Webasto Dual Top ST 6 Operating Instructions Manual page 12

4 | Operating instructions
10. Press OK. Selected day and hour appear on display. Matrix
with programmable hours and interior temperatures T1 and
T2 appears. Field of actual time and temperature blinks.
11. Press or to adjust desired temperature for selected
day and hour: OFF, T1 or T2.
12. Press OK.
13. Repeat step 11 and 12 until all 24 hours are programmed.
(The hour period is shown at the bottom of the display.)
14. Three seconds after you see "Programming successful" on
the display you can select another day as described in step
6, and continue to program remaining days. You can also
copy programmed values from one day to another. See
Daycopying, step 6.
When you have programmed all days, press BACK to return to
main menu.
Day copying
Instead of programming each day individually, you can copy
programmed values from one day to another.
After copying you can keep the identical values or make adjust-
ments (see Day setting, step 6).
If you copy days after setting temperatures T
gramming and setting a day, then start at step 6.
Make sure the device is switched on.
1. Press MENU.
2. Press and to select " Programming Timer".
3. Press OK.
4. Press and to select " Timer Program 1" or "
Timer Program 2" (values T
settings).
5. Press OK.
6. Press and to select "Set Monday", "Set Tuesday",
"Set Wednesday" etc...
7. Press OK.
8. Press and to select "Copy Tuesday", "Copy Wed-
nesday" etc...
9. Press OK.
10. The display shows: "Copy of 24 h program successful".
11. After 3 seconds, select another day as described in step 6
and continue to program remaining days.
12. When you have finished programming all days, then press
BACK to return to main menu.
4.5.2 Heating by timer
This paragraph describes how to select a program to heat the
interior and to provide hot water.
You can choose from 2 programs that define 7 days, 24 hours
interior and water heating.
12 / 19
and T , or pro-
1 2
and T depend on program
1 2
To change the programs see chapter 4.5.1, "Program setting"
on page 11 .
If you want the electric heater to provide hot air or hot water,
make sure you connect the external power supply (230 V AC): "
230 V" (10) on display.
Make sure the device is switched on.
1. Press MENU.
2. Press and to select " Heating by Timer".
3. Press OK.
4. Press and to select " Timer Program 1" or "
Timer Program 2" (values T1 and T2 depend on program
settings).
5. Press OK.
6. Press and to select "
Heating Cabin + Hot Water".
7. Press OK.
8. Press and to select the desired heat source:
Dual Top ST 8
"Diesel powered"
"1,000 W ~ 230 V" *
"2,000 W ~ 230 V" *
* Options "...W ~ 230 V" shown only when external 230 V
power supply is connected.
9. Press OK. The display shows "Selection completed".
NOTE
When the heater is already "ON", the text "Selection
completed, press OK to change operation mode" is
displayed.
u Press OK.
After 3 seconds the power indicator (6) lights up in green and
the display changes to:
230 V and ... W: Only Dual Top ST 8
– "Heater ON"
– "Water " (if "Hot Water" is selected)
– "Cabin"
– " diesel", " 1000 W", "
on heater type and selected heat source).
– Day
– Time
– Matrix with programmed hours and interior temperat-
ures. The actual time and temperature blink.
NOTE
Press and to view program settings of another
day.
Heating Cabin" or "
2000 W" (depending
9026381C Dual Top ST 6 _ 8 - OI