Advertisement
Quick Links
Advertisement
Related Manuals for Kogan Certa CT529IN1GCKA
Summary of Contents for Kogan Certa CT529IN1GCKA
- Page 1 52CC 9-IN-1 LINE TRIMMER HEDGE TRIMMER CHAINSAW AND CUTTER CT529IN1GCKA...
-
Page 3: Safety And Warnings
SAFETY & WARNINGS • For safety reasons, minors are not allowed to work with the trimmer, except persons over 16 years of age who are trained under supervision. • Operate the trimmer in good physical and mental condition. Do not use the device in an ill or tired state or under the influence of any substances or medical preparations that may affect vision, physical or mental condition. - Page 4 • Perform tank refuelling outdoors on the ground. Close the fuel cap tightly. Do not refuel indoors. • Fuel is highly flammable and explosive. Do not smoke, do not allow the presence of sparks and flames in the fuel storage area and when the engine fuelling. Do not refuel a hot engine.
- Page 5 Transporting The device can be transported by any type of closed transport in the original packaging or without it, with the protection of the product from mechanical damage, precipitation, and exposure to chemically active substances. During loading and unloading operations, the device should not be exposed to shocks, falls and atmospheric precipitation.
- Page 6 OVERVIEW Starter handle Throttle trigger Starter Throttle lock Throttle valve control lever Throttle lever Plug cables Pipe and engine connection Fuel tank Coil with nylon thread Exhaust pipe Lower gearbox Grip Protective cover Engine casing 3T blade Chainsaw Double shoulder belt Lower handle attachment Mounting plate for the protective cover Shoulder strap ring...
- Page 7 Chainsaw Tire 5 Gear housing Chain 6 Bar cover Oil tank 7 Rod Oil cap...
- Page 8 Hedge cutter Blade covers Handle Blades Latch lock Gear housing...
-
Page 9: Installation
INSTALLATION Handle installation Place the device on a flat, hard, and clean surface. Unscrew the mounting collar using a wrench. Place the handle over the bar and secure it with the mounting clamp (Fig. 2). Tighten the screws. Screws Fig. 2 Install the shoulder strap by inserting the hook into the clip (Fig. - Page 10 Install the protective cover on the bar, inserting it between the bracket and the housing as shown below and fix it with four screws (Fig. 4). Fig. 4 Connect top and bottom so that the bottom spring button fits into the hole in the top bar.
- Page 11 Trimmer coil installation Align the holes in the gearbox cup with those on the flange washer. Insert the metal locking pin or hex key from the delivery set into the holes of the gearbox cup and the flange washer. Rotating the nut clockwise, remove it, as well as the cup and washer from the gear spindle (Fig.
- Page 12 WARNING: If the cutting blade is not aligned correctly, strong vibrations may occur during operation and the blade may come loose, causing injury to the operator or any third party. Place the brush cutter on a flat, stable surface with the engine off on the fuel tank cap. Make sure the brush cutter cover is in place.
- Page 13 Fig. 10 Adjusting lever Different cutting angles WARNING: Do not touch the blades while the engine is running. Blade movement is possible even when idle. The cutting blade can be adjusted on 12 positions from 120° to 270° (Fig. 11). Always check the latch lock after each adjustment.
- Page 14 ASSEMBLY Head installation To install the head, connect the upper and lower parts of the rod by turning it so that the spring button of the lower part fits into the hole of the coupling of the upper part of the rod. If necessary, rotate the spool shaft so that the drive shaft located in the lower part of the rod engages with the accompanying slot in the upper part.
- Page 15 Gear housing nut Gear housing Fig. 13 Tire adjustment stud Chain tension screw Chain tensioner Tire Chain tensioner hole Tire adjustment stud Fig. 14 Top loop Bottom loop Fig. 15...
- Page 16 Chain tension adjustment WARNING: Always wear protective gloves when working with the chain. The correct chain tension is extremely important, and it must be checked both before starting work and periodically during operation. Take the time to adjust the chain, as this will increase the performance of the saw and extend its service life.
- Page 17 Refilling the oil tank: Be sure to clean the surface around the oil tank cap for not getting dirt inside. Unscrew the oil tank cap and fill the chainsaw oil (tank capacity 200ml). Screw on the oil tank cap. Before start working, check the oil supply: turn on the pruning shears and hold them over a control place.
- Page 18 Brush cutter installation Make sure that the cutting insert is locked in the storage/transport position (tilted back) and that the guard is mounted on the cutting inserts. Connect the upper and lower part of the rod by turning it so that the spring button of the lower part fits into the hole of the coupling in the upper part of the rod.
