Page 2
Please contact your local recycling authority for disposal of this product. Customer Support Customer technical support and services are provided by AudioCodes or by an authorized AudioCodes Service Partner. For more information on how to buy technical support for AudioCodes products and for contact information, please visit our website at https://www.audiocodes.com/services-support/maintenance-and-support...
Content Mediant 800 SBC | SNMP Reference Guide Table of Contents 1 Introduction 2 SNMP Overview SNMP Standards and Objects SNMP Message Standard SNMP MIB Objects SNMP Extensibility Feature Supported MIBs SNMP Interface Details SNMP Community Names Configuring Community Strings via the Web...
Page 7
Content Mediant 800 SBC | SNMP Reference Guide Performance Monitoring MIBs for SIP Messages Performance Monitoring MIBs for Calls per IP Group Performance Monitoring MIBs for Gateway Application IP-to-Tel and Tel-to-IP Calls Trunks Trunk Groups Performance Monitoring MIBs for SBC Application...
AudioCodes One Voice Operations Center (OVOC). OVOC is not included in the device's supplied package. Contact AudioCodes for more information on its OVOC solution for large VoIP deployments.
Simple Network Management Protocol (SNMP) is a standards-based network control protocol for managing elements in a network. The SNMP Manager, usually implemented by a third- party Network Management System (NMS) or AudioCodes One Voice Operations Center (OVOC), connects to an SNMP Agent (embedded on a remote Network Element (NE) to perform network element Operation, Administration, Maintenance, and Provisioning (OAMP).
CHAPTER 2 SNMP Overview Mediant 800 SBC | SNMP Reference Guide be determined via SNMP without the overhead associated with logging into the device, or establishing a TCP connection with the device. ■ Get Next Request: Enables the SNMP standard network managers to "walk" through all SNMP values of a device (via the "get-next"...
CHAPTER 2 SNMP Overview Mediant 800 SBC | SNMP Reference Guide ■ Table MIB Objects: Contain multiple pieces of management data. These objects are distinguished from "Discrete" items (above) by requiring a "." (dot) extension to their names that uniquely distinguishes the particular value being referenced. The "." (dot) extension is the "instance"...
Page 14
CHAPTER 2 SNMP Overview Mediant 800 SBC | SNMP Reference Guide ■ System MIB (under MIB-2): Standard system group: sysDescr, sysObjectID, sysUpTime, sysContact, sysName, sysLocation, and sysServices. You can replace the value of sysObjectID.0 with a variable value using the ini file parameter SNMPSysOid. This parameter is polled during startup and overwrites the standard sysObjectID.
Page 15
CHAPTER 2 SNMP Overview Mediant 800 SBC | SNMP Reference Guide All other objects in this table support GET only. ● dsx1CurrentTable ● dsx1IntervalTable ● dsx1TotalTable ● dsx1LineStatusChange trap ■ acPSTN MIB: ● acSonetSDHTable: currently has one entry (acSonetSDHFbrGrpMappingType) for selecting a low path mapping type. Relevant only for PSTN applications. (Refer to the MIB for more details.)
Page 16
CHAPTER 2 SNMP Overview Mediant 800 SBC | SNMP Reference Guide ● Secondary DNS Server IP Address - IP address of secondary DNS server for this interface ■ acSysModuleTable ■ acPSTN MIB ■ acGateway MIB: This proprietary MIB contains objects related to configuration of the SIP device.
SNMP Interface Details This subsection describes details of the SNMP interface needed when developing an Element Management System (EMS) for any AudioCodes devices, or to manage a device with a MIB browser. There are several alternatives for SNMP security: ■...
CHAPTER 2 SNMP Overview Mediant 800 SBC | SNMP Reference Guide Configuring Community Strings via the Web For detailed information on configuring community strings through the Web interface, refer to the device's User's Manual . Configuring Community Strings via the ini File The following ini file parameters are used to configure community strings: ■...
CHAPTER 2 SNMP Overview Mediant 800 SBC | SNMP Reference Guide ➢ To delete the read-write v2admin community string: If v2admin is being used as the trap community string, follow the procedure for changing the trap community string. (See below.) Delete the snmpCommunityTable row with a CommunityName of v2admin and GroupName of ReadWriteGroup.
CHAPTER 2 SNMP Overview Mediant 800 SBC | SNMP Reference Guide Security Levels Authentication Privacy authPriv(3) MD5 or SHA-1 DES, 3DES, AES128, AES192, or AES256 Each SNMPv3 user must be associated with one of the predefined groups listed in the following...
Page 21
CHAPTER 2 SNMP Overview Mediant 800 SBC | SNMP Reference Guide Parameter Description Default SNMPUsers_ Authentication protocol to be used for this user. AuthProtocol Possible values are 0 (none), 1 (MD5), 2 (SHA-1) SNMPUsers_ Privacy protocol to be used for this user. Possible...
CHAPTER 2 SNMP Overview Mediant 800 SBC | SNMP Reference Guide ■ The user v3admin2 is setup for a security level of authPriv(3), with authentication protocol SHA-1 and privacy protocol DES. The authentication text password is “myauthkey”, the privacy text password is “myprivkey”, and the user is associated with ReadWriteGroup3.
CHAPTER 2 SNMP Overview Mediant 800 SBC | SNMP Reference Guide Delete the vacmSecurityToGroupTable row for SecurityName v3admin1, GroupName ReadWriteGroup1 and SecurityModel usm. Delete the row in the usmUserTable for v3admin1. Trusted Managers By default, the SNMP agent accepts Get and Set requests from any IP address, as long as the correct community string is used in the request.
Page 24
CHAPTER 2 SNMP Overview Mediant 800 SBC | SNMP Reference Guide Add a row to the snmpTargetAddrExtTable table with these values: Name=mgr0, snm- pTargetAddrTMask=255.255.255.255:0. The agent does not allow creation of a row in this table unless a corresponding row exists in the snmpTargetAddrTable.
CHAPTER 2 SNMP Overview Mediant 800 SBC | SNMP Reference Guide SNMP Ports The SNMP Request Port is 161 and the SNMP Trap Port is 162. These port numbers for SNMP requests and responses can be changed, by using the [SNMPPort] ini file parameter. The valid value is any valid UDP port number.
Page 26
CHAPTER 2 SNMP Overview Mediant 800 SBC | SNMP Reference Guide ■ SNMPManagerTrapUser_<x>: indicates to send an SNMPv2 trap using the trap user community string configured with the SNMPTrapCommunityString parameter. You may instead specify an SNMPv3 user name. The following is an example of entries in the ini file regarding SNMP. The device can be configured to send to multiple trap destinations.
