Related Manuals for Kontron KBox F-300-V1K
Summary of Contents for Kontron KBox F-300-V1K
- Page 1 USER GUIDE KBox F-300-V1K Doc. User Guide, Rev. 1.0 Doc. ID: [To be Determined] www.kontron.com...
- Page 2 KBox F-300-V1K - User Guide, Rev. 1.0 This page has been intentionally left blank www.kontron.com // 2...
- Page 3 In cases of doubt, please contact Kontron. This user guide is protected by copyright. All rights are reserved by Kontron. No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means (electronic, mechanical, photocopying, recording, or otherwise), without the express written permission of Kontron.
- Page 4 ENVIRONMENTAL DAMAGE (COLLECTIVELY, "HIGH RISK APPLICATIONS"). You understand and agree that your use of Kontron devices as a component in High Risk Applications is entirely at your risk. To minimize the risks associated with your products and applications, you should provide adequate design and operating safeguards.
- Page 5 If you have any difficulties using this user guide, discover an error, or just want to provide some feedback, contact Kontron support. Detail any errors you find. We will correct the errors or problems as soon as possible and post the revised user guide on our website.
-
Page 6: Symbols
KBox F-300-V1K - User Guide, Rev. 1.0 Symbols The following symbols may be used in this user guide DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury. WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury. -
Page 7: For Your Safety
Therefore, in the interest of your own safety and of the correct operation of your new Kontron product, you are requested to conform with the following guidelines. -
Page 8: Lithium Battery Precautions
General Instructions on Usage In order to maintain Kontron’s product warranty, this product must not be altered or modified in any way. Changes or modifications to the product, that are not explicitly approved by Kontron and described in this user guide or received from Kontron Support as a special handling instruction, will void your warranty. -
Page 9: Table Of Contents
KBox F-300-V1K - User Guide, Rev. 1.0 Table of Contents Symbols ..........................................6 For Your Safety ........................................7 High Voltage Safety Instructions .................................. 7 Special Handling and Unpacking Instruction ............................7 Lithium Battery Precautions ..................................8 General Instructions on Usage ..................................8 Quality and Environmental Management .............................. - Page 10 KBox F-300-V1K - User Guide, Rev. 1.0 4.3.6. Mic-In ........................................25 4.3.7. S/PDIF ........................................25 4.3.8. GbE LAN ........................................25 4.3.9. USB 3.1 ........................................25 4.3.10. USB 2.0 ........................................26 4.4. Left I/O Panel......................................27 4.4.1. Micro SIM Card Cage .................................... 27 4.5.
-
Page 11: List Of Tables
Figure 6: Internal View - - Back side of the top access cover ......................29 Figure 7: Internal View - - Bottom Side (without cover) ........................30 Figure 8: Descrewing the top access cover of the KBox F-300-V1K ....................32 Figure 9: Disengaging the top access cover ............................32 Figure 10: Descrewing the bottom access cover .......................... - Page 12 KBox F-300-V1K - User Guide, Rev. 1.0 Figure 17: BIOS Main Menu Screen System Data and Time ....................... 55 Figure 18: BIOS Main Menu Screen - - AMD Firmware Version ......................56 Figure 19: BIOS Advanced Menu.................................. 58 Figure 20: BIOS Advanced Menu - Display Configuration ........................59 Figure 21: BIOS Advanced Menu - - CPU Chipset Configuration ......................
-
Page 13: 1/ General Safety Instructions For It Equipment
Kontron is exempt from accident liability, this also applies during the warranty period. The product has been built and tested according to the basic safety requirements for low voltage (LVD) applications and has left the manufacturer in safety-related, flawless condition. - Page 14 KBox F-300-V1K - User Guide, Rev. 1.0 Additional safety instructions for DC power supply circuits To guarantee safe operation of devices with DC power supply voltages larger than 60 volts DC or a power consumption larger than 240 VA, please observe that: the device is set up, installed and operated in a room or enclosure marked with ‘‘RESTRICTED ACCESS’’, if...
