Table of Contents
Advertisement
Quick Links
Instruction Sheet
Dynamic Monitor Mount Series
MM3-C
Clamp Mount
ViewPoint™ Series
Grommet Mount
Console System
Mount
THANK YOU
Thank you for purchasing an MM3-C Dynamic Monitor Mount. Please read these instructions
thoroughly before installing or assembling this product.
PRODUCT FEATURES
• Accepts up to 32" Monitor
100-00027
Rev A
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Middle Atlantic Products MM3-C Series
Summary of Contents for Middle Atlantic Products MM3-C Series
- Page 1 Instruction Sheet Dynamic Monitor Mount Series MM3-C Clamp Mount ViewPoint™ Series Grommet Mount Console System Mount THANK YOU Thank you for purchasing an MM3-C Dynamic Monitor Mount. Please read these instructions thoroughly before installing or assembling this product. PRODUCT FEATURES •...
-
Page 2: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS • Read these instructions. • Heed all warnings. • Clean only with dry cloth. • Keep these instructions. • Follow all instructions. • Only use attachments/accessories specified by the manufacturer. DANGER HAZARDOUS VOLTAGE: The lightning flash with the WARNING: A warning alerts you to a situation that could result arrowhead symbol, within an equilateral triangle is intended to alert the in serious personal injury or death. -
Page 3: Weight Ratings
WEIGHT RATINGS Model Number Each Display Maximum Total Rated Load MM3-C-120-BK 25 lbs. (11.34 kg) 25 lbs. (11.34 kg) MM3-C-220-BK 25 lbs. (11.34 kg) 50 lbs. (22.68 kg) MM3-C-330-BK 20 lbs. (9.07 kg) 60 lbs. (27.2 kg) MM3-C-420-BK 18 lbs. (8.16 kg) 72 lbs. - Page 4 SUPPLIED COMPONENTS AND HARDWARE ALL MODELS INCLUDE: Grommet Cup Mount Plate Plate Adapter Plate Clamp Assembly (B) Clamp Assembly (A) (Models MM3-C-120, (Model MM3-C-420) MM3-C-220, MM3-C-330 Only) Adhesive Longer Short Long Flat Head Set Screw Knob (J x 5) Carriage Bolt Carriage Bolt Hex Screw (H x 2)
- Page 5 INTRODUCTION NOTE: • Follow all topics in their order of appearance. • Installation procedures apply to all series models unless otherwise specified in topic titles and notes. MOUNTING THE BASE USING THE GROMMET GROMMET MOUNTING 1. Insert long carriage bolt (N) through adapter plate (C) as shown. (FIGURE A) 2.
- Page 6 MOUNTING THE BASE USING THE CLAMP CLAMP MOUNTING Attach pole base (F) to clamp assembly (A) using (4x) flat head screws (M) and tighten using 4mm hex key (Q) as shown. (FIGURE B) Apply ( x) adhesive pads (J) around the bottom of clamp bracket (A) evenly spaced. Slide assembly over work surface and tighten securely in place.
- Page 7 MOUNTING THE BASE TO A VIEWPOINT CONSOLE VIEWPOINT CONSOLE MOUNTING 1. Insert short carriage bolt (L) into cup mount plate (E) as shown. (FIGURE C) 2. Attach cup mount plate (E) to pole base (F) using (4x) flat head screws (M) and tighten using 4mm hex key (Q) as shown.
- Page 8 MOUNTING THE ARM ASSEMBLY TO THE POLE BASE 1. Insert arm assembly (Z) into pole base (F). 2. Tighten set screws in the pole base (F) against the arm assembly (Z). NOTE: If set screws (shipped in the pole base) do not contact the outer diameter of the pole when tightened but are instead lined up to reach into the pole channels, replace the set screws with the longer set screws (H).
- Page 9 MM3-C-420 ONLY: INSTALLING ADD-ON ARM ASSEMBLIES 1. Loosely install two #10-24 x 5/8" flat head cap screws (AE) through holes on each add-on arm assembly (AC) and into two #10-24 square nuts (AD). (See Figure F) 2. Remove pole cap from column. (See Figure G) 3.
-
Page 10: Display Installation
DISPLAY INSTALLATION 1. Remove quick release faceplate from mount by pulling quick release lever and sliding faceplate up and off mount. (See Figure H) quick release lever FIGURE H 2. Carefully place display face down on protective surface. 3. Connect faceplate to display For flush mounting hole installation: Using Phillips screwdriver, carefully install four M4x10mm screws (T) through corresponding holes on •... -
Page 11: Pitch Adjustment
ADJUSTMENTS Pitch Adjustment 1. Adjust pitch to desired tilt position. (See Figure K) 2. Adjust pitch tension screw to change the adjustment tension. (See Figure K) Pivot Adjustment 3. Adjust pivot position as desired. (See Figure K) 4. Use 3/16” hex key (Y) to adjust pivot point tension screws to change pivot adjustment tension. (See Figure K) Rotational tension Pivot point tension... -
Page 12: Display Removal
DISPLAY REMOVAL Only remove display from mount when the display can be lifted up from the mount! DO NOT remove WARNING: display unless the display is in the upright position! (See Figure N) 1. Make sure display is in the upright position. 2. - Page 13 PIVOT ADJUSTMENT RANGE MM3-C-120 • 1. Adjust arm angle as desired up to 90 degrees in either direction. (See Figure P) WARNING: Swinging the arm beyond 90 degrees may result in the mount slipping off the surface causing serious injury! (top view) pivot point of the arm Mounting point...
-
Page 14: Cable Management
CABLE MANAGEMENT 1. Press insides of cable management covers at both ends to unhinge tabs on either end of cable management cover on upper arm. (See Figure R) 2. Lift cable management cover up until tabs are unhinged and cover is in the “open” position. (See Figure R) 3. -
Page 15: Warranty
Voice: +31 (0) 495 726002 - av.emea.middleatlantic.support@legrand.com Factory Distribution United States: New Jersey, California, Illinois - Canada: Ontario - The Netherlands: Weert At Middle Atlantic Products we are always listening. Your comments are welcome. Middle Atlantic Products is an ISO 9001 and ISO 14001 Registered Company.
Need help?
Do you have a question about the MM3-C Series and is the answer not in the manual?
Questions and answers