CHAPTER 2 SNMP Overview Mediant 800 SBC | SNMP Reference Guide ;SNMPManagerTrapSendingEnable_4=1 ;SNMPManagerTrapUser_4=’’ The ‘trap manager host name’ is configured via SNMPTrapManagerHostName. For example: ;SNMPTrapManagerHostName = 'myMananger.corp.MyCompany.com' The same information that is configurable in the ini file can also be configured via the acBoardMIB.
Page 28
CHAPTER 2 SNMP Overview Mediant 800 SBC | SNMP Reference Guide name of the SNMPv3 that this user is associated with. If a row does not already exist for this combination of user and SecurityLevel, add a row to the snmpTargetParamsTable with these values: Name=usm<user>, MPModel=3(SNMPv3), SecurityModel=3 (usm), SecurityName=<user>, SecurityLevel=M, where M is either 1...
CHAPTER 3 Carrier-Grade Alarm System Mediant 800 SBC | SNMP Reference Guide Carrier-Grade Alarm System The basic alarm system has been extended to a carrier-grade alarm system. A carrier-grade alarm system provides a reliable alarm reporting mechanism that takes into account EMS outages, network outages, and transport mechanism such as SNMP over UDP.
CHAPTER 4 Topology MIB Objects Mediant 800 SBC | SNMP Reference Guide Topology MIB Objects This section describes the topology of the MIB objects. Physical Entity (RFC 2737) The following groups are supported: ■ entityPhysical group: Describes the physical entities managed by a single agent.
Page 31
CHAPTER 4 Topology MIB Objects Mediant 800 SBC | SNMP Reference Guide ifTable & ifXTable Value standard. Support for 'testing' is not required. ifOperStatus Up or Down corresponding to acAnalogFxsFxoType where Unknown is equal to Down. ifLastChange The value of sysUpTime at the time the interface entered its current operational state.
CHAPTER 4 Topology MIB Objects Mediant 800 SBC | SNMP Reference Guide ifTable & ifXTable Value ifHCInOctets 64-bit versions of counters. Required for ethernet-like ifHCOutOctets interfaces that are capable of operating at 20 Mb/s or faster, even if the interface is currently operating at less than 20 Mb/s.
Page 33
CHAPTER 4 Topology MIB Objects Mediant 800 SBC | SNMP Reference Guide ifTable Value process we need to refer the Admin-Status parameter. ifOperStatus Up or Down, according to the operation status. ifLastChange The value of sysUpTime at the time the interface entered its current operational state.
CHAPTER 5 File Management Mediant 800 SBC | SNMP Reference Guide File Management SNMP supports file download, upload, and removal. Downloading a File to the Device The file URL is set in the appropriate MIB object under the acSysHTTPClient subtree (refer to the subtree objects description for the URL form).
Page 35
CHAPTER 5 File Management Mediant 800 SBC | SNMP Reference Guide File upload using SNMP is supported only for ini files; file removal using SNMP is supported for all files except ini files. - 26 -...
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring Performance measurements (performance monitoring) are available for third- party performance monitoring systems through an SNMP interface. These can be polled at scheduled intervals by an external poller or utility in the management server or other off- board systems.
Page 37
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide ● Trunk activity ● Number of channels that are in/out of service and in maintenance ■ acPMSystem: General device monitoring: ● IP connection. ● Discarded UDP packets due to unknown port ●...
Page 38
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide ■ 2: Second last completed interval When the current interval (Interval 0) completes (reaches 15 minutes), Interval 2 is discarded, Interval 1 becomes Interval 2, Interval 0 becomes Interval 1, and a new Interval 0 is created.
Page 39
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide The performance monitoring MIB tables can include the following properties (columns): ■ Table specific index: This is a table key. ■ Interval: Indicates the measured interval (0,1, or 2), which is a table key.
Page 40
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide The SNMP trap event acPerformanceMonitoringThresholdCrossing is sent every time the Performance high or low threshold of a Performance Monitored MIB object is crossed (see Monitoring Threshold-Crossing Trap on page 162 ). The severity field is 'indeterminate' when the crossing is above the threshold and 'cleared' when it returns to below the threshold.
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide PM_gwIPGroupOutINVITEDialogs = '1,10,18,15' If you download (save) the device's ini file, it includes all SNMP performance monitoring MIBs whose thresholds (low and/or high) you have changed from default. To apply these same threshold values to other devices, load the file to the other devices.
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide The tables in this section use check marks "√" and crosses "x" to indicate support for the specific MIB property: ● "G/C": gauge / counter ● "Int": measured interval ●...
Page 43
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring MIB owThreshold (1.3.6.1.4.1.5003.10.11.1.33.2) ■ MIB Name: acPMNetUtilPacketsTable ■ OID: 1.3.6.1.4.1.5003.10.11.2.31.2 ■ Source Name: PM_NetUtilPackets ü ü ü ü ü ü ü ü ü Indicates the number of incoming and outgoing packets from the interface (Index 0 is transmit;...
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring MIB OVOC parameter name: Number of Incoming Discarded Pkts. Performance Monitoring MIBs for Media Realms The following table lists the performance monitoring MIBs for Media Realms. Table 6-2: Performance Monitoring MIBs for Media Realms Performance Monitoring MIB ■...
Page 45
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring MIB ■ Low threshold: acPMMediaRealmAttributesMediaR ealmBytesTxLowThreshold (1.3.6.1.4.1.5003.10.8.1.35.2) ■ MIB Name: acPMMediaRealmBytesRxTable ■ OID: 1.3.6.1.4.1.5003.10.8.2.53.2 ■ Source Name: PM_MediaRealmBytesRx Indicates the number of bytes received û ü ü ü ü ü ü...
Page 46
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring MIB ■ Source Name: PM_MediaRealmPacketsRx û ü ü ü ü ü ü Indicates the number of media packets received in RTCP data, per Media Realm. ■ High threshold:...
Page 47
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring MIB mPacketJitterHighThreshold (1.3.6.1.4.1.5003.10.8.1.35.11) ■ Low threshold: acPMMediaRealmAttributesVEReal mPacketJitterLowThreshold (1.3.6.1.4.1.5003.10.8.1.35.12) ■ MIB Name: acPMMediaRealmRealmMOSTable ■ OID: 1.3.6.1.4.1.5003.10.8.2.53.7 ■ Source Name: PM_RealmMOS ü ü ü ü û û û Indicates the MOS quality in RTCP-XR data, per Media Realm.
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring MIB ■ MIB Name: acPMMediaRealmBwTxTable ■ OID: 1.3.6.1.4.1.5003.10.8.2.53.9 ■ Source Name: PM_MediaRealmBwTx ü ü ü ü û û û Indicates the average bandwidth for Tx bytes, per Media Realm.
