Table of Contents
Advertisement
Quick Links
Please note that Cypress is an Infineon Technologies Company.
The document following this cover page is marked as "Cypress" document as this is the
company that originally developed the product. Please note that Infineon will continue
to offer the product to new and existing customers as part of the Infineon product
portfolio.
Continuity of document content
The fact that Infineon offers the following product as part of the Infineon product
portfolio does not lead to any changes to this document. Future revisions will occur
when appropriate, and any changes will be set out on the document history page.
Continuity of ordering part numbers
Infineon continues to support existing part numbers. Please continue to use the
ordering part numbers listed in the datasheet for ordering.
www.infineon.com
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Cypress MB2100-01A-E
Summary of Contents for Cypress MB2100-01A-E
- Page 1 Please note that Cypress is an Infineon Technologies Company. The document following this cover page is marked as “Cypress” document as this is the company that originally developed the product. Please note that Infineon will continue to offer the product to new and existing customers as part of the Infineon product portfolio.
- Page 2 MB2100-01A-E Single Port Embedded Emulator Debugger SPEED-BOX Operation Guide Doc. # 002-05542 Rev. *A Cypress Semiconductor 198 Champion Court San Jose, CA 95134-1709 Phone (USA): 800.858.1810 Phone (Intnl): +1.408.943.2600 www.cypress.com...
- Page 3 Cypress is not liable, in whole or in part, and you shall and hereby do release Cypress from any claim, damage, or other liability arising from or related to all Unintended Uses of Cypress products.
- Page 4 Warranty and Liability Disclaimers ■ The specifications of the product are subject to change without notice. Cypress assumes no liability for any loss or damage whatsoever directly or indirectly arising out of the use of the product. Related manuals ■...
- Page 5 Please confirm the latest relevant information with the sales representatives. RealTime OS ■ This product uses the mT-Kernel source code under the mT-License of the T-Engine forum (www.t-engine.org). MB2100-01A-E Single Port Embedded Emulator Debugger SPEED-BOX Operation Guide, Doc. # 002-05542 Rev. *A...
- Page 6 It is recommended that it be stored in the original packaging. Transporting the prod- Damage uct may cause a damage or fault. Therefore, keep the packaging materials and use them when re-shipping the product. MB2100-01A-E Single Port Embedded Emulator Debugger SPEED-BOX Operation Guide, Doc. # 002-05542 Rev. *A...
-
Page 7: Table Of Contents
4. User System Board Design Guidelines Circuit board design rules ..................21 Handling the coaxial cable when using a general purpose connector .......23 5. Cautions 6. Major Changes Revision History MB2100-01A-E Single Port Embedded Emulator Debugger SPEED-BOX Operation Guide, Doc. # 002-05542 Rev. *A... -
Page 8: Product Description
■ Operation manual (Japanese version) ■ Note: This product is available upon request. To request the product, please contact Cypress Sales for more information. For additional information, please visit our website: www.cypress.com/contact-us. MB2100-01A-E Single Port Embedded Emulator Debugger SPEED-BOX Operation Guide, Doc. # 002-05542 Rev. *A... -
Page 9: Appearance And Part Names
EXTRA LED Do not use. POWER switch Turns the power to the SPEED-BOX on and off. USB connector Connects to the host computer using a USB cable. MB2100-01A-E Single Port Embedded Emulator Debugger SPEED-BOX Operation Guide, Doc. # 002-05542 Rev. *A... -
Page 10: Optional Parts
See Section “1.4: Debug interface cable” for details on the specifications of the debug interface cable. MB2100-01A-E Single Port Embedded Emulator Debugger SPEED-BOX Operation Guide, Doc. # 002-05542 Rev. *A... -
Page 11: Debug Interface Cable
The communication speeds that can be configured are limited by the MCU clock frequency. See the hardware manual of the MCU for details on the parameters. MB2100-01A-E Single Port Embedded Emulator Debugger SPEED-BOX Operation Guide, Doc. # 002-05542 Rev. *A... -
Page 12: Coupling Connectors
2 or more cables are connected together is given by Table 1-3. Table 1-4 shows the part number and manufacturer name of a coupler that has been verified by Cypress. Figure 1-2 shows the method for connecting a coupler. -
Page 13: Small Form Connectors
The operation of this connector has been verified by Cypress. Take care because the relationship between the cable length and maximum permissible communication speed applies regardless of the cable specifications. -
