Electronic Pinouts And Schematics; Spike-2 Cpu Node 0 - Stern Pinball JAMES BOND 007 LE Service And Operation Manual

4. ELECTRONIC PINOUTS AND SCHEMATICS

4.1 SPIKE-2 CPU NODE 0

509-1003-01
DIRECT SWITCH MAPPING (CN25)
The coin-door diagnostic switches are connected directly to the CPU node via the Cabinet Node. Note that both the CPU and
Cabinet nodes are required for diagnostic switch operation.
ID Name Conn.
C1 DIP 1 -
C2 DIP 2 -
C3 DIP 3 -
C4 DIP 4 -
C5 DIP 5 -
C6 DIP 6 -
C7 DIP 7 -
C8 DIP 8 -
C9 Service Select CN25
C10 Service Plus CN25
C11 Service Minus CN25
C12 Service Back CN25
CONNECTORS
ID Connector Type Description
CN1 5-Pin .156" Header Backbox 2-channel amplified speaker out
CN2 3-Pin .100" Header Console Port
CN3 7-Pin .100" Header Headphone connector
CN4 2-Pin .156" Cabinet 1-channel amplified speaker out
CN5 7-Pin .100" Header Line In/Out
CN6 34 Pin 2.00mm Header LCD display connector
CN7 5-Pin .156" Header 48V supply from main power supply
CN8 6-Pin .100" Header SPI Serial
CN9 USB USB connector - for software updates,
audit dumps, and expansion modules
CN9 USB USB connector - for software updates,
audit dumps, and expansion modules
CN10 HDMI HDMI Out
CN11 RJ45 SPIKE node bus - to cabinet node N1
CN12 RJ45 SPIKE node bus - To Topper accessory Kit
CN13 SD CARD SD Card connector
CN14 5-Pin .100" Header LCD Backlight
CN15 3-Pin .100" Header Backbox Light
CN16 4-Pin .100" Header 3.3v / 5v / 12v
CN17 ETHERNET ETHERNET connector
CN21 SATA Header SATA connector
CN22 RJ45 SPIKE node bus - to playfield node
CN25 12-Pin .100" Header Dedicated switch inputs - service, volume
switches
James Bond Indicia © 1962-2022 Danjaq LLC and Metro-Goldwyn-Mayer Studios Inc. All Rights Reserved.
Input Input Wire GND Ground Wire
Pin Pin
- - - -
- - - -
- - - -
- - - -
- - - -
- - - -
- - - -
- - - -
1 LGN-GRY 11 BLK-WHT
2 LGN-VIO 11 BLK-WHT
3 LGN-BLU 11 BLK-WHT
4 LGN-BLK 11 BLK-WHT
JAMES BOND 007 LE / PREMIUM MANUAL 500-55V2-01
ELECTRONIC PINOUTS AND SCHEMATICS
Location Type
CPU Node
CPU Node
CPU Node
CPU Node
CPU Node
CPU Node
CPU Node
CPU Node
Coin Door
Coin Door
Coin Door
Coin Door
COMPONENTS
ID Name
S1 DIP Switches
S2 Reset Switch
SD CARD (CN13) For system SD card. Note: only to be removed if instructed to by
Stern Service.
BT1 BR1225 3V Lithium battery for game clock between power cycles
STATUS LEDS
LED ID Name Color Description
48V +48V Supply In Red ON: Main system power is connected.
OFF: No 48V system power. Check power supply
connections, cables, and fuses.
3.3V +3.3V Logic Red ON: Logic power supply is good.
OFF: Logic power supply bad, call tech support.
5V +5V Logic Red ON: Logic power supply is good.
OFF: Logic power supply bad, call tech support.
12V +12V Backbox Red ON: Back box LED power good.
Illumination OFF: Backbox LED power bad, call tech support.
VA +30V Audio Red ON: Audio power supply is good.
OFF: Audio power supply off, call tech support.
VNB +9V Node Bus Red Power for the Node bus. ON: Power for node
bus good.
OFF: Power to node bus not detected, call tech
support.
5V (CPU) +5V Logic Red ON: Logic power supply is good.
OFF: Logic power supply bad, call tech support.
SDIO ACT Not Used Red Should remain unlit as it is not currently used.
STATUS CPU Heartbeat, Red Double blink ~1/2 second: Good, Processor
System Status running.
OFF: Processor not running, call tech support.
μSD ACT Activity indicator Red Should blink rapidly when reading or writing to
for micro SD Card micro SD card.
D23 Netbridge Status Red Should blink once every ~1/2 second.
Address Part Number
0-SW-0 -
0-SW-1 -
0-SW-2 -
0-SW-3 -
0-SW-4 -
0-SW-5 -
0-SW-6 -
0-SW-7 -
0-SW-9 180-5192-04
0-SW-10 180-5192-02
0-SW-11 180-5192-02
0-SW-12 180-5192-00
23