Page 49
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring MIB (Speex). ■ High threshold: acPMCodersAttributesChannelsPerCod erHighThreshold (1.3.6.1.4.1.5003.10.7.1.32.1) ■ Low threshold: acPMCodersAttributesChannelsPerCod erLowThreshold (1.3.6.1.4.1.5003.10.7.1.32.2) ■ MIB Name: acPMChannelsPerCoderG711Table ■ OID: 1.3.6.1.4.1.5003.10.7.2.26 ■ Source Name: PM_VeG711Channels Indicates the number of active channels ü...
Page 50
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring MIB acPMNetworkingAttributesModuleRTP PacketLossRxHighThreshold (1.3.6.1.4.1.5003.10.7.1.33.17) ■ Low threshold: acPMNetworkingAttributesModuleRTP PacketLossRxLowThreshold (1.3.6.1.4.1.5003.10.7.1.33.18) ■ MIB Name: acPMModuleRTPPacketLossTxTable ■ OID: 1.3.6.1.4.1.5003.10.7.2.31.10 ■ Source Name: PM_veModuleRTPPacketLossTx ü ü ü ü ü ü ü ü ü...
Page 51
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring MIB ■ Low threshold: acPMNetworkingAttributesPacketDelay LowThreshold (1.3.6.1.4.1.5003.10.7.1.33.2) ■ MIB Name: acPMModulePacketJitterTable ■ OID: 1.3.6.1.4.1.5003.10.7.2.31.21.2 ■ Source Name: PM_veModulePacketJitter Indicates the RTP packet jitter during the ü ü ü ü...
Page 52
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring MIB ■ MIB Name: acPMModuleRTPBytesTxTable ■ OID: 1.3.6.1.4.1.5003.10.7.2.31.21.3 ■ Source Name: PM_veModuleRTPBytesTx ü ü ü ü ü ü ü ü ü Indicates the Rx RTP bytes during the collection time interval.
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring MIB ü ü ü ü ü ü ü ü ü Indicates the Tx RTP Packets during the collection time interval. OVOC parameter name: Tx RTP Packets. ■ High threshold:...
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring MIB nsPerSecondLowThreshold (1.3.6.1.4.1.5003.10.8.1.34.36) ■ MIB Name: acPMSIPIPGroupInviteDialogsTable ■ OID: 1.3.6.1.4.1.5003.10.8.2.52.22 ■ Source Name: PM_gwIPGroupINVITEDialogs ü ü ü ü ü ü ü Indicates the number of INVITE dialogs per IP Group.
Page 55
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring TbLT TaHT number of attempted incoming calls per IP Group. ■ MIB Name: acPMSBCIPGroupOutAttemptedCallsTable ■ OID: 1.3.6.1.4.1.5003.10.8.2.54.6 ■ Source Name: PM_gwSBCIPGroupOutAttemptedCalls Indicates the ü û û û û...
Page 56
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring TbLT TaHT ■ OID: 1.3.6.1.4.1.5003.10.8.2.54.19 ■ Source Name: PM_gwSBCIPGroupOutNoResourcesCalls ü û û û û û û û û Indicates the number of outgoing call resource allocation failures per IP Group.
Page 57
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring TbLT TaHT Indicates the ü û û û û û û û û number of incoming busy calls per IP Group. ■ MIB Name: acPMSBCIPGroupOutBusyCallsTable ■ OID: 1.3.6.1.4.1.5003.10.8.2.54.23 ■...
Page 58
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring TbLT TaHT ■ MIB Name: acPMSBCIPGroupInForwardedCallsTable ■ OID: 1.3.6.1.4.1.5003.10.8.2.54.26 ■ Source Name: PM_gwSBCIPGroupInForwardedCalls ü û û û û û û û û Indicates the number of incoming forwarded calls per IP Group.
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring TbLT TaHT Indicates the ü û û û û û û û û number of outgoing calls that failed due to general fail reason per IP Group. ■...
Page 60
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide In the MIB tables, Index 0 indicates Tel-to-IP calls and Index 1 indicates IP-to-Tel calls. Table 6-6: Performance Monitoring MIBs for IP-to-Tel and Tel-to-IP Calls Performance Monitoring MIB ■ MIB Name: acPMSIPAttemptedCallsTable ■...
Page 62
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring MIB OVOC parameter name: IP to Tel / Tel to IP Number of Calls Terminated due to No Answer. ■ MIB Name: acPMSIPNoRouteCallsTable ■ OID: 1.3.6.1.4.1.5003.10.8.2.52.6 ■ Source Name: PM_gwNoRouteCalls ü...
Page 63
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring MIB ■ Source Name: PM_gwFaxAttemptedCalls ü û û û û û û û û Indicates the number of attempted fax calls. ■ MIB Name: acPMSIPFaxSuccessCallsTable ■ OID: 1.3.6.1.4.1.5003.10.8.2.52.10 ■...
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring MIB Indicates the current number of ü û û û û û û û û established calls pertaining to a trunk for Tel-to-IP calls. ■ MIB Name: acPMSIPIP2TelTrunkEstablishedCallsTable ■...
Page 65
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring MIB ü û û û û û û û û The DS1 Interval Table contains various statistics collected by each DS1 Interface over the previous 24 hours. The past 24...
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring MIB encountered by a DS1 interface in the previous 24-hour interval (OVOC parameter name: Trunk Path Coding Violations) ■ dsx1TotalBESs: Number of Bursty Errored Seconds encountered by a DS1 interface...
Page 68
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring MIB per Trunk Group. ■ High threshold: acPMSipAttributesTrunkGroupNoReso urcesCallsHighThreshold (1.3.6.1.4.1.5003.10.8.1.34.7) ■ Low threshold: acPMSipAttributesTrunkGroupNoReso urcesCallsLowThreshold (1.3.6.1.4.1.5003.10.8.1.34.8) ■ MIB Name: acPMSIPTrunkGroupCallDurationTable ■ OID: 1.3.6.1.4.1.5003.10.8.2.52.29 ■ Source Name: PM_gwTrunkGroupCallDuration Indicates the average call duration (in ü...
Page 69
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring MIB acPMSipAttributesTrunkGroupUtilizati onHighThreshold (1.3.6.1.4.1.5003.10.8.1.34.3) ■ Low threshold: acPMSipAttributesTrunkGroupUtilizati onLowThreshold (1.3.6.1.4.1.5003.10.8.1.34.4) ■ MIB Name: acPMSIPTrunkGroupPercentageUtilizationTable ■ OID: 1.3.6.1.4.1.5003.10.8.2.52.27 ■ Source Name: PM_gwTrunkGroupPercentageUtilization ü ü ü ü ü ü ü...
