Electronic Pinouts And Schematics; Spike-2 Cpu Node 0 - Stern Pinball LED ZEPPELIN PRO Service And Operation Manual

ELECTRONIC PINOUTS AND SCHEMATICS

4. ELECTRONIC PINOUTS AND SCHEMATICS

4.1 SPIKE-2 CPU NODE 0

509-1003-01
DIRECT SWITCH MAPPING (CN25)
The coin-door diagnostic switches are connected directly to the CPU node via the Cabinet Node. Note that both the CPU and
Cabinet nodes are required for diagnostic switch operation.
ID Name Conn.
C1 DIP 1 -
C2 DIP 2 -
C3 DIP 3 -
C4 DIP 4 -
C5 DIP 5 -
C6 DIP 6 -
C7 DIP 7 -
C8 DIP 8 -
C9 Service Select CN25
C10 Service Plus CN25
C11 Service Minus CN25
C12 Service Back CN25
CONNECTORS
ID Connector Type
CN1 5-Pin .156" Header
CN2 3-Pin .100" Header
CN3 7-Pin .100" Header
CN4 2-Pin .156"
CN5 7-Pin .100" Header
CN6 34 Pin 2.00mm Header
CN7 5-Pin .156" Header
CN8 6-Pin .100" Header
CN9 USB
CN9 USB
CN10 HDMI
CN11 RJ45
CN12 RJ45
CN13 SD CARD
CN14 5-Pin .100" Header
CN15 3-Pin .100" Header
CN16 4-Pin .100" Header
CN17 ETHERNET
CN21 SATA Header
CN22 RJ45
CN25 12-Pin .100" Header
30
Input Input Wire GND
Pin Pin
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
1 LGN-GRY 11
2 LGN-VIO 11
3 LGN-BLU 11
4 LGN-BLK 11
Description
Backbox 2-channel amplified speaker out
Console Port
Headphone connector
Cabinet 1-channel amplified speaker out
Line In/Out
LCD display connector
48V supply from main power supply
SPI Serial
USB connector - for software updates,
audit dumps, and expansion modules
USB connector - for software updates,
audit dumps, and expansion modules
HDMI Out
SPIKE node bus - to cabinet node N1
SPIKE node bus - To Topper accessory Kit
SD Card connector
LCD Backlight
Backbox Light
3.3v / 5v / 12v
ETHERNET connector
SATA connector
SPIKE node bus - to playfield node
Dedicated switch inputs - service, volume
switches
LED ZEPPELIN PRO MANUAL 500-55R5-01
Ground Wire Location Type
- CPU Node
- CPU Node
- CPU Node
- CPU Node
- CPU Node
- CPU Node
- CPU Node
- CPU Node
BLK-WHT Coin Door
BLK-WHT Coin Door
BLK-WHT Coin Door
BLK-WHT Coin Door
COMPONENTS
ID Name
S1 DIP Switches
S2 Reset Switch
SD CARD (CN13) For system SD card. Note: only to be removed if instructed to by
Stern Service.
BT1 BR1225 3V Lithium battery for game clock between power cycles
STATUS LEDS
LED ID Name Color Description
48V +48V Supply In Red
3.3V +3.3V Logic Red
5V +5V Logic Red
12V +12V Backbox Red
Illumination
VA +30V Audio Red
VNB +9V Node Bus Red
5V (CPU) +5V Logic Red
SDIO ACT Not Used Red
STATUS CPU Heartbeat, Red
System Status
μSD ACT Activity indicator Red
for micro SD Card
D23 Netbridge Status Red
Address Part Number
0-SW-0 -
0-SW-1 -
0-SW-2 -
0-SW-3 -
0-SW-4 -
0-SW-5 -
0-SW-6 -
0-SW-7 -
0-SW-9 515-1963-00
0-SW-10 515-1963-00
0-SW-11 515-1963-00
0-SW-12 515-1963-00
ON: Main system power is connected.
OFF: No 48V system power. Check power sup-
ply connections, cables, and fuses.
ON: Logic power supply is good.
OFF: Logic power supply bad, call tech support.
ON: Logic power supply is good.
OFF: Logic power supply bad, call tech support.
ON: Back box LED power good.
OFF: Backbox LED power bad, call tech
support.
ON: Audio power supply is good.
OFF: Audio power supply off, call tech support.
Power for the Node bus. ON: Power for node
bus good.
OFF: Power to node bus not detected, call tech
support.
ON: Logic power supply is good.
OFF: Logic power supply bad, call tech support.
Should remain unlit as it is not currently used.
Double blink ~1/2 second: Good, Processor
running. OFF: Processor not running, call tech
support.
Should blink rapidly when reading or writing to
micro SD card.
Should blink once every ~1/2 second.
©2020 Mythgem, LTD.