Light Patterns On Usb Recorders; Tips And Tricks; Getting Help - LogTag UTRIX-16 Product User Manual

Light Patterns on USB Recorders

Signal
Sequence of four quick alternate flashes of green
Wake-up signal
OK
Sequence of ten alternate flashes of green
Start signal
and red
Mark signal Sequence of five simultaneous flashes of green
Delay Signal
OK
Logging active, no alert
Single flash of green
present seconds (approx.)
Logging finished, no
Single flash of green
alert present seconds (approx.)
Logging active, alert
Single flash of red
condition present seconds
Logging finished, alert
Single flash of red
condition present seconds
Communication
The green
Sequence of simultaneous flashes of green
Initiate Stop
and red
Sequence of very quick simultaneous flashes of
Stopping
green
seconds
Two quick flashes of the green
Ready for USB
every second
Generating Files
The green
Ready for re-flash
The red

Tips and Tricks

Configuration
When configuring a USB recorder, allow enough time for the unit to
acclimatise to the target environment, particularly if you have
configured an upper alarm. This can be best achieved with a start
delay, or a date/time start if you know when the shipment takes
place.
Make sure you remove your UTRIX-16(M) from the USB socket when
you use a date/time start, so it starts at the time you want, rather
than when unplugged from the port.
During the trip
Always replace the USB protective cap before placing the UTRIX-16
(M) with the goods. While recording, make sure the UTRIX-16(M)'s
protective cap is facing down. The protection rating can only be
Page 10 of 16
Sequence
and red indicators
ALERT
indicators
ALERT
and red indicators
ALERT
indicator every 4
OK
indicator every 8
OK
indicator every 4
ALERT
indicator every 8
ALERT
indicator will flash occasionally
OK
indicators for 4 seconds
ALERT
and red indicators for 2
OK ALERT
OK
indicator is on permanently
OK
indicator is on permanently
ALERT
displayed after configuration has been successfully applied to the
l
UTRIX-16(M).
Not to be mixed up with...
displayed when the UTRIX-16(M) starts its recording cycle.
OK
l
The delay timer is re-started (followed by Delay Signal).
l
displayed when pressing
l
indicate an inspection mark in the software.
displayed directly after the start-up signal following a push button
l
start where a recording delay has been configured. In this instance
the start-up signal is repeated when the actual recording begins.
indicates UTRIX-16(M) is recording.
l
This is not displayed when pre-start is active and the main logging
cycle has not yet started. It is also not displayed when the green LED
has been turned off in the configuration screen.
indicates UTRIX-16(M) has finished recording.
l
This is not displayed when the green LED has been turned off in the
configuration screen.
Indicates UTRIX-16(M) is recording, an alert condition has occurred.
l
This is not displayed when pre-start recording has been configured
and the recorder has not yet been started.
indicates UTRIX-16(M) has finished recording and an alert condition
l
was present during the trip.
during USB communication the green LED will flash occasionally; no
l
additional information is conveyed in this.
This LED sequence appears when the stop sequence is initiated and
OK
l
requires that the
When this LED sequence starts, the
l
for the recorder to stop.
The UTRIX-16(M) is connected to a USB port and waiting for USB
indicator
l
communication.
The UTRIX-16(M) is generating files. No USB activity will be
l
observed on the computer screen during this time.
The UTRIX-16(M) is ready to receive new firmware. Special software
l
is required to upload new firmware to the UTRIX-16(M).
achieved when used in this orientation. For applications requiring a
higher IP rating the unit should be used in the protective case,
available as an accessory.

Getting help

If after studying this Product User Guide and the relevant Quick Start
Guide you still need further information, please visit the support
section of the LogTag
http://www.logtagrecorders.com/support/support.html .
UTRIX-16(M) Product User Guide, Revision 2.0, copyright © 2004-2016,
Occurrence
button while recording to
START/Mark
button is enabled.
STOP
button must be released
STOP
®
Recorders website at
LogTag
®
Recorders . All rights reserved.