Page 70
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring MIB concurrently busy, if this scenario occurs. For example, if trunk group #3 has 200 channels and all these were concurrently busy for 60 seconds, then this MIB will display 60 for this trunk group.
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring MIB ■ OID: 1.3.6.1.4.1.5003.10.10.2.21 ■ Source Name: PM_TrunkUtilization ü ü ü ü ü ü ü Indicates the number of busy channels on a specific E1 / T1 trunk. A busy channel is when the Physical DS0 Termination isn't in Null context or OOS.
Page 72
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring MIB legs per call. Therefore, each successful call increments the counter by 2. If the INVITE fails Classification stage, only the incoming side is counted (i.e., counter incremented only by 1).
Page 73
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring MIB (1.3.6.1.4.1.5003.10.8.1.34.39) ■ Low threshold: acPMSipAttributesSBCEstablished CallsLowThreshold (1.3.6.1.4.1.5003.10.8.1.34.40) ■ MIB Name: acPMSBCInEstablishedCallsTable ■ OID: 1.3.6.1.4.1.5003.10.8.2.54.69 ■ Source Name: PM_gwSBCInEstablishedCalls Indicates the total number of ü û û û...
Page 74
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring MIB ShortCallSeconds parameter. ■ MIB Name: acPMSBCOutShortCallsTable ■ OID: 1.3.6.1.4.1.5003.10.8.2.54.152.2 ■ Source Name: PM_gwSBCOutShortCalls ü û û û û û û û û Indicates the total number of...
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring MIB ■ MIB Name: acPMSBCMediaLegsTable ■ OID: 1.3.6.1.4.1.5003.10.8.2.54.47 ■ Source Name: PM_gwSBCMediaLegs ü ü ü ü ü ü ü Indicates the number of media (RTP) session resources currently utilized.
Page 76
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Table 6-10: Performance Monitoring MIBs for SBC Calls per IP Group Performance Monitoring MIB ■ MIB Name: acPMSBCIPGroupInCallEstablishedDurationTable ■ OID: 1.3.6.1.4.1.5003.10.8.2.54.1 ■ Source Name: PM_gwSBCIPGroupInCallEstablishedDuration Indicates the call ü û...
Page 77
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring MIB ■ OID: 1.3.6.1.4.1.5003.10.8.2.54.7 ■ Source Name: PM_gwSBCIPGroupOutAttemptedSUBSCRIBEDialogs ü û û û û û û û û Indicates the number of attempted outgoing SUBSCRIBE dialogs per IP Group.
Page 78
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring MIB ü û û û û û û û û Indicates the number of failed incoming dialogs due to Admission Control rules per IP Group. ■ MIB Name: acPMSBCIPGroupInAdmissionFailedSubscribeDialogsTable ■...
Page 79
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring MIB ü û û û û û û û û Indicates the number of failed outgoing SUBSCRIBE dialogs pertaining to Admission Control per IP Group. ■ MIB Name: acPMSBCIPGroupOutAdmissionFailedOtherDialogsTable ■...
Page 80
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring MIB ü û û û û û û û û Indicates the number of outgoing forwarded SUBSCRIBE dialogs per IP Group. ■ MIB Name: acPMSBCIPGroupOutForwardedOtherDialogsTable ■ OID: 1.3.6.1.4.1.5003.10.8.2.54.31 ■...
Page 81
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring MIB ü û û û û û û û û Indicates the number of outgoing SUBSCRIBE dialogs that failed due to general fail reason per IP Group. ■...
Page 82
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring MIB ü û û û û û û û û Indicates the number of outgoing established SUBSCRIBE dialogs per IP Group. ■ MIB Name: acPMSBCIPGroupOutEstablishedOtherDialogsTable ■ OID: 1.3.6.1.4.1.5003.10.8.2.54.43 ■...
Page 83
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring MIB of established calls per IP Group that were disconnected because no RTP packets (media) were received for a user-defined period (configured by the BrokenConnectionEven tTimeout parameter). ■...
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring MIB user registrations per IP Group. ■ MIB Name: acPMSBCIPGroupOutAttemptedRegistrationsTable ■ OID: 1.3.6.1.4.1.5003.10.8.2.54.153.6 ■ Source Name: PM_gwSBCIPGroupOutAttemptedRegistrations ü û û û û û û û û Indicates the number...
Page 85
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring ■ Source Name: PM_gwSBCSRDInAttemptedCalls, Indicates the number of ü û û û û û û û û incoming attempted calls per SRD. ■ MIB Name: acPMSBCSRDOutAttemptedCallsTable ■ OID: 1.3.6.1.4.1.5003.10.8.2.54.68 ■...
Page 86
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring (configured by the BrokenConnectionEventT imeout parameter). ■ MIB Name: acPMSBCSRDInShortCallsTable ■ OID: 1.3.6.1.4.1.5003.10.8.2.54.152.3 ■ Source Name: PM_gwSBCSRDInShortCalls ü û û û û û û û û Indicates the number of...
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring registrations per SRD. ■ MIB Name: acPMSBCSRDInSuccessfulRegistrationsTable ■ OID: 1.3.6.1.4.1.5003.10.8.2.54.154.3 ■ Source Name: PM_gwSBCSRDInSuccessfulRegistrations Indicates the number of ü û û û û û û û û incoming successful registrations per SRD.
Page 88
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring MIB ■ Source Name: PM_gwSRDDialogs ü û û û û û û û û Indicates the number of all dialogs currently being handled by the SBC per SRD.
Page 89
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring MIB IP Group. ■ MIB Name: acPMSIPIPGroupSubscribeDialogsTable ■ OID: 1.3.6.1.4.1.5003.10.8.2.52.23 ■ Source Name: PM_gwIPGroupSUBSCRIBEDialogs ü ü ü ü ü ü ü Indicates the number of all SUBSCRIBE dialogs (initiated by SIP:SUBSCRIBE) currently being handled by the SBC, per IP Group.
Page 90
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring MIB ■ MIB Name: acPMSIPIPGroupOutOtherDialogsTable ■ OID: 1.3.6.1.4.1.5003.10.8.2.52.37 ■ Source Name: PM_gwIPGroupOutOtherDialogs ü û û û û û û û û Indicates the number of all outgoing dialogs other than INVITE and...
Page 91
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring MIB acPMSipAttributesIPGroupInSubscrib eDialogsLowThreshold (1.3.6.1.4.1.5003.10.8.1.34.16) ■ MIB Name: acPMSIPIPGroupOutInviteDialogsTable ■ OID: 1.3.6.1.4.1.5003.10.8.2.52.35 ■ Source Name: PM_gwIPGroupOutINVITEDialogs ü ü ü ü ü ü ü Indicates the number of outgoing calls (SIP INVITE) per IP Group.