-
Page 15: Electrostatic Discharge (Esd)
KBox F-300-V1K - User Guide, Rev. 1.0 1.1. Electrostatic Discharge (ESD) A sudden discharge of electrostatic electricity can destroy static-sensitive devices or micro-circuitry. Therefore proper packaging and grounding techniques are necessary precautions to prevent damage. Always take the following precautions: 1. - Page 16 KBox F-300-V1K - User Guide, Rev. 1.0 Do not dispose of lithium batteries in general trash collection. Dispose of the battery according to the local regulations dealing with the disposal of these special materials, (e.g. to the collecting points for dispose of batteries).
-
Page 17: 2/ Electromagnetic Compatibility
Consult the dealer or an experienced radio/TV technician for help. Kontron is not responsible for any radio television interference caused by unauthorized modifications of this equipment or the substitution or attachment of connecting cables and equipment other than those specified by Kontron. -
Page 18: 3/ Shipment And Unpacking
6. If you notice any shipping damage or inconsistencies between the contents and your order, please contact Kontron for help and information. 3.2. Scope of Delivery 3.2.1. Standard 1x KBox F-300-V1K (corresponding to the ordered system configuration) 1x Power Adapter 1x Power cord (plug type depending on country) ... -
Page 19: 4/ System Overview
KBox F-300-V1K - User Guide, Rev. 1.0 4/ System Overview The KBox F-300-V1K is an embedded system enclosed within a compact chassis, offering excellent processing and graphics performance. It can be optionally factory-equipped with an mPCIe WLAN / Bluetooth card and / or M.2 Key B WWAN card for four antennas. - Page 20 KBox F-300-V1K - User Guide, Rev. 1.0 To provide sufficient heat dissipation by the cooling of the device, do not cover the ventilation slots of the KBox F-300-V1K. Do not place any objects on the device. When installing the system, please keep clearance for air circulation.
-
Page 21: System Expansion Capabilities
4.1. System Expansion Capabilities 4.1.1. System Expansion via SATA Interface The KBox F-300-V1K comes with a 15+7-pin SATA power / data cable connector. This interface is SATA 3.0 compatible. Users can expand the system with a 2.5" SATA HDD / SSD drive. -
Page 22: Front I/O Panel
KBox F-300-V1K - User Guide, Rev. 1.0 4.2. Front I/O Panel Figure 1: Front I/O Panel 1 Power Switch (see Chapter 4.2.1) 2 Power LED (see Chapter 4.2.2) 3 Storage LED (see Chapter 4.2.3) 4 USB 2.0 (see Chapter 4.2.4) 5 RS232/422/485 (see Chapter 4.2.5) -
Page 23: Storage Led
The storage LED blinks red when data is being written into or read from the HDD / SSD drive. 4.2.4. USB 2.0 The KBox F-300-V1K provides two USB 2.0 / 1.1 interfaces on the front I/O panel. These connectors allow connection of USB-compatible devices to the system. -
Page 24: Rear I/O Panel
KBox F-300-V1K - User Guide, Rev. 1.0 4.3. Rear I/O Panel Figure 2: Rear I/O Panel 1 DC-In (see Chapter 4.3.1) 2 DP++ (see Chapter 4.3.2) 3 DP (see Chapter 4.3.3) 4 Line-In (see Chapter 4.3.4) 5 Line-Out (see Chapter 4.3.5) 6 Mic-In (see Chapter 4.3.6) -
Page 25: Line-In
Steady Green - Link is up, no activity Off - 10 Mbit/s link established 4.3.9. USB 3.1 The KBox F-300-V1K provides two USB 3.1 / 2.0 interfaces. These connectors allow connection of USB 3.1, USB 3.0 or USB 2.0 compatible device to the system. www.kontron.com... -
Page 26: Usb 2.0
KBox F-300-V1K - User Guide, Rev. 1.0 4.3.10. USB 2.0 The KBox F-300-V1K provides two USB 2.0 / 1.1 interfaces. These connectors allow connection of USB-compatible devices to the system. www.kontron.com // 26... -
