Middle Atlantic Products VDM Series Instruction Sheet
Tilt low profile mount
Hide thumbs
Also See for VDM Series:
- Instruction sheet (18 pages) ,
- Instruction sheet (12 pages) ,
- Instruction sheet (14 pages)
Advertisement
Quick Links
VDM-400-T-LP
VDM-600-T-LP
VDM-800-T-LP
THANK YOU
Thank you for purchasing the Vision Display fixed low profile wall mount.
Please read these instructions thoroughly before installing or assembling these products.
PRODUCT FEATURES
• Open wall plate design maximizes accessibility to connections and cable pass-through behind
the display
• Post-install leveling mechanism enables quick micro-adjustment of horizontal plane of display
• Safety locking features keep the display securely mounted
• VESA Capability:
VDM-400-T-LP 75x75mm - 400x400mm
VDM-600-T-LP 75x75mm - 600x400mm
VDM-800-T-LP 75x75mm - 800x600mm
Instruction Sheet
VDM Series
Tilt Low Profile Mount
I-00810
Rev A
Advertisement
Related Manuals for Middle Atlantic Products VDM Series
Summary of Contents for Middle Atlantic Products VDM Series
- Page 1 Instruction Sheet VDM Series Tilt Low Profile Mount VDM-400-T-LP VDM-600-T-LP VDM-800-T-LP THANK YOU Thank you for purchasing the Vision Display fixed low profile wall mount. Please read these instructions thoroughly before installing or assembling these products. PRODUCT FEATURES • Open wall plate design maximizes accessibility to connections and cable pass-through behind the display •...
- Page 2 IMPORTANT SAFETY INSTRUCTIONS / INSTRUCTIONS IMPORTAANTES SUR LA SÉCURITÉ SAVE ALL INSTRUCTIONS / CONSERVER CES INSTRUCTIONS WARNING/AVERTISSEMENT and the exclamation point within an CAUTION/ATTENTION and the exclamation point within an equilateral triangle is intended to alert the user to the possibility of equilateral triangle is intended to alert the user to the possibility of serious injury or death if the instructions are not followed.
-
Page 3: Weight Ratings
WEIGHT RATINGS Model Weight Rating VDM-400-T-LP 80 lbs. Maximum Total Rated Load VDM-600-T-LP 100 lbs. Maximum Total Rated Load VDM-800-T-LP 150 lbs. Maximum Total Rated Load TOOLS REQUIRED • #2 Phillips Screwdriver • Drill • Protective Eyewear • 5/32” Wood Bit or 3/8“ Masonary Bit •... - Page 4 COMPONENTS SUPPLIED (CONTINUED) (VDM-400-T-LP Qty 4) M8 Washer M5 Washer (VDM-400-T-LP Qty 4) (VDM-600-T-LP Qty 6) (VDM-600-T-LP Qty 6) (VDM-800-T-LP Qty 6) (VDM-800-T-LP Qty 6) #14 x 2.5” Wall Anchor Hex Screw Display Mount Spacers (VDM-600-T-LP Qty 4) M6 Short Spacer M6 Long Spacer M8 Short Spacer (VDM-800-T-LP Qty 4)
- Page 5 WOOD STUD WALL BRACKET INSTALLATION VDM-400-T-LP & VDM-600-T-LP Models only 1. Determine height for display and find center of stud closest to desired position on wall. Locate the center of the second stud to the left or right of desired location. 2.
- Page 6 WOOD STUD WALL BRACKET INSTALLATION CONT. 4. Remove wall mount bracket and using a 5/32” drill bit, drill a 2.5” deep pilot hole in each of the 4 marked center points. 5) Install wall mounting bracket using (4x) #14 x 2.5” Hex Screw (F). Orient wall mounting bracket as shown. (FIGURE C) Arrow must face up FIGURE C...
- Page 7 WOOD STUD WALL BRACKET INSTALLATION VDM-800-T-LP only 1. Determine height for display and find center of stud closest to desired position on wall. Locate the center of the stud to the left and right of desired location (3 studs total). 2.
- Page 8 WOOD STUD WALL BRACKET INSTALLATION CONT. 4. Remove wall mount bracket and using a 5/32” drill bit, drill a 2.5” deep pilot hole in each of the 6 marked center points. 5) Install wall mounting bracket using (6x) #14 x 2.5” Hex Screw (F). Orient wall mounting bracket as shown. (FIGURE F) Arrow must face up FIGURE F...
- Page 9 VDM-400-F-LP BLOCK OR CEMENT WALL BRACKET INSTALLATION VDM-400-T-LP only 1. Determine position and height for display. Using a level and the wall mount bracket (A) as a template, mark the center of the 4 mounting slots that are spaced the farthest apart. (FIGURE G) Mounting slots FIGURE G 2.
- Page 10 BLOCK OR CEMENT WALL BRACKET INSTALLATION CONT. 4. Install wall mounting bracket using (4x) #14 x 2.5” Hex Screws (F). Orient wall mounting bracket as shown. (FIGURE J) NOTE: To prevent anchors from Arrow must face up stripping, only use a hand tool to install.
- Page 11 BLOCK OR CEMENT WALL BRACKET INSTALLATION CONT. VDM-600-T-LP and VDM-800-T-LP Models only 1. Determine position and height for display. Using a level and the wall mount bracket (A) as a template, mark the 2 center slots and 4 mounting slots that are spaced the farthest apart on both ends of wall bracket (total 6). (FIGURE K) Mounting slots FIGURE K...
- Page 12 BLOCK OR CEMENT WALL BRACKET INSTALLATION CONT. 4. Install wall mounting bracket using (6x) #14 x 2.5” Hex Screws (F). Orient Wall Mounting Bracket as shown. (FIGURE M) NOTE: To prevent anchors from stripping, only use a hand tool to install. Arrow must face up FIGURE M Page 12...
- Page 13 DISPLAY BRACKET EXTENSION INSTALLATION VDM-800-T-LP ONLY 1. For larger displays, it may be necessary to attach extension bracket (C) to align display mounting bracket (B) mounting holes with VESA holes in display using (8x) Extension Screws (D). Page 13...
- Page 14 DISPLAY MOUNT BRACKET INSTALLATION 1. Using supplied display mount screws, select the appropriate screw size and length ensuring screw does not bottom out in mounting hole, or damage to display may occur. If you feel resistance, stop immediately and try a shorter screw.
- Page 15 RECESSED OR RAISED BACK DISPLAY MOUNT BRACKET INSTALLATION 1. Using supplied display mount screws,select the appropriate screw size and length ensuring screw does not bottom out in mounting hole, or damage to display may occur. If you feel resistance, stop immediately and try a shorter screw.
- Page 16 HANGING DISPLAY 1. Tilt display and hook display bracket onto flange of wall mount bracket (A). Standoff support may be used to prevent display from locking into place while connecting wires. (FIGURE R) 2. Swing standoff support up to lower display in place. Push along the bottom of display until the mount clicks into place.
- Page 17 ADJUSTING DISPLAY TILT 1. To tilt display, grab top and bottom of display and carefully pull top of display gently to desired angle. 3. To return display to a vertical position, grab top and bottom of display, carefully push display from the top. Once display is vertical, mount will snap into place holding the display from tilting.
-
Page 18: Warranty
- customerservicecanada@middleatlantic.ca Factory Distribution USA: NJ - CA - IL Canada: ON - BC At Middle Atlantic Products we are always listening. Your comments are welcome. Middle Atlantic Products is an ISO 9001 and ISO 14001 Registered Company. Page 18...