Page 92
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring MIB ■ Source Name: PM_gwIPGroupOutDialogs ü û û û û û û û Indicates the number of outgoing û dialogs per IP Group. ■ MIB Name: acPMSIPInvitedDialogsTable ■...
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring MIB ■ OID: 1.3.6.1.4.1.5003.10.8.2.54.46 ■ Source Name: PM_gwSBCRegisteredUsers ü ü ü ü ü ü ü Indicates the number of registered users. Increments for each registered user and decrements when they deregister.
Page 94
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance TbLT TaHT Monitoring MIB ■ OID: 1.3.6.1.4.1.5003.10.8.2.54.50 ■ Source Name: PM_gwSBCIPGroupASR ü ü ü ü û û û û û Indicates ASR per IP Group. ■ MIB Name: acPMSBCSrdAsrTable ■...
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance TbLT TaHT Monitoring MIB ■ OID: 1.3.6.1.4.1.5003.10.8.2.54.52 ■ Source Name: PM_gwSBCACD ü ü ü ü û û û û û Indicates the Average Call Duration (ACD) for all (global) entities (i.e., all IP...
Page 96
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Table 6-14: Performance Monitoring MIBs for SBC Calls Per Second Performance Monitoring TbLT TaHT ■ MIB Name: acPMSBCInCapsTable ■ OID: 1.3.6.1.4.1.5003.10.8.2.54.59 ■ Source Name: PM_gwSBCInCPS ü ü ü ü û...
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring TbLT TaHT of CPS for outgoing SBC calls per SRD. ■ MIB Name: acPMSBCIPGroupInCapsTable ■ OID: 1.3.6.1.4.1.5003.10.8.2.54.61 ■ Source Name: PM_gwSBCIPGroupInCPS ü ü ü ü û û û...
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Performance Monitoring MIB ■ Source Name: PM_HALinkRedundantToActivePacketLossPercentage ü ü ü ü ü ü ü ü Indicates packet loss (in %) on the HA Maintenance interface from Redundant to Active device, where 0% indicates no packet loss.
Page 99
CHAPTER 6 Performance Monitoring Mediant 800 SBC | SNMP Reference Guide Table 6-16: Performance Monitoring MIB for DSP Utilization Performance Monitoring MIB ■ MIB Name: acPMDSPUsageTable ■ OID: 1.3.6.1.4.1.5003.10.7.2.25 ■ Source Name: PM_VEDSPUsage ü ü ü ü ü ü ü ü...
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide SNMP Traps This section describes the SNMP traps supported by the device. Standard Traps The device also supports the following standard traps: ■ authenticationFailure ■ coldStart: The device supports a cold start trap to indicate that the device is starting up.
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Trap Varbinds Trap varbinds are sent with each proprietary SNMP trap. Refer to the AcBoard MIB for more information on these varbinds. Table 7-1: Trap Varbinds for Proprietary SNMP Traps...
Page 105
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Trap Varbind Description characters. acBoardTrapGlobalsAdditionalInfo2 (9) Provides additional information regarding the reported trap. The value is an octet string of up to 100 characters. acBoardTrapGlobalsAdditionalInfo3 (10) Provides additional information regarding the reported trap.
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Trap Varbind Description Note: The device sends an empty string "\0". AudioCodes OVOC provides the proper string value when it sends it northbound. acBoardTrapGlobalsSystemSerialNumber The Serial Number of the device that sent the (16) trap.
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acTrunksAlarmNearEndLOS Check that the correct cable type is being used (crossed/straight). Contact AudioCodes Support. Cleared End of LOS Trunk Near-End LOF Alarm Table 7-4: acTrunksAlarmNearEndLOF Alarm acTrunksAlarmNearEndLOF 1.3.6.1.4.1.5003.9.10.1.21.2.0.50 Default...
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acTrunksAlarmNearEndLOF Cleared End of LOF Trunk AIS Alarm Table 7-5: acTrunksAlarmRcvAIS Alarm acTrunksAlarmRcvAIS 1.3.6.1.4.1.5003.9.10.1.21.2.0.51 Source Interfaces#0/Trunk#<m>, where m is the trunk interface number, 1 being Varbind the first trunk...
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Probable transmitFailure Cause Severity Condition Text Corrective Action Critical "Trunk RAI Alarm" Make sure that transmission is correct. Cleared End of RAI DS1 Line Status Alarm The alarm is applicable only to digital PSTN interfaces.
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm dsx1LineStatusChange 1 dsx1NoAlarm No alarm present 2 dsx1RcvFarEndLOF Far end LOF (a.k.a., Yellow Alarm) 4 dsx1XmtFarEndLOF Near end sending LOF Indication 8 dsx1RcvAIS Far end sending AIS 16 dsx1XmtAIS Near end sending AIS 32 dsx1LossOfFrame Near end LOF (a.k.a., Red Alarm) 64 dsx1LossOfSignal Near end Loss Of Signal...
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acBChannelAlarm Type Probable degradedSignal Cause Alarm Condition Text Corrective Action Severity Major B-channel service state changes to "B-Channel Corrective action 'Out of Service' or 'Maintenance' Alarm. %s" is not necessary...
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acDChannelStatus Alarm. D- Channel is Out Of Service" Minor NFAS D-channel (primary or backup) goes down "D- (fails) Channel Alarm. Primary NFAS D- Channel is Out Of Service" "D- Channel Alarm.
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acNFASGroupAlarm Severity Condition Text Corrective Action ■ Major An NFAS "NFAS Group The alarm is sent only group goes Alarm. %s" when the backup Non- out-of- Facility Associated service Signaling (NFAS) D-channel also falls, i.e., when both...
Page 115
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acHASystemFaultAlarm Critical HA feature has "SYS_HA: HA Need to configure a valid failed to initialize Remote address 'HA Remote Address'. due to some not configured, configuration No HA system."...
Page 117
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acHASystemFaultAlarm "Switch-Over: HA was lost due to Reason = switchover due to the HA Network Network Monitor feature as Monitor error. the threshold of Failed table rows unreachable rows (in the HA index: <id 1>...
Page 118
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acHASystemFaultAlarm Reason = Fk switchover caused by a upgrade" Hitless License Upgrade process and should return automatically after a few minutes. Corrective action is not required. “Switch-Over: HA was lost due to...
Page 119
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acHASystemFaultAlarm Minor HA Network "Network Monitor feature Monitor switch- will not be the over is blocked cause of a when HA switchover as the Preemptive 'Preempt Mode' mode and...
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide HA System Configuration Mismatch Alarm Table 7-12: acHASystemConfigMismatchAlarm Alarm acHASystemConfigMismatchAlarm 1.3.6.1.4.1.5003.9.10.1.21.2.0.34 Description The alarm is sent when the configuration of the modules in the High Availability (HA) system is not identical, causing instability.