-
Page 19: Operation
OPERATION Fuel mixture preparation For the preparation of the fuel mixture, petrol with an octane rating of no less than 92, and special oil for two-stroke air-cooled engines shall be used. The recommended proportional ratio of the petrol and fuel oil is 40:1, unless otherwise indicated on the label of the oil used. Never use oil designed for 2-stroke water-cooled engines (boat motors). - Page 20 Cold start WARNING: Before starting the engine, make sure that the working part of the trimmer does not touch foreign objects. WARNING: Hold the trimmer firmly so as not to lose control during starting. Do not run the trimmer in the air or with a belt. If you lose control, the device may strike your leg or an obstacle.
- Page 21 Press the primer located between the air filter and the fuel tank five or seven times to fill the carburettor with the fuel mixture, (Fig. 8). In this case, the pumped fuel mixture should be seen through the transparent button cap. If the fuel mixture does not fill the cap, press the primer several more times.
- Page 22 Turn the ignition switch, located on the control handle, to the on/1 position. Pressing the fuse lever, push the throttle lever (throttle lever) and lock it in the depressed state using the lock (Fig. 10). Gas throttle Switch lock Gas throttle Gas throttle trigger lever...
- Page 23 10. Warm up the engine for 30-60 seconds and start work. If the engine does not start, it is possible that you missed the first flash and the spark plug was flooded with fuel. In this case, you must perform the following steps: •...
- Page 24 Work rules WARNING: All trimmer work should be done in full gas mode. Do not use a trimmer without a properly installed guard. During operation, monitor the health and sharpness of the cord trimming blade. With the cover removed or defective, you will not be able to control the length of the trimmer reel cord or the load on the motor and driveshaft.
- Page 25 Trimming With this type of work, the grass is selectively mowed in a small area by moving the trimmer in a straight line. Move the trimmer carefully to the place to be cut (Fig. 12 a). Tilt the head a little to the side so that the waste does not fly in your direction.
- Page 26 Trimmer coil use The trimmer should move parallel to the ground. When mowing high and/or soft vegetation, make sure that the mowed grass does not wind on the trimmer reel axle. This complicates the rotation of the drive shaft and increases the load on the engine. Grass spooled on the axle can lead to heating and melting of the coil, breakage of the driveshaft, overheating of the engine and its failure.
- Page 27 Replacing the coil cord Do not use a cord with a diameter greater than recommended. Increasing the diameter of the fishing line leads to an overload of the engine and a reduction in the quality of mowing. To replace the cord, follow these steps: •...
- Page 28 Cutting blade The trimmer is equipped with a 3-blade metal cutter. A metal blade is used to mow thick grass or weeds. To prevent kickback and destruction of the blade, do not use it to cut bushes or young trees. It is not recommended to work with the metal blade if the site has large irregularities, a bumpy surface, deep pits, or ditches, or near trees, shrubs, and hedges.
-
Page 29: Cleaning And Care
CLEANING & CARE WARNING: All maintenance work on the trimmer, except for the items listed in these maintenance and operating instructions, must be performed by an authorised service centre. Maintenance dates are for normal use only. Under extreme operating conditions (heavy dust, heavy loads) or longer daily work, the specified intervals should be reduced. - Page 30 Types of maintenance work Visual control Complete device Cleaning Control levers Function control Sharpening control Cord cutter Sharpening Control Fuel filter Replacement Fuel tank Cleaning Gearbox Grease Every 20 working hours/at least once per season Inspection Trimmer head Replacement Landing control Cleaning Air filter Replacement...
- Page 31 Exhaust pipe Periodically inspect the spark arrester of the engine, which is a metal grid located in the outlet of the muffler. A contaminated spark arrestor can adversely affect engine performance and mowing quality. If contamination is detected, clean the spark arrester with a brush.
- Page 32 Fill the spark plug hole with 3-5ml of clean engine oil for two-stroke air-cooled engines. Slowly pull the starter cord several times so that the inner surfaces of the cylinder and piston are covered with oil. Install the piston in the upper position (pull the starter cord, keeping track of the position of the piston through the spark plug hole).
-
Page 33: Specifications
SPECIFICATIONS Specification Value Engine type 2-stroke, air cooled Engine displacement, cm3 Engine power, hp. Nylon thread mowing width, mm Nylon thread diameter, mm Disc mowing width, mm Fuel tank capacity, 1 Noise level, dB Trimmer weight without fuel, kg Chainsaw guide bar length, mm Hedge cutter length, mm Chainsaw Chainsaw, mm... -
Page 34: Troubleshooting
TROUBLESHOOTING Malfunction Possible reason Remedy The ignition switch is in the "off" Turn the ignition switch to the "on" position. position. Pour fresh fuel mixture into the fuel Empty fuel tank or airlock in the tank, bleed the fuel line with the fuel line. - Page 35 IN THE BOX Engine assembly with rod Grip Protective cover assembly with apron Coil with nylon thread 3T-Blade Double shoulder belt Fuel tank Fastener kit and tool kit User guide Chainsaw Hedge cutter Trimmer spool...
- Page 36 Need more information? We hope that this user guide has given you the assistance needed for a simple set-up. For the most up-to-date guide for your product, as well as any additional assistance you may require, head online to help.kogan.com...