Download Print this page
Webasto Air Top Series Operating Instructions Manual
Webasto Air Top Series Operating Instructions Manual

Webasto Air Top Series Operating Instructions Manual

Hide thumbs Also See for Air Top Series:

Advertisement

Quick Links

Operating Instructions

Air Top Series Heaters
Introduction
Dear Webasto Customer,
Thank you for choosing a Webasto Air Top Series Heater.
Air Top Series Heaters are used
– to heat cabins, boats, trucks, minibuses, vans and motor-homes and
– to defrost vehicle windows.
We presume that the principle and mode of operation of your new heater has
been explained to your complete satisfaction by the workshop or service
center which installed the heater. In these operating instructions we would
like to once again provide you with an overview of the safe use of your new
heater.
Repair work should only be carried out by an authorized Webasto dealer.
Servicing and Safety Instructions
1. When the heater is in use, the surface of the hot air outlet will become hot to the touch.
Contact with skin may cause burns.
2. Webasto heaters must be switched "off" when re-fueling at gas stations and/or
while loading or unloading flammable materials for transport, to prevent the
risk of explosion.
3. The year in which the heater was used for the first time must be permanently displayed
on the factory plate by deleting the inapplicable years from the plate.
4. The heaters are not designed for heating hazardous substance transport
compartments.
5. Claims can only be made if it can be verified that the claimant has complied with the
servicing and safety instructions.
6. The heater may not be operated in enclosed spaces (such as garages) as a result
of the risk of poisoning and asphyxiation, even if a timer is used.
7. In the event of long-lasting heavy smoke development, unusual combustion noises or a
smell of fuel or if the heater suffers continuous fault cut-outs with error messages
(flashing code), it must be shut down by removing the fuse and must not be used until it
has been inspected by Webasto-trained personnel.
8. Wherever flammable vapors or dust may form, the heater must be switched off
as a result of the risk of explosion.
9. The heat transfer unit on air heaters is exposed to very high thermal stress and
must be replaced by a genuine Webasto spare part after a ten year life cycle.

Advertisement

loading
Need help?

Need help?

Do you have a question about the Air Top Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Webasto Air Top Series

  • Page 1: Operating Instructions

    8. Wherever flammable vapors or dust may form, the heater must be switched off as a result of the risk of explosion. 9. The heat transfer unit on air heaters is exposed to very high thermal stress and must be replaced by a genuine Webasto spare part after a ten year life cycle.
  • Page 2 10. The fuel specified by the vehicle manufacturer is suitable for use in an Air Top Series Heater B (gasoline). The diesel fuel specified by the vehicle manufacturer is suitable for use in an Air Top Series Heater D (diesel).
  • Page 3 Control Element Changes to the settings on the control element will be carried out with a short time delay Rotary knob for: - Switching on and off - Setting the room temperature - Resetting after a fault cut-out Indicator / error code display Switch On Set the rotary knob on the control element to the desired temperature.
  • Page 4 Heater ON Example Press the Webasto button to turn heater on. Set Temperature Output & Heater Runtime Example Using the rotary dial and the selection button, follow these steps to set your cab temperature to 70°F with a runtime of 4 hours.
  • Page 5 Set time and date using the rotary knob and selection 12 hour Time & Date button. 12 (AM / PM) or 24 hour available. The Webasto button can be used to go back to the previous field if additional changes are needed.
  • Page 6 Depending on the installation location, the temperature 0° Offset reading may vary slightly. The Offset feature allows a temperature adjustment of +/- 9°F (+/- 5°C). Adjust this as necessary to obtain the most accurate ambient temperature reading. Default allows the user to perform a factory reset of the Default control settings.
  • Page 7 If an error occurs, first check the fuse and plug connections to ensure that they are in proper condition and connected correctly. If the actions described below do not rectify the error, have the heater checked by Webasto- trained personnel.
  • Page 8 Error code output on combination timer or control element If the system is fitted with a combination timer, when an error occurs an error code is dis- played on the timer's screen until the heater has been properly repaired. The error code is output if the heater is fitted with a control element after an error has oc- curred by the switch-on indicator/error code indicator flashing.
  • Page 9 Heater Lock-out Reset Procedure Using switch or standard timer control, turn heater on Remove the main power connection to heater from battery or pull fuse for a minimum of 20 seconds. Using switch or standard timer control, turn the heater off. Reinstall main heater power connection where previously disconnected.
  • Page 10 Replacement parts are covered for six (6) months or the remainder of the original warranty period, whichever is longer. The intent of the Webasto warranty is to protect the original end-user of the heater from de- fects and provide free repair and replacement of defective parts in the manner provided here- in.
  • Page 11 Notes...
  • Page 12 Webasto Thermo & Comfort N.A., Inc 15083 North Road Fenton, MI 48430 Technical Assistance Hotline USA: (800) 860-7866 Canada: (800) 667-8900 www.webasto.us Org. 3/2017 P/N: 5012526A www.techwebasto.com...