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide HA System Switch Over Alarm Table 7-13: acHASystemSwitchOverAlarm Alarm acHASystemSwitchOverAlarm 1.3.6.1.4.1.5003.9.10.1.21.2.0.35 Description The alarm is sent when a switchover occurs from active to redundant device in a High Availability (HA) system.
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acHASystemSwitchOverAlarm switchover HA Network Monitor Alarm Table 7-14: acHANetworkMonitorAlarm Alarm acHANetworkMonitorAlarm 1.3.6.1.4.1.5003.9.10.1.21.2.0.136 Description The alarm is sent when all previously reachable destinations configured for a specific row in the HA Network Monitor table (for the HA Network Monitor feature) are now unreachable (i.e., none of them reply to the...
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide HA Ethernet Group Alarm Table 7-15: acHAEthernetGroupAlarm Alarm acHAEthernetGroupAlarm 1.3.6.1.4.1.5003.9.10.1.21.2.0.137 Description The alarm is sent when the Ethernet link of at least one port in the Ethernet Group that is associated with the HA Maintenance interface is down.
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acBoardConfigurationError Critical A configuration "Board Config Check the run- error was Error: A run-time time specific detected specific string string to determ- describing the ine the nature of configuration the configuration error"...
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acBoardEvResettingBoard Web interface or required. SNMP The alarm remains at Critical severity level until the device completes the reboot. A Clear trap is not sent. Software Upgrade Alarm Table 7-19: acSWUpgradeAlarm...
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acBoardCallResourcesAlarm Default Major Severity Event Type processingErrorAlarm Probable softwareError (46) Cause Severity Condition Text Corrective Action Major Percentage of busy channels "Call resources Do one of the exceeds the predefined RAI alarm"...
Page 128
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acProxyConnectionLost Severity Condition Text Corrective Action Major Connection to all the proxy "Proxy Set Ping the proxy servers in the Proxy Set are <ID>: Proxy server. If there is no lost (offline) and the 'Proxy lost.
Page 129
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acProxyConnectionLost Major Connection to the Proxy Set "Proxy Set <ID>: Ping the proxy is lost and this Proxy Set is Proxy not server. If there is no configured with fallback to found.
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acProxyConnectionLost the proxy set are offline" All proxy servers were offline "Proxy Set <ID> and now at least one proxy ("<Name>"): server in the Proxy Set is Server <IP online (and at least one address>:<port>...
Page 131
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acBoardControllerFailureAlarm Default Major Severity Event Type processingErrorAlarm Probable softwareError (46) Cause Severity Condition Text Additional Information Major Failure in a Proxy Set "Proxy Set ID n" Where n represents the Proxy Set ID.
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acBoardControllerFailureAlarm Failure in a Serving IP "BusyOut Trunk n Group for the trunk Serving IP Group Failure" Where n represents the BRI / PRI trunk ID. FXO physical port is "BusyOut Line n Link...
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acBoardOverloadAlarm Probable softwareError (46) Cause Severity Condition Text Corrective Action Major An overload "System CPU overload Make sure that condition exists in condition - the syslog level one or more of the...
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acgwAdminStateChange ■ changed Gateway is shutting down. A network administrator No time limit." took an action to shutting gracefully lock the device. down ■ Major Admin "Locked" No corrective action is state required.
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acOperationalStateChange state of the node is disabled if the device fails to properly initialize. ■ Look for other alarms and Syslogs that might provide additional information about the error.
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acRemoteMonitoringAlarm successful response (2xx) when it sends the monitoring report. TLS Certificate Expiry Alarm Table 7-27: acCertificateExpiryAlarm Alarm acCertificateExpiryAlarm 1.3.6.1.4.1.5003.9.10.1.21.2.0.128 Description The alarm is sent to indicate that the installed TLS certificate belonging to a configured TLS Context is about to expire (which cannot be renewed automatically) or has expired.
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acCertificateExpiryAlarm certificate of TLS context %d will expire in a day" "The TLS certificate of TLS context %d will expire in less than a day" Critical The certificate has expired.
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acFeatureKeyError Event Type processingErrorAlarm Probable Cause configurationOrCustomizationError (7) Alarm Severity Condition Text Corrective Action Critical License Key "Feature key error. error" License Key Hitless Upgrade Alarm The alarm is applicable only to the local License Key.
Page 139
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Table 7-30: acLicensePoolApplicationAlarm Alarm acLicensePoolApplicationAlarm 1.3.6.1.4.1.5003.9.10.1.21.2.0.107 Description The alarm is sent when the device receives new SBC licenses from the OVOC License Pool and any of the following conditions exist: ■...
Page 140
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acLicensePoolApplicationAlarm but it is not Pool. If yes, listed in the then add it to License Pool. the OVOC License Pool. If not, then remove the device from the License Pool.
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acLicensePoolApplicationAlarm ■ HA: The License Key device or reset the receives a device. new SBC License from the License Pool Manager, but the devices are currently undergoing a local License Key upgrade.
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acLicensePoolOverAllocationAlarm supported by the capability and will upgrade); the device sets device. not be applied” its SBC capacity to maximum and disregards (Sent after the the excess configured configuration has sessions.
Page 143
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acLicensePoolInfraAlarm Text Event Type communicationsAlarm Probable Cause keyExpired Alarm Severity Condition Text Corrective Action Critical Device unable to establish "License Pool In OVOC, perform an HTTPS REST connection Alarm. License...
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acLicensePoolInfraAlarm reset or hitless upgrade. Clear The alarm is cleared when: ■ Connection has been re-established with the OVOC License Pool. An updated license has been loaded to the...
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acFlexLicenseManagerAlarm Probable Cause communicationsProtocolError Corrective Alarm Severity Condition Text Action Warning OVOC Flex License pool "Service for <service stops the device’s name> license service of an SBC parameter is stopped"...
Page 146
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acCloudLicenseManagerAlarm Text Event Type processingErrorAlarm Probable configurationOrCustomisationError Cause Severity Condition Text Corrective Action ■ Major There is no connection "No Check TCP/TLS between the device and connection connectivity. OVOC either prior to initial with OVOC"...
Page 147
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acCloudLicenseManagerAlarm in the Retry-After header if specified, or immediately following an update of the OVOC Product Key. ■ OVOC response to Register requests: ■ 200: If successful request ■...
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acFloatingLicenseAlarm Probable Cause communicationsProtocolError Corrective Severity Condition Text Action Warning An attempt was made to "Not enough Configure an configure a customized memory to Allocation Allocation Profile with values...