Page 27: Left I/O Panel
KBox F-300-V1K - User Guide, Rev. 1.0 4.4. Left I/O Panel Figure 4: Left I/O Panel 1 Micro SIM Card Cage (see Chapter 4.4.1) 4.4.1. Micro SIM Card Cage The push-push type micro SIM card cage is used to host a micro SIM card to access a WWAN network for data communication. -
Page 28: Internal View - - Top Side
6 M.2 fixing bolt for Key B type 2242 7 M.2 fixing bolt for Key B type 2280 4.5.1. DDR4 SO-DIMM Memory Socket The KBox F-300-V1K provides two 260-pin DDR4 SO-DIMM sockets (Figure 5, pos. 1) to install memory RAMs. www.kontron.com // 28... -
Page 29: Sata Power / Data Cable Connector
WLAN or WLAN + Bluetooth combo card. 4.5.4. M.2 Key B Socket The KBox F-300-V1K reserves one M.2 Key B socket (Figure 5, pos. 4), allowing the expansion with a Type 22x42 or Type 22x80 M.2 WWAN module or M.2 SSD drive. -
Page 30: Internal View - - Bottom Side
1 M.2 Key M Socket (M2M2, see Chapter 4.6.1) 2 M.2 fixing bolt for Key M type 2280 4.6.1. M.2 Key M Socket The KBox F-300-V1K reserves one M.2 Key M socket (Figure 7, pos. 1), allowing the expansion with a Type 22x80 M.2 SSD drive. www.kontron.com... -
Page 31: 5/ Accessing Internal Components
KBox F-300-V1K - User Guide, Rev. 1.0 5/ Accessing Internal Components This section contains important information that you must read before accessing the internal components. You must follow these procedures properly when installing, removing or handling any board. It is recommended to expand your system with applicable expansion card(s) before it is installed into an equipment, machine or cabinet. -
Page 32: Opening And Closing The Chassis
To access DDR4 SO-DIMM, SATA, mPCIe and M.2 Key B slots / sockets / connectors 2. The KBox F-300-V1K should lay on a flat, clean surface with the top side facing upwards. 3. Loosen and remove the Phillips screws (two located on the top side of the chassis), that secure the top access cover to the chassis. -
Page 33: Figure 10: Descrewing The Bottom Access Cover
To access M.2 Key M socket 9. The KBox F-300-V1K should lay on a flat, clean surface with the bottom access cover facing upwards. 10. Loosen and remove the Phillips screws (four located on the bottom access cover), that secure the bottom access cover to the chassis. -
Page 34: Installing So-Dimm Memory Module(S)
14. Tighten the retained screws when the cover is firmly in place. When used as intended, the KBox F-300-V1K is to operate only in closed condition. Only when the access covers are properly fixed with the screws and the front side with... -
Page 35: Installing An M.2 Key B Ssd / Expansion Card
KBox F-300-V1K - User Guide, Rev. 1.0 1. Open the device as described in the subsection 5.1 "Opening and Closing the Chassis" (step 1-6). 2. Locate the mPCIe socket (MPCIE1) (Figure 5, pos. 3) and the corresponding fixing bolt (Figure 5, pos. 5). -
Page 36: 6/ Thermal Considerations
There are ventilation meshes located on the right, left and top sides of the KBox F- 300-V1K. They provides heat dissipation during operation. To provide sufficient heat dissipation for the cooling of the KBox F-300-V1K, never cover the ventilation meshes of the chassis. Do not place any objects on the device. - Page 37 KBox F-300-V1K - User Guide, Rev. 1.0 When the KBox F-300-V1K is extended and configured with third party components like mPCIe / M.2 expansion card(s) and hard drives (HDD or SSD), it has to be taken into account that the air temperature inside the system is higher than the ambient temperature.
