Sign In
Upload
Download
Table of Contents
Contents
Add to my manuals
Delete from my manuals
Share
URL of this page:
HTML Link:
Bookmark this page
Add
Manual will be automatically added to "My Manuals"
Print this page
×
Bookmark added
×
Added to my manuals
Manuals
Brands
Besam Manuals
Door Opening System
AAE977
Installation manual
Besam AAE977 Installation Manual
Hide thumbs
1
Table Of Contents
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
page
of
16
Go
/
16
Contents
Table of Contents
Troubleshooting
Bookmarks
Table of Contents
Table of Contents
Important Information
Technical Specifications
Component Identification
Electrical Installation
Initial Sensor Setup
Mechanical Adjustments
Remote Control
1-Way Traffic Setup
Manual Setup
Troubleshooting
Retrofit Installation
Standard Inputs Vs. Auxiliary Inputs
Advertisement
Quick Links
Download this manual
Besam UltraView
Installation Manual
AAE977
Complies with ANSI/BHMA A156.10 Standard for Power Operated Pedestrian Doors. UL325 Listed
Ultraview US23-0640-09
07-30-09
V4
© Copyright 2009 Besam US Inc. May not be reprinted without permission
1
Table of
Contents
Previous
Page
Next
Page
1
2
3
4
5
Advertisement
Table of Contents
Related Manuals for Besam AAE977
Door Opening System Besam Swingmaster MP Installation, Adjustment And Maintenance Instructions
Swing door operator ik-a (concealed); bottom load & fire door (11 pages)
Door Opening System Besam OPB Manual
Swing door operator (9 pages)
Door Opening System Besam PowerSwing Manual
Swing door operator (43 pages)
Door Opening System Besam ASSA ABLOY Swingmaster 900 Service And Installation Manual
(68 pages)
Door Opening System Besam PowerSwing Installation Manual
(44 pages)
Door Opening System Besam SW200i Owner's Manual
Swing door operator (14 pages)
Door Opening System Besam SW200i Installation And Service Manual
Swing door operator (ohc) (82 pages)
Door Opening System Besam SW 100 Installation And Service Manual
Low energy swing door operator (50 pages)
Summary of Contents for Besam AAE977
Page 1
Besam UltraView Installation Manual AAE977 Complies with ANSI/BHMA A156.10 Standard for Power Operated Pedestrian Doors. UL325 Listed Ultraview US23-0640-09 07-30-09 © Copyright 2009 Besam US Inc. May not be reprinted without permission...
Page 2: Table Of Contents
This operator may be equipped with batteries containing materials that are hazardous to the environment. Remove the batteries from the operator before it is scrapped. The batteries must be disposed of safely. Ultraview US23-0640-09 07-30-09 © Copyright 2009 Besam US Inc. May not be reprinted without permission...
Page 3: Technical Specifications
Shape of the sensing field (choice of lens) Multiple functions (using push buttons). Multiple functions (using push buttons). Sensitivity Sensitivity Remote control adjustments Detection mode Auto-learn time Immunity Ultraview US23-0640-09 07-30-09 © Copyright 2009 Besam US Inc. May not be reprinted without permission...
Page 4: Component Identification
Based on Step 1, connect the appropriate extension harness to the appropriate connector on the Ultraview Interface Board. DIP SWITCH STOP/IMPULSE(BREAKOUT INPUT) STD/AUX SWITCH KNOWING ACT INPUT (AUX) Ultraview US23-0640-09 07-30-09 © Copyright 2009 Besam US Inc. May not be reprinted without permission...
Page 5: Initial Sensor Setup
6.Connect the break-out switch connector (see picture Step 1) and secure the header cover. 7.(Once the Unislide and Ultraview covers are installed and secured in place). Launch a final set-up via the remote control (magic wand 0) Ultraview US23-0640-09 07-30-09 © Copyright 2009 Besam US Inc. May not be reprinted without ermission...
Page 6: Mechanical Adjustments
45º will place the pattern farther away. Be certain to walk-test detection field and insure compliance with current applicable ANSI standards. ADJUST ANGLE BY TILTING MICROWAVE CELL Ultraview US23-0640-09 07-30-09 © Copyright 2009 Besam US Inc. May not be reprinted without permission...
Page 7
LED is flashing (the sensors are learning the influence of the door) - this will take approximately 16 seconds d.To adjust properly, follow the instructions on page 5, section 5c Ultraview US23-0640-09 07-30-09 © Copyright 2009 Besam US Inc. May not be reprinted without permission...
Page 8: Remote Control
- replace as necessary. Open the battery compartment at the back of the remote control. Insert 2 AAA batteries. Ultraview US23-0640-09 07-30-09 © Copyright 2009 Besam US Inc. May not be reprinted without permission...
Page 9: 1-Way Traffic Setup
(1 through 9 value ) Re-Entry Zone (0 through 9 value ) Normal microwave zone Ultraview US23-0640-09 07-30-09 © Copyright 2009 Besam US Inc. May not be reprinted without permission...
Page 10: Manual Setup
(e.g. for detection mode: 1, 2, 3, then 1, 2, …). 2.The sensor automatically returns to standard mode if neither button has been pressed for one minute. Ultraview US23-0640-09 07-30-09 © Copyright 2009 Besam US Inc. May not be reprinted without permission...
Page 11: Troubleshooting
1. System not properly set-up - Rapid flashing orange LED button next to the 5 position switch Time out 2.Check Sensor set-up (pg5 ) 3.Check electrical installation (pg4) Ultraview US23-0640-09 07-30-09 © Copyright 2009 Besam US Inc. May not be reprinted without permission...
Page 12: Retrofit Installation
1. Separate the cover from the unit by prying apart the attachment clips. PRY APART CLIPS QUICK-DISCONNECT HARNESS US02-0640-05 2.Remove the shroud from the sensor by squeezing with both hands on the shroud SQUEEZE SHROUD TO REMOVE Ultraview US23-0640-09 07-30-09 © Copyright 2009 Besam US Inc. May not be reprinted without permission...
Page 13: Standard Inputs Vs. Auxiliary Inputs
(or otherwise), then once the door is at a position other than fully closed, the Ultraview sensors will function with respect to the IR curtains, as well as according to the microwave Ultraview US23-0640-09 07-30-09 © Copyright 2009 Besam US Inc. May not be reprinted without permission...
Page 14
P2 also. 5) Designate P1 sensor (night mode) 6) Set 5 position switch to two-way 7) Set re-entry key on P1 Ultraview US23-0640-09 07-30-09 © Copyright 2009 Besam US Inc. May not be reprinted without permission...
Page 15
4.Setting the rotary switch to the OFF position will disable all inputs once the door is fully closed. Ultraview US23-0640-09 07-30-09 © Copyright 2009 Besam US Inc. May not be reprinted without permission...
Page 16
25.Note on the Planned Maintenance review any recommendations to improve door performance and reliability, and review with customer. Besam US Inc. 1900 Airport Road Monroe, NC 28110 Tel: (704) 290-5551, Fax: (704) 290-5555 Ultraview US23-0640-09 07-30-09 © Copyright 2009 Besam US Inc. May not be reprinted without permission...
Table of Contents
Print
Rename the bookmark
Delete bookmark?
Delete from my manuals?
Login
Sign In
OR
Sign in with Facebook
Sign in with Google
Upload manual
Upload from disk
Upload from URL