Delta Elektronika SM3300 Series Product Manual
  1. Manuals
  2. Brands
  3. Delta Elektronika Manuals
  4. Power Supply
  5. SM3300 Series
  6. Product manual

Delta Elektronika SM3300 Series Product Manual

Hide thumbs Also See for SM3300 Series:
Table of Contents

Advertisement

Quick Links

DELTA ELEKTRONIKA B.V.
DC POWER SUPPLIES
SM3300 - Interfaces
 INT MOD M/S
 INT MOD SIM
 INT MOD CON
 INT MOD SER
 INT MOD DIG
 INT MOD ANA
Firmware Update
It is strongly recommended, first to perform a firmware update before further
operation. Download the SM3300 Quick Start Manual for instructions.
Driver & Example Software
For several applications and Interfaces there is Driver & Example Software
available on our website. See PRODUCTS\SM3300\DOWNLOADS.
PRODUCT MANUAL
Firmware version P0157
Contents:
1 –
Safety Instructions
2 –
Sicherheitsanweisungen
3 –
Master Slave Interface
4 –
Simulation Interface
5 –
Isolated Contacts
6 –
Serial Interface
7 –
Digital (User) I/O
8 –
Isolated Analog Interface
1 / 21
DELTA ELEKTRONIKA B.V.
Vissersdijk 4, 4301 ND
www.DeltaPowerSupplies.com
Zierikzee, the Netherlands
Tel. +31 111 413656
rev. Jan. 2020

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SM3300 Series and is the answer not in the manual?

Questions and answers

Related Manuals for Delta Elektronika SM3300 Series

Summary of Contents for Delta Elektronika SM3300 Series

  • Page 1 DELTA ELEKTRONIKA B.V. Vissersdijk 4, 4301 ND www.DeltaPowerSupplies.com Zierikzee, the Netherlands Tel. +31 111 413656 DC POWER SUPPLIES SM3300 - Interfaces  INT MOD M/S  INT MOD SIM  INT MOD CON  INT MOD SER  INT MOD DIG ...
  • Page 2 Failure to comply with the safety precautions or warnings in this document violates safety standards of design, manufacture and intended use of this equipment and may impair the built-in protections. Delta Elektronika shall not be liable for user’s failure to comply with these requirements.
  • Page 3 Unscrew the screws and remove the cover(s).  Always place the cover(s) back before connecting the unit to the mains supply again. 1.12 Environmental Conditions The Delta Elektronika power supplies safety approval applies to the following operating conditions:  Indoor use ...
  • Page 4 Die Nichteinhaltung der Sicherheitsvorkehrungen oder Warnungen in diesem Dokument verstößt gegen die Sicherheitsstandards im Hinblick auf Bauart, Produktion und vorgesehene Nutzung dieses Geräts und kann die eingebauten Schutzvorrichtungen beschädigen. Delta Elektronika haftet nicht dafür, wenn der Nutzer diesen Anforderungen nicht nachkommt.
  • Page 5 SM3300 INTERFACES 2.10 Teileaustausch & Modifikationen Teileaustausch und Modifikationen sind ausschließlich autorisiertem Delta Elektronika-Service-Personal gestattet. Reparaturen oder Modifikationen am Gerät dürfen nur durch eine Delta Elektronika-Serviceeinrichtung durchgeführt werden. 2.11 Entfernung von (Sicherheits-) Abdeckungen Sicherheitsabdeckung(en) werden verwendet, um potenziell gefährliche Spannungen abzudecken. Beachten Sie Folgendes, wenn Sie die Sicherheitsabdeckung(en) entfernen: ...
  • Page 6 UNIT CONFIGURATION  The unit will automatically detect the new inserted interface.  The interface icon will be shown in the display, see fig 3 - 3.  Configuring of slaves: 6 / 21 DELTA ELEKTRONIKA B.V. rev. Jan. 2020...