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acNTPServerStatusAlarm Protocol (NTP) server. its IP address is configured incorrectly in the device). Minor No communication to NTP server after the time was already set once. Ethernet Link Alarm...
Page 151
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acBoardEthernetLinkAlarm device’s Ethernet link LEDs to determ- ine which interface Minor Ethernet Group "No Ethernet link" is failing. with two Ethernet ports and both are Reconnect down, or Ethernet...
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acBoardEthernetLinkAlarm the no HA alarm that follows such a case. Ethernet Group Alarm Table 7-38: acEthernetGroupAlarm Alarm acEthernetGroupAlarm 1.3.6.1.4.1.5003.9.10.1.21.2.0.86 Description The alarm is sent when an Ethernet port in an Ethernet Group goes down.
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acEthernetGroupAlarm up again. LDAP Lost Connection Alarm Table 7-39: acLDAPLostConnection Alarm acLDAPLostConnection 1.3.6.1.4.1.5003.9.10.1.21.2.0.75 Default Severity Minor Event Type communicationsAlarm Probable Cause communicationsSubsystemFailure If a connection is idle for more than the maximum configured...
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide IPv6 Error Alarm Table 7-41: acIPv6ErrorAlarm Alarm acIPv6ErrorAlarm 1.3.6.1.4.1.5003.9.10.1.21.2.0.53 Default Critical Severity Source System#0/Interfaces#<n>. Varbind Text Event operationalViolation Type Probable communicationsProtocolError Cause Corrective Severity Condition Text Action ■ Critical Bad IPv6 "IP interface alarm: IPv6 configuration failed, IPv6...
Page 155
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide NGINX Configuration is Invalid Table 7-42: acNGINXConfigurationIsInvalidAlarm Alarm acNGINXConfigurationIsInvalidAlarm 1.3.6.1.4.1.5003.9.10.1.21.2.0.130 Description The alarm is sent when NGINX Directives Sets have been configured with invalid syntax. NGINX continues to run with the previous, valid...
Page 156
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide NGINX Process Not Running Table 7-43: acNGINXPprocessIsNotRunningAlarm Alarm acNGINXPprocessIsNotRunningAlarm 1.3.6.1.4.1.5003.9.10.1.21.2.0.131 Description The alarm is sent when the device is restarted with an erroneous NGINX configuration (i.e., after the alarm "NGINX Configuration is not Valid"...
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acHTTPProxyServiceAlarm Severity Condition Text Corrective Action Major When "HTTP Proxy Ping the host. If there is no connection Upstream ping, contact your provider. to the Host IP:Port The probable reason is that...
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acActiveAlarmTableOverflow Event Type processingErrorAlarm Probable resourceAtOrNearingCapacity (43) Cause Alarm Condition Text Corrective Action Severity ■ Major "Active Some alarm information may be lost but the many alarm ability of the device to perform its basic...
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acAnalogPortSPIOutOfService Text Event physicalViolation Type Probable equipmentMalfunction Cause Alarm Condition Text Corrective Action Severity ■ Major Analog port "Analog No corrective action is required. has gone Port SPI out ■...
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acAnalogPortHighTemperature automatically down the analog disconnected. port and tries to activate it again later when the device's temperature drops. Cleared Temperature is back to normal - analog port is back in service.
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Analog Line Left Off-hook Alarm The alarm is applicable only to FXS interfaces. Table 7-49: acAnalogLineLeftOffhookAlarm Alarm acAnalogLineLeftOffhookAlarm 1.3.6.1.4.1.5003.9.10.1.21.2.0.141 Description The alarm is sent when an analog FXS phone is left off-hook for a user- defined time, configured by the FXSOffhookTimeoutAlarm parameter.
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acMediaRealmBWThresholdAlarm Type Probable The alarm is sent when a bandwidth threshold is crossed Cause Severity Condition Text Corrective Action Major "Media Realm BW Cleared when bandwidth threshold Threshold Alarm"...
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acASRThresholdAlarm Minor ASR is equal or less than "ASR threshold the configured Minor crossed." threshold (but greater than the Major threshold). Cleared ASR is above the configured Minor threshold plus the hysteresis.
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acACDThresholdAlarm than the configured Minor threshold (but greater than the Major threshold). Cleared ACD is above the configured Minor threshold plus the hysteresis. Network Effectiveness Ratio Threshold Alarm Table 7-53: acNERThresholdAlarm...
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acNERThresholdAlarm than the Major threshold). Cleared NER is above the configured Minor threshold plus the hysteresis. No Route to IP Group Alarm Table 7-54: acIpGroupNoRouteAlarm Alarm acIpGroupNoRouteAlarm 1.3.6.1.4.1.5003.9.10.1.21.2.0.114 Description...
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Alarm acIpGroupNoRouteAlarm Alarm Text <Alarm Description Reason> as described above. Event Type Quality Of Service Alarm Probable Cause One of the reasons described above. Corrective Severity Condition Text Action Major When calls rejected to IP Group "IP Group is...
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Intrusion Detection System (IDS) This section describes the trap events concerned with the Intrusion Detection System (IDS) feature. IDS Threshold Cross Notification Trap Table 7-56: acIDSThresholdCrossNotification Event acIDSThresholdCrossNotification 1.3.6.1.4.1.5003.9.10.1.21.2.0.100 Description The alarm is sent for each scope (IP or IP+Port) crossing a threshold of an active alarm.
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Event acIDSBlacklistNotification Default Severity Event Type securityServiceOrMechanismViolation Probable Cause thresholdCrossed Alarm Text "Added IP * to blacklist" "Removed IP * from blacklist" Status Changes Corrective Action Identify the malicious remote host (IP address / port) that the Intrusion Detection System (IDS) has automatically blacklisted or removed from the blacklist.
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Event acWebUserAccessDisabled access). The Web security administrator must: In the Web interface, access the Local Users table ( Setup menu > Admin- istration tab > Web & CLI folder > Local Users ).
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Keep-Alive Trap Table 7-60: acKeepAlive Event acKeepAlive 1.3.6.1.4.1.5003.9.10.1.21.2.0.16 Description Part of the NAT traversal mechanism. If the device's STUN application detects a NAT, this trap is sent on a regular time laps - 9/10 of the acSysSTUNBindingLifeTime object.
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Event acPerformanceMonitoringThresholdCrossing Description The alarm is sent every time the threshold of a Performance Monitored object ('Minimum', 'Average', 'Maximum', 'Distribution below/above/between thresholds', and 'Low and high thresholds') is crossed. The severity field is 'Indeterminate' when the crossing is above the threshold and 'Cleared' when it goes back under the threshold.
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Event acHTTPDownloadResult Description The alarm is sent upon success or failure of the HTTP Download action. Default Indeterminate Severity Event Type processingErrorAlarm (3) for failures and other (0) for success.
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide High-Availability (HA) This section describes the SNMP trap events concerned with the High-Availability (HA) system. Redundant Board Trap Table 7-64: acRedundantBoardAlarm Event acRedundantBoardAlarm 1.3.6.1.4.1.5003.9.10.1.21.2.0.97 Description The notification trap is sent by the active device when an alarm or notification is sent by the redundant device: ■...
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Event acRedundantBoardAlarm Probable Other (0) Cause Condition Alarm or notification is sent in the redundant device Trap Text Hitless Software Upgrade Status Trap Table 7-65: acHitlessUpdateStatus Event acHitlessUpdateStatus 1.3.6.1.4.1.5003.9.10.1.21.2.0.48 Description The notification trap is sent at the beginning and end of a Hitless Software Upgrade, which is used in the High Availability system.
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Event acHitlessUpdateStatus parameter." "Hitless fail: Hitless Upgrade failed because the cmp Replace the cmp file with a SW ver file is invalid. The number of characters valid one stream name defining the software version stream too long."...
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Event acSSHConnectionStatus Changes Condition SSH connection attempt Text Value %s – remote IP %s – user name Condition SSH connection attempt – success of failure SIP Proxy Connection Lost per Proxy Set Trap...
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Event acProxyConnectivity connected to this same proxy, check if there are more Audi- oCodes devices with the same trap event. If this is the case, this could confirm that this is not an issue with the device.
Mediant 800 SBC | SNMP Reference Guide Event authenticationFailure access permission or incorrectly authenticated protocol message. Categorized by the RFC as an “enterprise-specific trap”. Board Initialization Completed Trap This is the AudioCodes Enterprise application cold start trap. Table 7-70: acBoardEvBoardStarted Event acBoardEvBoardStarted 1.3.6.1.4.1.5003.9.10.1.21.2.0.4 Description The alarm is sent after the device is successfully restored and initialized following reset.
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Link Up Trap Table 7-72: linkUp Event linkUp 1.3.6.1.6.3.1.1.5.4 IF-MIB Description The alarm is sent if the operational status of a communication link changes from “down”. Categorized by the RFC as an “enterprise-specific trap”.
Page 181
CHAPTER 7 SNMP Traps Mediant 800 SBC | SNMP Reference Guide Event acEnhancedBITStatus their status. Status Changes Additional Info-1 BIT Type: Offline, startup, periodic Additional Info-2 BIT Results: ■ BIT_RESULT_PASSED ■ BIT_RESULT_FAILED Additional Info-3 Buffer: Number of bit elements reports Corrective Action...
The two latter options require the STUN client be enabled (ini file parameter [EnableSTUN]). In addition, once the acKeepAlive trap is instigated it does not stop. ■ The manager can view the NAT type in the MIB: audioCodes(5003).acProducts (9).acBoardMibs(10).acSystem(10).acSystemStatus(2).acSysNetwork(6).acSysNAT (2).acSysNATType(1) ■...
CHAPTER 8 Advanced SNMP Features Mediant 800 SBC | SNMP Reference Guide ■ The first few objects are scalars that are read-only objects for the dry-contacts’ state. ■ acSysModuleTable: A table containing mostly status information that describes the modules in the system. In addition, the table can be used to reset an entire system, reset a redundant module or perform switchover when for devices supporting HA.
Page 184
CHAPTER 8 Advanced SNMP Features Mediant 800 SBC | SNMP Reference Guide ● 1: waits until all calls are terminated (i.e., perform a Graceful shutdown) ● > 0: the number of seconds to wait before the graceful shutdown turns into a force...
CHAPTER 9 Getting Started with SNMP Mediant 800 SBC | SNMP Reference Guide Getting Started with SNMP This section provides a getting started for quickly setting up the device for management using AudioCodes SNMP MIBs. Basic SNMP Configuration Setup This subsection provides a description of the required SNMP configuration when first accessing the SNMP agent running on the device.
Page 186
CHAPTER 9 Getting Started with SNMP Mediant 800 SBC | SNMP Reference Guide In addition, you can associate a trap destination with a specific SNMPv3 USM user. Traps will be sent to that trap destination using the SNMPv3 format and the authentication and privacy protocol configured for that user.
CHAPTER 9 Getting Started with SNMP Mediant 800 SBC | SNMP Reference Guide If a row does not already exist for this combination of user and SecurityLevel, add a row to the snmpTargetParamsTable with this values: Name=usm<user> MPModel=3(SNMPv3) SecurityModel=3 (usm) SecurityName=<user>...
Page 188
CHAPTER 9 Getting Started with SNMP Mediant 800 SBC | SNMP Reference Guide ● The concept of trusted managers is a weak form of security and is therefore, not a required part of SNMPv3 security, which uses authentication and privacy. ●...
(config-system)# snmp settings (snmp)# trusted-managers Getting Acquainted with AudioCodes MIBs AudioCodes proprietary MIBs are located in the AudioCodes subtree (OID 1.3.6.1.4.1.5003). A classification within the subtree separates the MIBs according to the following: ■ Configuration and status MIBs – in the acBoardMibs subtree . The different MIB modules are grouped according to different virtual modules of the device.
Page 190
CHAPTER 9 Getting Started with SNMP Mediant 800 SBC | SNMP Reference Guide MEGACO and MGCP (amongst these are also the SIP relevant objects) and subtrees that are specific to the different CPs. ● acAnalog MIB: all objects in this MIB are related only to the configuration, status and line testing or resetting of analog interfaces..
CHAPTER 9 Getting Started with SNMP Mediant 800 SBC | SNMP Reference Guide Traps and Alarms The device supports standard traps and proprietary traps. Most of the proprietary traps are alarm traps, that is, they can be sent and cleared. Thus, they are referred to as alarm traps. All the standard traps are non-alarm traps, referred to as log traps.
CHAPTER 9 Getting Started with SNMP Mediant 800 SBC | SNMP Reference Guide (config-system)# snmp trap (snmp-trap)# community-string ■ SNMPv3 Settings: When using SNMPv3 settings it is important to note that by default the trap configuration remains such that the traps are sent out in SNMPv2c mode. To have traps sent out in SNMPv3, you can use either ini file or SNMP: ●...
Page 193
CHAPTER 9 Getting Started with SNMP Mediant 800 SBC | SNMP Reference Guide ■ The device allows a manager to determine which alarms are currently active in the device. That is, the device maintains an active alarm table. ■ The device allows a manager to detect lost alarms and clear notifications (sequence number in trap, current sequence number MIB object).
Page 194
CHAPTER 9 Getting Started with SNMP Mediant 800 SBC | SNMP Reference Guide This page is intentionally left blank. - 185 -...