Webasto Dual Top ST 6 Operating Instructions Manual page 9

4.3.5 Setting desired interior temperature
You can set the desired interior temperature when the device is
switched on (see chapter 4.3.3, "Switching on the heater" on
page 8 ) and the status display is visible.*
The status display shows the motorhome and the current heat-
ing program. See Fig. 4.
Press to increase or
NOTE
The display shows the desired temperature, not the
actual interior temperature.
You can change the selected interior temperature, no
matter if the heater is ON or OFF. As soon as heater is
switched on (manually, by remote control or by timer)
in cabin heating mode, the device will heat interior and
keep it at this temperature.
* If the actual heating mode is initiated by remote control, the
desired interior temperature cannot be adjusted. The Dual Top
ST will heat up interior and keep the temperature at the preset
value selected when using the Telestart to set this.
4.3.6 Summer mode (hot water only)
Make sure that the boiler is filled with fresh drinking water.
For Dual Top ST 8: If you want the electric heater to provide hot
water, make sure to connect the external power supply (230
VAC): 230 V" (10) on the display.
Make sure the device is switched on.
1. Press MENU.
2. Press and to select "
3. Press OK.
4. Press and to select "
70°C".
5. Press OK. For Dual Top ST 6: The display shows "Selection
completed" .
6. For Dual Top ST 8: Press
source:
Dual Top ST 8
"Diesel powered"
"1000 W ~ 230 V"*
*Options: "...W ~ 230 V" shown only if external 230 V power
supply is connected.
8. Press OK. The display shows "Selection completed".
NOTE
When the heater is already "ON", the text "Selection
completed, press OK to change operation mode" is
displayed.
u
Press OK.
After 3 seconds the power indicator (6) lights up in green and
the display changes to:
9026381C Dual Top ST 6 _ 8 - OI
to decrease the desired temperature.
hot water".
Eco 40°C" or " Comfort
and to select the desired
230 V and ... W: only Dual Top ST 8.
For Dual Top ST 6:
– "Heater ON"
– " water 40°C" or "
– (depending on the selected water temperature)
– " diesel" or "
type and selected heat source).
The power indicator (6) lights green as long as there is a de-
mand for hot water. To end this press STOP.
4.3.7 Winter mode (heating without hot water
production)
For Dual Top ST 8: If you want the electric heater to provide hot
air, make sure to connect the external power supply (230 V AC):
" 230 V" (10) on display.
Make sure the device is switched on.
1. Press MENU.
2. Press and to select "
3. Press OK. For Dual Top ST 6: The display shows "Selection
completed".
4. For Dual Top ST 8: Press
heat source:
Dual Top ST 8
"Diesel powered"
"1000 W ~ 230 V" *
"2000 W ~ 230 V" *
"Diesel + 1000 W ~ 230 V" *
"Diesel + 2000 W ~ 230 V" *
* Options: "...W ~ 230 V" shown only if external 230 V power
supply is connected.
5. Press OK. The display shows "Selection completed".
NOTE
When the heater is already "ON", the text "Selection
completed, press OK to change operation mode" is
displayed.
u
Press OK.
After 3 seconds the power indicator (6) lights up in green and
the display changes to:
: only Dual Top ST 8
– "Heater ON"
– "Cabin", "... °C"
(the value depends on the selected interior temperature;
°C or °F depends on setting)
– " diesel", " 1000 W", "
on the heater type and on selected heat source).
Press or to adjust desired interior temperature.
Operating instructions | 4
water 70°C"
1000 W", (depending on the heater
Heating Cabin".
and to select the desired
2000 W" (depending
9 / 19