Page 1
To prevent potential injury and to avoid unnecessary service calls, read this manual carefully and completely. PLEASE KEEP THIS MANUAL FOR FUTURE REFERENCE Hayward Pool Products (Australia) Pty Ltd. Melbourne-Sydney-Brisbane-Perth Email: sales@hayward-pool.com.au | Website: www.hayward-pool.com.au PO Box 4384 | Dandenong South VIC 3164...
WARNING – Use only genuine Hayward replacement parts. WARNING – If the power supply cord is damaged the device must not be used. The power supply cord must be replaced by the manufacturer or similarly qualified persons to avoid any danger.
The AquaRite+ is suitable for treating most size residential pools up to 150,000 litres in a cool climate and depending which size Hayward Turbo Cell is connected to the unit. NOTE: Before installing this product as part of a salt water purification system in a pool or spa using natural stone for coping or for immediately adjacent patios/decking, a qualified stone installation specialist should be consulted regarding the appropriate type, installation, sealant (if any) and maintenance of stone used around a saline pool with an electronic chlorine generator in your particular location and circumstances.
Page 4
Acid Addition • Filter Pump Vista Pool App, allowing the user to remotely on/off • Light on/off control the pool/spa system with a phone or tablet. AquaRite+ as a Universal Controller ® USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Page 4...
Page 5
Check Switch Switch Valve Cell Position 1 Position 2 Back to Pool Return Pipe IMPORTANT: There must be at least a 30 cm straight pipe run before (upstream) the Flow Switch. ® USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Page 5...
Page 6
® USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Page 6...
Page 7
Pull Unscrew Dead Front Panel: Remove the six (6) screws fastening the panel to the unit. Once all loose, lift the panel off the unit to access the PCB. Unscrew Unscrew ® USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Page 7...
CAUTION - This circuit must be protected by a residual current device (RCD) with a fixed residual ________ operating current not exceeding 30 mA. CAUTION - Hayward recommends that a Lightning Surge Protector Device (SPD) is installed on the ________ feed circuit to the AQR+ by a qualified electrical contractor in accordance with AS/NZS ________ 3000 Australian Wiring Rules latest edition.
Auxiliary dry contact (or heating control). 9 - 10 Dry contact If no heating system is installed on Aux 4, it can be used as another auxiliary contact. To do this, contact Hayward technical support. Description of Inputs Name Description...
Page 10
200 W (10 Amp maximum with filter pump plugged into power control socket) Ingress Progression IPX 3 Pump Power Socket Outlet 240 V a.c. 7 Amps Maximum Load Dimensions 270 x 220 x 150 ® USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Page 10...
To remove salt, drain the pool down and replenish with fresh water. Repeat until the desired level is achieved. Do not add stabiliser to indoor pools. ® USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Page 11...
Page 12
Quantity of Stabiliser (CYANURIC ACID in kg) Required for 40 ppm Volume of water in the pool in Litres (L) Current Stabiliser 30,000 37,500 45,000 52,500 60,000 67,500 75,000 82,500 90,000 97,500 105,000 112,500 120,000 127,500 135,000 142,500 150,000 Level (ppm) ® USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Page 12...
The water must be balanced manually BEFORE the device is started up. The following table summarises the ideal chemical levels recommended by Hayward. Your water should be checked regularly to maintain these ideal levels in order to minimise surface corrosion, scaling or deterioration and to ensure maximum performance from your AquaRite+ Chlorinator.
Password: Protects access to the user menu by (Note - The Network tab only appears if the activating a password. Optional safety feature, Hayward Wi-Fi Module is connected.) necessity determined by user discretion. To enter Settings: date and time. your password, press a 5-key combination to be Settings: screen lighting intensity (0-100%) and memorised by the system.
Page 15
Adjustable between 0 - 30 g/hr. Refer to page 10 for cell specifications SPA: SPA settings activation. (The installation of the Hayward Spa Flow Switch During the boost period, redox (ORP) control (option) can be deactivated. Upgrade Kit is required to use this feature)
Page 16
AQR+ select between speeds V1, V2, or V3 on menu. Hayward variable the motor drive. When the AQR+ is configured to control a Hayward Variable Enter the password: Speed Pump, the power socket is disabled and the pump needs to be permantly + - OK powered from a regular GPO.
» Check that the system automatically changes polarity (see display). White Flakes in the Pool » This occurs when the water is unbalanced and very hard. » Balance the water, check the cell and clean it, if necessary. ® USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Page 17...
Page 18
This should only be done in severe cases where flushing with water will not remove most of the deposits. To acid wash, turn off the main power supply to the AquaRite+ and remove pressure from the plumbing system before removing the T-Cell. This procedure uses a Hayward T-Cell Cleaning Stand (PN: GLX-CELLSTAND).
LIMITED WARRANTY Hayward Pool Products (Australia) warrants that its products are free from defects in materials and manufacture for 12 months from date of supply by Hayward Pool Products (Australia) plus 90 days to allow for installation and supply (unless otherwise specified). Hayward Pool...
Page 20
Hayward Pool Products (Australia) Pty Ltd. Melbourne-Sydney-Brisbane-Perth Email: sales@hayward-pool.com.au | Website: www.hayward-pool.com.au PO Box 4384 | Dandenong South VIC 3164 ABN 66 083 413 414 Sales Contact Ph: 1300POOLS1 Fax: 1300POOLS2 Hayward and AquaRite are registered trademarks of Hayward Industries, Inc.