TP-Link EAP110 Installation Manual
Wireless n access point
Hide thumbs
Also See for EAP110:
- User manual (104 pages) ,
- Installation manual (84 pages) ,
- Quick setup manual (10 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for TP-Link EAP110
Summary of Contents for TP-Link EAP110
- Page 1 Installation Guide Wireless N Access Point EAP110/EAP120/EAP220...
-
Page 3: Table Of Contents
Specifications ——————————————————————— About This Installation Guide This guide is designed to familiarize you with the general layout of the EAP110, EAP120 and EAP220, describe how to perform the hardware installation, and how to configure the EAP Controller software in your network. Your EAP has more features and functionalities which can be found in the User Guide. -
Page 4: Network Topology
Network Topology A typical network topology for the EAP is shown below. Controller Host... -
Page 5: Hardware Overview
Hardware Overview 1. LED EAP110, EAP120 and EAP220 have the same LED status and corresponding indications. System LED LED Status Indication Solid green The device is working properly. Flashing red System errors. RAM, Flash, Ethernet, WLAN or firmware may be malfunctioning. - Page 6 CONSOLE ETHERNET ON/OFF POWER ARROW 1 Please note that EAP110 does not have the CONSOLE port, POWER port or ON/OFF button. The interface panel components of the EAP, from left to right, are described in the following list. Kensington Security Slot Secure the lock (not provided) into the security slot to prevent the device from being stolen.
- Page 7 Please refer to next chapter 2.Mounting Bracket to locate ARROW 2. ETHERNET For EAP110, this port is used to connect to the POE port of the provided PoE adapter for both data transmission and power supply through Ethernet cabling.
-
Page 8: Hardware Installation
Hardware Installation The EAP can be wall-mounted or ceiling-mounted. Please suitably arrange your wire layout before mounting the EAP. We take EAP110 as example to explain the installation. EAP110 can be powered via the provided PoE adapter, while EAP120 and EAP220 can be powered via a PoE switch or the provided power adapter. -
Page 9: Installation
3. Installation Ceiling Mounting ■ Note: Make sure the thickness of the ceiling is less than 18mm and ■ the ceiling can bear at least five kilograms. It is NOT recommended to mount the EAP on a low-strength ■ material, such as gypsum ceiling panel. If no other choice is available, make sure you add a piece of strong material under the wing nuts to ensure the EAP is mounted solidly. - Page 10 3. Use a drill with the appropriate size drill bit to drill three 4mm holes for the pan-head screws, and drill a 10mm hole for the Ethernet cable to feed through. 4mm hole for mounting bracket 10mm hole for Ethernet cable feed Secure the mounting bracket to the ceiling tile using the pan-head screws, washers and wing nuts, as shown below.
- Page 11 5. Attach the EAP to the mounting bracket by aligning ARROW 1 with ARROW 2, as shown below. ARROW 1 ARROW 2 6. Turn the EAP clockwise until it locks into place.
- Page 12 Feed the Ethernet cable through the hole and set the ceiling tile back into place. 8. Connect the Ethernet cable to the ETHERNET port. Wall Mounting ■ There are two wall-mounting slots on the back of the mounting bracket. To mount the EAP on a wall, please follow the steps below.
- Page 13 Attach the EAP to the mounting bracket by aligning ARROW 1 with ARROW 2. ARROW 1 ARROW 2 5. Turn the EAP clockwise until it locks into place. 6. Hang the EAP on the screws. Make sure the EAP is firmly seated against the wall.
-
Page 14: Power Supply
Switch (Up to 100m) Connect the ETHERNET port of EAP110 to the POE port of the PoE adapter through an Ethernet cable. The cable length can be up to 100 meters. 2. Connect the Ethernet cable from the switch to the LAN port of the PoE adapter. - Page 15 EAP120/EAP220 ■ EAP120/EAP220 can be powered via a PSE device (such as a PoE switch) or a power adapter. Via PoE Switch PoE Switch EAP120/EAP220 Connect the Ethernet cable from the PoE switch to the ETHERNET port of EAP120/EAP220. 2. Press the ON/OFF button on the interface panel of EAP120/EAP220. Via Power Adapter Socket Switch...
-
Page 16: Software Configuration
Controller Host. Note: The EAP Controller application file can be found on the resource CD or downloaded from our website http://www.tp-link.com/en. Refer to the EAP Controller User Guide to learn how to perform the installation. Step 2: Configuring the Controller Software Launch the EAP Controller and finish the configuration wizard to create a primary wireless network. -
Page 17: Q&A
Q&A Q1. What is the maximum cable length between the EAP110 and the provided PoE adapter? 100 meters. The quality of the Ethernet cable may influence the reception of the power supply. Q2. Could the EAP work as a standalone device if it had been adopted by the EAP Controller? No. -
Page 18: Specifications
Specifications HARDWARE FEATURES Model EAP110 EAP120 EAP220 Interface Kensington lock slot RESET button ETHERNET: ETHERNET: 10/100/1000Mbps Ethernet port (RJ- 10/100Mbps Ethernet port (RJ- CONSOLE port (RJ-45) ON/OFF button Power connector (DC-2) Power Supply 24V/1A passive PoE PoE(802.3af-compliant, PoE (802.3af-compliant, adapter (included) 36-57VDC, 0.2A Max) - Page 20 Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD.