Summary of Contents for Middle Atlantic Products VDM Series
Page 1
Instruction Sheet VDM CEILING MOUNT SERIES Single Sided VDM-600-CM VDM-2X1-CM VDM-3X1-CM VDM-2X1-CM Shown Back to Back VDM-600-B2B-CM VDM-2X1-B2B-CM VDM-3X1-B2B-CM VDM-2X1-B2B-CM Shown THANK YOU Thank you for purchasing the VDM ceiling monitor mounts. Please read these instructions thoroughly before installing or assembling these products. PRODUCT FEATURES •...
IMPORTANT SAFETY INSTRUCTIONS • Read these instructions. • Heed all warnings. • Clean only with dry cloth. • Keep these instructions. • Follow all instructions. • Only use attachments/accessories specified by the manufacturer. DANGER HAZARDOUS VOLTAGE: The lightning flash with the WARNING: A warning alerts you to a situation that could result arrowhead symbol, within an equilateral triangle is intended to alert the in serious personal injury or death.
Page 5
SUPPLIED COMPONENTS FOR VDM-600-CM & VDM-600-B2B-CM Display Mount Tilt Bracket Extrusion Pole Mount Model Qty. Model Qty. Model Qty. VDM-600-CM VDM-600-CM VDM-600-CM VDM-600-B2B-CM VDM-600-B2B-CM VDM-600-B2B-CM Pan Head Phillips Screw Flat Head Screw End Cap Model Qty. Model Qty. Model Qty. VDM-600-CM VDM-600-CM VDM-600-CM...
Page 6
SUPPLIED COMPONENTS FOR VDM-2X1-CM & VDM-2X1-B2B-CM Display Mount Tilt Bracket Extrusion (2x) Pole Mount Model Qty. Model Qty. Model Qty. VDM-2X1-CM VDM-2X1-CM VDM-2X1-CM VDM-2X1-B2B-CM VDM-2X1-B2B-CM VDM-2X1-B2B-CM Long Pan Head Screw Flat Head Screw End Cap Model Qty. Model Qty. Model Qty.
Page 7
SUPPLIED COMPONENTS FOR VDM-3X1-CM & VDM-3X1-B2B-CM Display Mount Tilt Bracket Extrusion (2x) Pole Mount Model Qty. Model Qty. Model Qty. VDM-3X1-CM VDM-3X1-CM VDM-3X1-CM VDM-3X1-B2B-CM VDM-3X1-B2B-CM VDM-3X1-B2B-CM Pan Head Phillips Screw Flat Head Screw End Cap Model Qty. Model Qty. Model Qty.
Page 8
SUPPLIED COMPONENTS - (CONTINUED) DISPLAY HARDWARE KITS Below display mount hardware supplied in kits. Model Kit Qty. Model Kit Qty. Model Kit Qty. VDM-600-CM VDM-2X1-CM VDM-3X1-CM VDM-600-B2B-CM VDM-2X1-B2B-CM VDM-3X1-B2B-CM Display Mount Screws M8 x 16 M8 x 20 M8 x 40 M6 x 12 M6 x 20 M6 x 30...
AVERTISSEMENT: Utiliser des outils avec prudence et suivre tous les protocoles de sécurité nécessaires. CEILING MOUNT INSTALLATION SPACING 1. Install your Middle Atlantic Products ceiling mount and extension poles to the spacing dimension shown for your display mounting system. (FIGURE A) Model...
Page 10
CEILING MOUNT INSTALLATION SPACING 1. Thread pole mount(s) (A) to preinstall extension pole(s) as far as they will go. (FIGURE B) 2. For systems using two pole mounts, align and orient pole mounts as shown. (FIGURE C) 3. Insert (2x) set screw (U) into both sides of theaded collar and tighten using hex key (T). (FIGURE B) FIGURE B FIGURE C Page 10...
Page 11
EXTRUSION INSTALLATION 1. Slide extrusion brackets (B) onto back of extrusion (C) oriented as shown. (FIGURE D) Model Extrusion Bracket (B) Qty. VDM-600-CM VDM-600-B2B-CM VDM-2X1-CM VDM-2X1-B2B-CM VDM-3X1-CM VDM-3X1-B2B-CM FIGURE D 2. Hook extrusion assembly onto each pole mount (A) as shown. For B2B models, repeat assembly process on opposite side of pole mount (A) (FIGURE E) Extension pipes sold seperately...
TILT ADJUSTMENT 1. Tilt bracket (B) is designed with 20˚ full range adjustment or preset holes in 5˚ increments. If angle is already known set all tilt brackets to the preset angle by installing (2x) pan head phillips screws (J) into preset hole on each side of tilt bracket.
Page 13
FLUSH DISPLAY MOUNT BRACKET INSTALLATION 1. Using supplied display mount screws,select the appropriate screw size and length ensuring screw does not bottom out in mounting hole, or damage to display may occur. If you feel resistance, stop immediately and try a shorter screw. If supplied screws are still too long, use supplied spacers to take up slack.
Page 14
RECESSED OR RAISED BACK DISPLAY MOUNT BRACKET INSTALLATION 1. Using supplied display mount screws,select the appropriate screw size and length ensuring screw does not bottom out in mounting hole, or damage to display may occur. If you feel resistance, stop immediately and try a shorter screw.
Page 15
HANGING DISPLAY 1. Tilt display and hook display bracket onto flange of tilt bracket (B). (FIGURE K) 2.Push along the bottom of display until the mount clicks into place. (FIGURE K) 3. To remove display from the extrusion, pull both release cord rings down while pulling bottom of display away from wall and lift display off flange of extrusion.
Page 16
Micro Adjustments 1. If the display is uptilted, rotate the adjustment screws as shown in figure below using hex wrench (S). (FIGURE L) FIGURE L 2. Rotate the adjustment screws as shown below to make adjustments to align displays using hex wrench (S).
FINAL ASSEMBLY 1. With ends of extrusion evenly spaced between brackets, install button head socket screw (K) into back of each tilt bracket (B) (either left or right side of bracket) to secure extrusion in place using hex key (T). Repeat process for each extrusion bracket. (FIGURE N) Model Screw (K) Qty.
Voice: 613-836-2501 - Fax: 613-836-2690 / ca.middleatlantic.com - customerservicecanada@middleatlantic.ca Factory Distribution USA: NJ - CA - IL Canada: ON - BC At Middle Atlantic Products we are always listening. Your comments are welcome. Middle Atlantic Products is an ISO 9001 and ISO 14001 Registered Company. Page 18...