-
Page 38: 7/ Installation Instructions
Refer also to section 10.1.2 ‘‘Mechanical Specifications’’. The KBox F-300-V1K must be firmly attached to a clean flat and solid mounting surface. Use proper fastening materials suitable for the mounting surface. Ensure that the mounting surface type and the used mounting solution safely support the load of the KBox F-300-V1K and the attached components. -
Page 39: System Mounting
(Figure 11). The kit consists of two parts: a base bracket (Figure 11, pos. 1) to be fixed permanently on the mounting surface and another hooked bracket to hold the KBox F-300-V1K with a hand-screw knob (Figure 11, pos. 2) to secure two brackets. -
Page 40: Figure 13: Securing The Base Mounting Bracket
Figure 13: Securing the base mounting bracket 3. Secure the hooked mounting bracket onto the bottom side of the KBox F-300-V1K (Figure 14) with M3 screws (6 mm long) via the VESA 75 mounting holesvia the VESA 75 mounting holes. The orientation depends on applications. - Page 41 KBox F-300-V1K - User Guide, Rev. 1.0 For a sufficient air circulation around the device, we recommend keep a proper clearance and not mount / operate any other devices within the clearance around the KBox F-300- V1K. www.kontron.com // 41...
-
Page 42: Dc Power Connection
The KBox F-300-V1K is connected by a DC power input jack (Figure 2, pos. 1) to a DC power source. The KBox F-300-V1K is delivered with a power adapter to convert AC voltage into DC 12 V and a power cord to carry AC power to the power adapter. -
Page 43: 8/ Start Up
8.1. Connecting to DC Power Supply The DC power input jack (Figure 2, pos. 1) is located on the rear side of the KBox F-300-V1K. The KBox F-300-V1K will be connected to a AC-to-DC power adapter via the attached male DC power plug and corresponding power cable to couple together the adapter and the AC power outlet. -
Page 44: Operating System And Hardware Component Drivers
If you have ordered the KBox F-300-V1K without a pre-installed operating system, you will need to install the operating system and the appropriate drivers for the system configuration you have ordered (optional hardware components) yourself. -
Page 45: 9/ Maintenance And Cleaning
9/ Maintenance and Cleaning Equipment from Kontron requires only minimum servicing and maintenance for proper operation. For light soiling, clean the KBox F-300-V1K with a dry cloth. Carefully remove dust from the surface of the chassis using a clean, soft brush. ... -
Page 46: Technical Specifications
KBox F-300-V1K - User Guide, Rev. 1.0 Technical Specifications Table 1: Technical Specifications System Processor AMD Ryzen™ V1000 Series Processors Memory 2x DDR4 SO-DIMM Video Display Interface 2x DP++ (on rear) 2x DP (on rear) Network Connection Ethernet ... -
Page 47: Mechanical Specifications
KBox F-300-V1K - User Guide, Rev. 1.0 System OS Support Windows 10 10.1. Mechanical Specifications Table 2: Mechanical Specifications Construction Metal Chassis Dimensions (W x D x H) 195 mm x 195 mm x 56 mm / 7.68’’ x 7.68’’ x 2.20’’... -
Page 48: Environmental Conditions
KBox F-300-V1K - User Guide, Rev. 1.0 10.2. Environmental Conditions Table 3: Environmental Conditions Operating Temperature 0 °C ~ 50 °C / 32 °F ~ 122 °F Storage Temperature -20 °C ~ 80 °C / -4 °F ~ 176 °F Humidity ... -
Page 49: 11/ Standard Interfaces
KBox F-300-V1K - User Guide, Rev. 1.0 11/ Standard Interfaces -- - Pin Assignments Low-active signals are indicated by a minus sign. 11.1. DC Power Input Table 5: DC Power Input (see Figure 2, pos. 1) Signal Name DC Jack (female) +12V DC 11.2. -
Page 50: Usb 2.0 Port
