade is in motion, or KICKBACK may occur. Investigate and take corrective actions to eliminate the cause of blade binding. •...
- Page 7 Fig.2 On/off trigger switch with lock-off button Spindle lock button Main handle Front handle Lower blade guard Blade guard lever Depth locking lever Angle locking knob 0−45° bevel gauge 10. Hexagon bolt 11. Base plate 12. Flange 13. Parallel fence guide 14.
-
Page 8: Assembly And Adjustments
ASSEMBLY AND ADJUSTMENTS WARNING: Remove the circular saw from the carton, and examine it carefully. Do not discard the carton or any packaging material until all parts are examined. WARNING: If any part of the saw is missing or damaged, do not plug the circular saw in until the damaged part is repaired or replaced. -
Page 9: Maintenance
LASER LINE Gently depress the laser switch to activate the laser line. LASER APERTURE When the laser line is switched on, an intense narrow beam of pure red light is emitted from the laser aperture. The line shines along the workpiece in order to guide you as you cut. The line is clearly visible, and will not be obscured by sawdust. -
Page 10: Warranty
WARRANTY This Mastercraft product carries a three (3) year replacement warranty against defects in workmanship and materials. At its discretion, Mastercraft Canada agrees to have any defective part(s) repaired or replaced free of charge, within the stated warranty period, when returned by the original purchaser with proof of purchase.
Need help?
Do you have a question about the Hawkeye Laser 54-8347-0 and is the answer not in the manual?
Questions and answers