Page 14: Specifications
*: This device isolates the power supply system of the host computer from the user system. See the Section "Power supply isolation specifications" below for details on the power supply isolation. MB2100-01A-E Single Port Embedded Emulator Debugger SPEED-BOX Operation Guide, Doc. # 002-05542 Rev. *A... -
Page 15: Usb Circuit Specifications
The withstand voltage of the insulation (the tolerable potential difference between the host computer SG and the user system SG) is AC250V / DC250V for constantly applied voltages. Figure 1-4 shows the relationship between the SG/FG and the isolation. MB2100-01A-E Single Port Embedded Emulator Debugger SPEED-BOX Operation Guide, Doc. # 002-05542 Rev. *A... -
Page 16: Power Supply Isolation Specifications
Product Description Figure 1-4. Relationship between SG/FG and isolation Host User system SPEED-BOX computer Isolator In this case, power supply isolation is required MB2100-01A-E Single Port Embedded Emulator Debugger SPEED-BOX Operation Guide, Doc. # 002-05542 Rev. *A... -
Page 17: Connecting The Speed-Box
(2)Mini USB cable Commercially available mini USB cables can also be used. When using a commercial product, use a cable that has been certified for USB 2.0. MB2100-01A-E Single Port Embedded Emulator Debugger SPEED-BOX Operation Guide, Doc. # 002-05542 Rev. *A... -
Page 18: Connecting The Speed-Box To The User System
Note: If there is an electromotive force between the SG and FG on the user system, hot plug operations are forbidden because of the risk of electrical shock. MB2100-01A-E Single Port Embedded Emulator Debugger SPEED-BOX Operation Guide, Doc. # 002-05542 Rev. *A... -
Page 19: Connecting The Speed-Box To The Host Computer
As a general rule, it is recommended that the SPEED-BOX power switch be turned on after connecting the USB cable. However, the equipment will not be damaged if the USB cable is disconnected or connected while the power switch is on. MB2100-01A-E Single Port Embedded Emulator Debugger SPEED-BOX Operation Guide, Doc. # 002-05542 Rev. *A... -
Page 20: Operating Procedures
Figure 3-1. Dialog box display 6. Press the [OK] button on the dialog shown above after the power-on reset of the user system has been released. MB2100-01A-E Single Port Embedded Emulator Debugger SPEED-BOX Operation Guide, Doc. # 002-05542 Rev. *A... - Page 21 1. Select [Debug] -> [End Debugging] in SOFTUNE Workbench to end the debugger connection (the MDI bus is deactivated). 2. Disconnect the power supply of the target board. 3. Disconnect the power supply of the SPEED-BOX. MB2100-01A-E Single Port Embedded Emulator Debugger SPEED-BOX Operation Guide, Doc. # 002-05542 Rev. *A...
-
Page 22: User System Board Design Guidelines
MCU you are using. Figure 4-1. Schematic diagram of the circuit near the MCU MDI pin User system MCU V CN: MDI connector (DEBUG I/F) MB2100-01A-E Single Port Embedded Emulator Debugger SPEED-BOX Operation Guide, Doc. # 002-05542 Rev. *A... - Page 23 L1 and L2 noise In areas that run parallel, create as large a gap as possible to fully Mandatory protection 2 reduce cross-talk from the parallel signal. MB2100-01A-E Single Port Embedded Emulator Debugger SPEED-BOX Operation Guide, Doc. # 002-05542 Rev. *A...
-
Page 24: Handling The Coaxial Cable When Using A General Purpose Connector
Figure 4-2. Handling the coaxial cable General-purpose connector Coaxial cable (non-coaxial cable) Coaxial cable User system General purpose parallel cable General purpose connector Second connector (general-purpose or coaxial) MB2100-01A-E Single Port Embedded Emulator Debugger SPEED-BOX Operation Guide, Doc. # 002-05542 Rev. *A... -
Page 25: Cautions
Although all of the Cypress recommended parts support hot plugging, check the condition of the connector, such as whether there are assembly problems, before carrying out hot plugging. MB2100-01A-E Single Port Embedded Emulator Debugger SPEED-BOX Operation Guide, Doc. # 002-05542 Rev. *A... -
Page 26: Major Changes
Changed the description Deleted a part of the description of Item "MDI bus maximum Table 6 communication speed" Note: Please see “Revision History” about later revised information. MB2100-01A-E Single Port Embedded Emulator Debugger SPEED-BOX Operation Guide, Doc. # 002-05542 Rev. *A... -
Page 27: Revision History
Origin of Revision ECN# Issue Date Description of Change Change 08/10/2015 GSHI Initial release Migrated Spansion Guide from MB2100-01A-E_SS01-00026-4E to 5272741 08/08/2016 GSHI Cypress format. MB2100-01A-E Single Port Embedded Emulator Debugger SPEED-BOX Operation Guide, Doc. # 002-05542 Rev. *A...
Need help?
Do you have a question about the MB2100-01A-E and is the answer not in the manual?
Questions and answers