KBox F-300-V1K - User Guide, Rev. 1.0 11.4. USB 2.0 Port Table 8: USB 2.0 Port (see Figure 1, pos. 4 & Figure 2, pos. 10) Signal Name 4-pin USB Connector Type A Version 2.0 +USBVCC USB_D- USB_D+ 11.5. DP++ / DP Connector Table 9: DP++ / DP Connector (see Figure 2, pos. -
Page 51: Rs232/422/485 Serial Port
KBox F-300-V1K - User Guide, Rev. 1.0 11.6. RS232/422/485 Serial Port Table 10: RS232/422/485 Serial Port (see Figure 1, pos. 5) RS232 RS422 RS485 Half RS485 Full COM1 ~ COM4 (9-pin D-SUB Male Connector) Duplex Duplex DATA- DATA+ RI / +5V *... -
Page 52: Digital I/O Port
KBox F-300-V1K - User Guide, Rev. 1.0 11.8. Digital I/O Port Table 12: Digital I/O Port (see Figure 1, pos. 7) Signal Name DIO Port (9-pin D-SUB Female Connector) DIO_0 DIO_1 DIO_2 DIO_3 DIO_4 DIO_5 DIO_6 DIO_7 11.9. Line-In Connector Table 13: Line-In Connector (see Figure 2, pos. -
Page 53: 12/ Bios
Supervisor Password (see Security menu), press <RETURN>, and proceed with step 5. 5. A setup menu will appear. The KBox F-300-V1K uEFI BIOS setup program uses a hot key-based navigation system. A hot key legend bar is located on the bottom of the setup screens. -
Page 54: Starting The Uefi Bios
KBox F-300-V1K - User Guide, Rev. 1.0 12.2. Starting the uEFI BIOS The Setup utility features shows six menus in the selection bar at the top of the screen: Main Advanced Power Boot Security ... -
Page 55: Figure 17: Bios Main Menu Screen System Data And Time
KBox F-300-V1K - User Guide, Rev. 1.0 Figure 17: BIOS Main Menu Screen System Data and Time BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit Product Information Product Name KBox F-300 Series BIOS Version KBXF300.100 (x64) BIOS Build Date... -
Page 56: Figure 18: Bios Main Menu Screen - - Amd Firmware Version
KBox F-300-V1K - User Guide, Rev. 1.0 Figure 18: BIOS Main Menu Screen -- - AMD Firmware Version BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit AMD Firmware Version AGESA Version RavenPI-FP5-AM4 1.1.0.A PSP BootLoader Version 0.8.0.6F PSP SecureOS Version 0.8.0.6F... -
Page 57: Advanced Setup Menu
KBox F-300-V1K - User Guide, Rev. 1.0 12.2.2. Advanced Setup Menu The Advanced setup menu provides sub-screens and functions for advanced configurations. The following sub- screen functions are included in the menu: LAN Configuration Display Configuration CPU Chipset Configuration ... -
Page 58: Figure 19: Bios Advanced Menu
KBox F-300-V1K - User Guide, Rev. 1.0 Figure 19: BIOS Advanced Menu BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit Onboard LAN1 Controller [Enabled] Onboard LAN2 Controller [Enabled] Onboard LAN3 Controller [Enabled] > Display Configuration > CPU Chipset Configuration >... -
Page 59: Figure 20: Bios Advanced Menu - Display Configuration
KBox F-300-V1K - User Guide, Rev. 1.0 Figure 20: BIOS Advanced Menu - Display Configuration BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit Display Configuration Integrated Graphics Controller [Enabled] → ←: Select Screen Primary Video Adaptor [Int Graphics (IGD)] ↑... -
Page 60: Figure 21: Bios Advanced Menu - - Cpu Chipset Configuration
KBox F-300-V1K - User Guide, Rev. 1.0 Figure 21: BIOS Advanced Menu -- - CPU Chipset Configuration BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit CPU Chipset Configuration SVM Mode [Enabled] → ←: Select Screen NX Mode [Enabled] ↑... -
Page 61: Figure 22: Bios Advanced Menu - - Nvme Configuration
KBox F-300-V1K - User Guide, Rev. 1.0 Figure 22: BIOS Advanced Menu -- - NVMe Configuration BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit NVMe Configuration No NVMe Device Found → ←: Select Screen ↑ ↓: Select Item Enter: Select +/-: Change Opt. -
Page 62: Figure 23: Bios Advanced Menu - - Sata Configuration
KBox F-300-V1K - User Guide, Rev. 1.0 Figure 23: BIOS Advanced Menu -- - SATA Configuration BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit SATA Configuration SATA Controller [Enabled] → ←: Select Screen ↑ ↓: Select Item Serial ATA Port-0* SanDisk SD8SBA (128.0GB) -
Page 63: Figure 24: Bios Advanced Menu - - Usb Configuration
KBox F-300-V1K - User Guide, Rev. 1.0 Figure 24: BIOS Advanced Menu -- - USB Configuration BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit USB Configuration USB Devices: → ←: Select Screen 1 Keyboard, 1 Hub ↑ ↓: Select Item... -
Page 64: Figure 25: Bios Advanced Menu - - Trusted Computing
KBox F-300-V1K - User Guide, Rev. 1.0 Figure 25: BIOS Advanced Menu -- - Trusted Computing BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit Configuration Security Device Support [Disable] NO Security Device → ←: Select Screen ↑ ↓: Select Item Enter: Select +/-: Change Opt. -
Page 65: Figure 26: Bios Advanced Menu - - Network Stack Configuration
KBox F-300-V1K - User Guide, Rev. 1.0 Figure 26: BIOS Advanced Menu -- - Network Stack Configuration BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit Network Stack Configuration Load Intel I211 / I210 UNDI [Disabled] → ←: Select Screen ↑... -
Page 66: Figure 27: Bios Advanced Menu - - Dio Configuration
KBox F-300-V1K - User Guide, Rev. 1.0 Figure 27: BIOS Advanced Menu -- - DIO Configuration BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit DIO Configuration User Configuration [Disabled] DIO_0* [Output High] DIO_1* [Output High] DIO_2* [Output High]... -
Page 67: Figure 28: Bios Advanced Menu - - Super Io Configuration
KBox F-300-V1K - User Guide, Rev. 1.0 Figure 28: BIOS Advanced Menu -- - Super IO Configuration BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit Super IO Configuration Serial Port UART Protection [No Protection] → ←: Select Screen >... -
Page 68: Figure 29: Bios Advanced Menu - - Super Io Configuration - - Serial Port 1 Configuration
KBox F-300-V1K - User Guide, Rev. 1.0 Figure 29: BIOS Advanced Menu -- - Super IO Configuration -- - Serial Port 1 Configuration BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit Super Port 1 Configuration Serial Port [Enabled] →... -
Page 69: Figure 30: Bios Advanced Menu - - Super Io Configuration - - Serial Port 2 Configuration
KBox F-300-V1K - User Guide, Rev. 1.0 Figure 30: BIOS Advanced Menu -- - Super IO Configuration -- - Serial Port 2 Configuration BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit Super Port 2 Configuration Serial Port [Enabled] →... -
Page 70: Figure 31: Bios Advanced Menu - - Super Io Configuration - - Serial Port 3 Configuration
KBox F-300-V1K - User Guide, Rev. 1.0 Figure 31: BIOS Advanced Menu -- - Super IO Configuration -- - Serial Port 3 Configuration BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit Super Port 3 Configuration Serial Port [Enabled] →... -
Page 71: Figure 32: Bios Advanced Menu - - Super Io Configuration - - Serial Port 4 Configuration
KBox F-300-V1K - User Guide, Rev. 1.0 Figure 32: BIOS Advanced Menu -- - Super IO Configuration -- - Serial Port 4 Configuration BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit Super Port 4 Configuration Serial Port [Enabled] →... -
Page 72: Figure 33: Bios Advanced Menu - - Super Io Configuration - - Serial Port 5 Configuration
KBox F-300-V1K - User Guide, Rev. 1.0 Figure 33: BIOS Advanced Menu -- - Super IO Configuration -- - Serial Port 5 Configuration BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit Super Port 5 Configuration Serial Port [Enabled] →... -
