Middle Atlantic Products VDM Series Instruction Sheet
Fixed & tilt wall mount
Hide thumbs
Also See for VDM Series:
- Instruction sheet (18 pages) ,
- Instruction sheet (12 pages) ,
- Instruction sheet (14 pages)
Advertisement
Quick Links
FIXED & TILT WALL MOUNT
VDM-400-F & VDM-600-F
THANK YOU
Thank you for purchasing a Vision Display fixed or tilt wall mount.
Please read these instructions thoroughly before installing or assembling these products.
PRODUCT FEATURES
• Open wall plate design maximizes accessibility to connections and cable pass-through behind
the display
• Post-install leveling mechanism enables quick micro-adjustment of horizontal plane of display
• Safety locking features keep the display securely mounted
• VESA Capability:
VDM-400-F & VDM-400-T 75x75mm - 400x400mm
VDM-600-T & VDM-600-T 75x75mm - 600x400mm
Instruction Sheet
VDM Series
VDM-400-T & VDM-600-T
I-00807
Rev A
Advertisement
Related Manuals for Middle Atlantic Products VDM Series
Summary of Contents for Middle Atlantic Products VDM Series
- Page 1 Instruction Sheet VDM Series FIXED & TILT WALL MOUNT VDM-400-F & VDM-600-F VDM-400-T & VDM-600-T THANK YOU Thank you for purchasing a Vision Display fixed or tilt wall mount. Please read these instructions thoroughly before installing or assembling these products.
- Page 2 IMPORTANT SAFETY INSTRUCTIONS / INSTRUCTIONS IMPORTAANTES SUR LA SÉCURITÉ SAVE ALL INSTRUCTIONS / CONSERVER CES INSTRUCTIONS WARNING/AVERTISSEMENT and the exclamation point within an CAUTION/ATTENTION and the exclamation point within an equilateral triangle is intended to alert the user to the possibility of equilateral triangle is intended to alert the user to the possibility of serious injury or death if the instructions are not followed.
-
Page 3: Weight Ratings
WEIGHT RATINGS Model Weight Rating VDM-400-F 150 lbs. Maximum Total Rated Load VDM-400-T 150 lbs. Maximum Total Rated Load VDM-600-F 180 lbs. Maximum Total Rated Load VDM-600-T 180 lbs. Maximum Total Rated Load TOOLS REQUIRED • #2 Phillips Screwdriver • Drill •... - Page 4 COMPONENTS SUPPLIED (CONTINUED) (12) Hex Head Screw Wall Anchor M5 Washer M8 Washer Display Mount Spacers M6 Short Spacer M6 Long Spacer M8 Short Spacer M8 Long Spacer Display Mount Screws M4 x 16 M5 x 12 M5 x 16 M5 x 30 M4 x 12 M4 x 20...
- Page 5 WOOD STUD WALL BRACKET INSTALLATION 1. Determine height for display and find center of stud closest to desired position on wall. Locate the center of the second stud to the left or right of desired location. 2. Using a level, scribe a 10” long line down the center of both studs at the desired height. (FIGURE A) FIGURE A 3.
- Page 6 WOOD STUD WALL BRACKET INSTALLATION CONT. 1) Install wall mounting bracket (A) using (4x) hex head screw (D) and (4x) washer (F). (FIGURE C) FIGURE C BLOCK OR CEMENT WALL BRACKET INSTALLATION 1. Determine position and height for display. Using a level and the wall mount bracket (A) as a template, mark the center of the 4 mounting slots that are spaced the farthest apart.
- Page 7 BLOCK OR CEMENT WALL BRACKET INSTALLATION CONT. 2. Remove wall mount bracket and using a 7/16” drill bit, drill a 2.5” deep hole in each of the 4 marked center points. (FIGURE E) 3. Press a wall anchor (E) into each of the 4 drilled holes. NOTE: Wall anchors may require a hammer to install.
- Page 8 STOP These display mounts are supplied with a Proximity Series Mounting Plate PRX-MP-9X12. Before installing display mounting brackets to your display, follow the supplied mounting plate installation instructions I-00804 to find the best location for mounting your plate. Page 8...
- Page 9 DISPLAY MOUNT BRACKET INSTALLATION 1. Using supplied display mount screws, select the appropriate screw size and length ensuring screw does not bottom out in mounting hole, or damage to display may occur. If you feel resistance, stop immediately and try a shorter screw.
- Page 10 RECESSED OR RAISED BACK DISPLAY MOUNT BRACKET INSTALLATION 1. Using supplied display mount screws, select the appropriate screw size and length ensuring screw does not bottom out in mounting hole, or damage to display may occur. If you feel resistance, stop immediately and try a shorter screw.
- Page 11 HANGING DISPLAY (FIXED MOUNT) 1. Tilt display and hook display bracket onto flange of wall mount bracket (A). Standoff support may be used to prevent display from locking into place while connecting wires. (FIGURE J) 2. Swing standoff support up to lower display in place. push along the bottom of display until the mount clicks into place.
- Page 12 HANGING DISPLAY (TILT MOUNT) 1. Tilt display and hook onto flange of wall mounting bracket. (FIGURE P) 2. Push along the bottom of display until the mount clicks into place. (FIGURE R) 3. To remove display from the wall mount bracket, pull both release cord rings down while pulling bottom of display away from wall.
- Page 13 ADJUSTING DISPLAY TILT (VDM-400-T & VDM-600-T ONLY) 1. To tilt display, loosen wing screws on both display mount brackets. 2. Grab top and bottom of display and carefully pull top of display gently to desired angle. Tighen both wing screws to lock display at desired angle. 3.
-
Page 14: Warranty
- customerservicecanada@middleatlantic.ca Factory Distribution USA: NJ - CA - IL Canada: ON - BC At Middle Atlantic Products we are always listening. Your comments are welcome. Middle Atlantic Products is an ISO 9001 and ISO 14001 Registered Company. Page 14...