  • Page 7: Troubleshooting

     Check the web interface for errors in one of the devices.  Use Ethernet commands to check for errors in the master slave system. CALIBRATION  Calibration of the interface is not applicable. 7 / 21 DELTA ELEKTRONIKA B.V. rev. Jan. 2020...
  • Page 8 For example the interface is assembled in slot2. To program the CV-settings via this interface, via the front menu go to CONFIGURATION -> SOURCE -> Vsettings and set it to Slot2. 8 / 21 DELTA ELEKTRONIKA B.V. rev. Jan. 2020...
  • Page 9 ‘Load’. When you accept the following dialog, the parameters table 4 - 3 from the simulation module are filled in the application. 9 / 21 DELTA ELEKTRONIKA B.V. rev. Jan. 2020...
  • Page 10  All these operating modes are limited by the maximum configurable resistance as specified.  The settings for the leadless sensing simulation can be configured trough the web interface. Within the interfaces page. 10 / 21 DELTA ELEKTRONIKA B.V. rev. Jan. 2020...
  • Page 11 4.12.3 INTERFACE DOES NOT CORRECT THE OUTPUT VOLTAGE OR CURRENT  Check if the simulation type is enabled.  Check the simulation interface settings. 11 / 21 DELTA ELEKTRONIKA B.V. rev. Jan. 2020...
  • Page 12  The unit will automatically detect the new inserted interface. fig 5 - 3  The interface icon will be shown in the display, see fig 5 - 3. Position of the interface icon in the unit display. 12 / 21 DELTA ELEKTRONIKA B.V. rev. Jan. 2020...
  • Page 13  Check Interlock / enable connection on CON K. CALIBRATION fig 5 - 7  Calibration of the interface is not applicable. 15 - 30 V Enable. fig 5 - 8 Interlock contact (door switch). 13 / 21 DELTA ELEKTRONIKA B.V. rev. Jan. 2020...

  • Page 14: Serial Interface

    Pin connections of the RS422 / RS485 connector.  Connect the mains supply again and check all the safety covers are installed.  Switch on the unit.  The LED should light up. 14 / 21 DELTA ELEKTRONIKA B.V. rev. Jan. 2020...

  • Page 15: Unit Configuration

     Check that the communication is working; "*IDN?" must return Available serial programming commands. a value. Ensure to end the query with the termination character LF.  (LF = 0x0Ah in ASCII) 15 / 21 DELTA ELEKTRONIKA B.V. rev. Jan. 2020...
  • Page 16  Port settings on the PC. o Baudrate : bps 9600 o Data bits : 8 o Parity bits : None o Stop bits : 1 o Flow control : None 16 / 21 DELTA ELEKTRONIKA B.V. rev. Jan. 2020...
  • Page 17  The LED indicated in fig. 7 - 2 will light up. UNIT CONFIGURATION  The unit will automatically detect the new inserted interface.  The interface icon will be shown in the display, see fig 7 - 3. 17 / 21 DELTA ELEKTRONIKA B.V. rev. Jan. 2020...

  • Page 18: Inputs And Outputs

    Sequencer to make the power supply act like a Power PLC.  Refer to the Delta Elektronika programming manual for Ethernet (section 6) & Sequencer (section 7) for commands.  The manual is stored inside every SM3300 unit and can be downloaded via the web interface.

  • Page 19: Isolated Analog Interface

     The pinning of the INT MOD ANA is similar to other Delta Elektronika power supplies, see fig 8 - 2.  Connect the mains supply again and check all the safety covers are installed.  Switch on the unit. 19 / 21 DELTA ELEKTRONIKA B.V. rev. Jan. 2020...

  • Page 20: Analog Programming

     The table in the interface datasheet shows the impedance levels of the monitoring outputs.  The monitoring outputs can drive a meter directly (fig. 8 - fig 8 - 7 Remote control. 20 / 21 DELTA ELEKTRONIKA B.V. rev. Jan. 2020...

  • Page 21: Status Signals

     The isolated analog interface is factory calibrated.  If desired, both the 5 V and 10 V range can be custom calibrated. See the ethernet programming manual for more details. 21 / 21 DELTA ELEKTRONIKA B.V. rev. Jan. 2020...

This manual is also suitable for:

Int mod m/sInt mod simInt mod conInt mod serInt mod digInt mod ana

Table of Contents