Page 73: Figure 34: Bios Advanced Menu - - Super Io Configuration - - Serial Port 6 Configuration
KBox F-300-V1K - User Guide, Rev. 1.0 Figure 34: BIOS Advanced Menu -- - Super IO Configuration -- - Serial Port 6 Configuration BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit Super Port 6 Configuration Serial Port [Enabled] →... -
Page 74: Figure 35: Bios Advanced Menu - - H/W Monitor
KBox F-300-V1K - User Guide, Rev. 1.0 Figure 35: BIOS Advanced Menu -- - H/W Monitor BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit PC Health Status CPU Temperature - TSI : +58 C CPU Temperature - Thermistor... -
Page 75: Power Setup Menu
KBox F-300-V1K - User Guide, Rev. 1.0 12.2.3. Power Setup Menu The Power setup menu provides functions and a sub-screen for power configurations. The following sub-screen function is included in the menu: WatchDog Timer Configuration Figure 36: BIOS Power Setup Menu... -
Page 76: Figure 37: Bios Power Setup Menu - - Watchdog Timer Configuration
KBox F-300-V1K - User Guide, Rev. 1.0 Feature Option Description ResumeLan I211-AT-2 [Disabled], [OS- Select whether to enable Wake from LAN Device Intel I211-AT-2. Driver], [FW- MagicPacket] ResumeLan I210-AT [Disabled], [OS- Select whether to enable Wake from LAN Device Intel I210-AT. -
Page 77: Boot Setup Menu
KBox F-300-V1K - User Guide, Rev. 1.0 12.2.4. Boot Setup Menu The boot setup menu lists the for boot device priority order, that is generated dynamically. Figure 38: BIOS Boot Setup Menu BIOS SETUP UTILITY Main Advanced Power Boot Security Save &... -
Page 78: Figure 39: Bios Boot Setup Menu - - Hard Drive Bbs Priorities
KBox F-300-V1K - User Guide, Rev. 1.0 Feature Option Description [Disabled] Figure 39: BIOS Boot Setup Menu -- - Hard Drive BBS Priorities BIOS SETUP UTILITY Main Advanced Power Boot Security Save & Exit Boot Option #1 [P0: SanDisk SD8SBAT128G1122] →... -
Page 79: Security Setup Menu
The Security setup menu provides information about the passwords and functions for specifying the security settings. The passwords are case-sensitive. The KBox F-300-V1K provides no factory-set passwords. If there is already a password installed, the system asks for this first. To clear a password, simply enter nothing and acknowledge by pressing <RETURN>. - Page 80 KBox F-300-V1K - User Guide, Rev. 1.0 12.2.5.1. Remember the password It is highly recommended to keep a record of all passwords in a safe place. Forgotten passwords results in being locked out of the system. If the system cannot be booted because the User Password or the Supervisor Password are not know, contact Kontron Support for further assistance.
-
Page 81: Save & Exit Setup Menu
KBox F-300-V1K - User Guide, Rev. 1.0 12.2.6. Save & Exit Setup Menu The exit setup menu provides functions for handling changes made to the UEFI BIOS settings and the exiting of the setup program. Figure 41: BIOS Save & Exit Setup Menu... -
Page 82: Appendix A: List Of Acronyms
KBox F-300-V1K - User Guide, Rev. 1.0 Appendix A: List of Acronyms The following table does not contain the complete acronyms used in signal names, signal type definitions or similar. A description of the signals is included in the I/O Connector and Internal connector chapters within this user guide. -
Page 83: About Kontron
KBox F-300-V1K - - User Guide, Rev. 1.0 About Kontron Kontron is a global leader in Embedded Computing Technology (ECT). As a part of technology group S&T, Kontron offers a combined portfolio of secure hardware, middleware and services for Internet of Things (IoT) and Industry 4.0 applications.