Advertisement

Quick Links

UM2335
User manual
EVB-LIV3F / EVB-LIV3R Evaluation board
Introduction
EVB-LIV3x evaluation board is a complete standalone evaluation platform for
Teseo-LIV3x Tiny GNSS module.
Teseo-LIV3x module is an easy to use Global Navigation Satellite System (GNSS)
standalone module, embedding Teseo III single die standalone positioning receiver
IC working simultaneously on multiple constellations (GPS/Galileo/Glonass/
BeiDou/QZSS).
EVB-LIV3F is designed for top performance Teseo-LIV3F GNSS module.
EVB-LIV3R is designed for top performance Teseo-LIV3R GNSS ROM module.
December 2019
UM2335 Rev 2
1/20
www.st.com
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the UM2335 and is the answer not in the manual?

Questions and answers

Summary of Contents for ST UM2335

  • Page 1 Teseo III single die standalone positioning receiver IC working simultaneously on multiple constellations (GPS/Galileo/Glonass/ BeiDou/QZSS). EVB-LIV3F is designed for top performance Teseo-LIV3F GNSS module. EVB-LIV3R is designed for top performance Teseo-LIV3R GNSS ROM module. December 2019 UM2335 Rev 2 1/20 www.st.com...
  • Page 2: Table Of Contents

    Revision history ......... . . 19 2/20 UM2335 Rev 2...
  • Page 3 Document revision history ..........19 UM2335 Rev 2...
  • Page 4 Block diagram ............18 4/20 UM2335 Rev 2...
  • Page 5: Features

     Internal backup battery placing (battery not provided)  Push buttons to switch ON and OFF  Current measurement connector  Reset button  UART by USB connector  I2C slave connector  PPS output LED  Power output LED UM2335 Rev 2 5/20...
  • Page 6: Evb-Liv3X General Presentation

    EVB-LIV3x general presentation UM2335 EVB-LIV3x general presentation EVB-LIV3x kit is composed of several elements:  EVB-LIV3x evaluation board  GNSS active antenna  1 USB cable 6/20 UM2335 Rev 2...
  • Page 7: Interfaces

    LED turns on. When the ON/OFF switch is lifted, VBAT is connected to GND, the board is switched OFF. Reset A reset button (Figure 3) is present on the front case panel and it resets the Teseo-LIV3x module. UM2335 Rev 2 7/20...
  • Page 8: Led Indicators

     The PPS Green LED (Figure 5) indicator blinking every second indicates that Teseo- LIV3x is up and running; Figure 5. PPS LED indicator UART by USB UART interface (Figure 6) is provided via USB connector. 8/20 UM2335 Rev 2...
  • Page 9: I2C Interface

    Table 1. EVB-LIV3x – UART Configuration Parameters Baud rate Data Bits Stop Bits Parity Handshake 9600 Baud 8 Bits 1 Bit none none I2C interface The 4-pin connector (CN302) provides I2C bus signal and power supply as shown in Figure UM2335 Rev 2 9/20...
  • Page 10: Gnss Input Antenna

    Passive or active antenna can be used on EVB-LIV3x. The DC power supply for active antenna is 3V3 with current limitation in case of short circuit. Note: Please use a DC blocker for passive or simulator connected to EVB-LIV3x. 10/20 UM2335 Rev 2...
  • Page 11: Current Measurement Connector

    EVB-LIV3x provides a connector (Figure 10) to evaluate current consumption. Figure 10. Current measurement connector Table 3. Current measurement connector pin description Connector Signal Comment power supply Vcc measure point VBATT power supply Vbatt measure point UM2335 Rev 2 11/20...
  • Page 12: Current Measurement Process

    Perform steps 1, 2 and 3 Note: The acquisition current will vary based on the number of constellations you have configured the firmware to acquire, so please take note of that when taking and comparing measurements. 12/20 UM2335 Rev 2...
  • Page 13: Teseo Suite Connection

    If the “Configuration Session” panel is not opened, two ways either can be followed as Figure 13 shown in Go to the "File" menu and select "New Session" Click the "Edit Session Configuration" button. Figure 13. Edit Session Configuration button UM2335 Rev 2 13/20...
  • Page 14: Add/Delete Device

    Set the hardware type ‘STA8090’ value. Select the Control port and choose the parameters of the serial connection as in Table 1 On the Control port, the user can select the NMEA protocol Press the “OK” button to create the device. 14/20 UM2335 Rev 2...
  • Page 15: Figure 14. Configuration Device Panel

    Please note that the protocol of the device and its name cannot be changed once the “OK” button has been clicked. To delete a device from the session, press the corresponding delete button in the “Delete Device” column from the "Configuration Session" form. UM2335 Rev 2 15/20...
  • Page 16: Connect Or Disconnect Control Port

    Click the “Connect” (Electrical Plug) button to open the selected ports, and a red X shows up, as shown in Figure 16 below. Figure 16. Port connections active Open the NMEA output window to confirm the proper NMEA output using the button shown Figure 16/20 UM2335 Rev 2...
  • Page 17: Figure 17. Nmea Output View

    Teseo Suite connection Figure 17. NMEA output view On NMEA panel view the NMEA stream coming from EVB-LIV3x can be seen as shown in Figure Figure 18. NMEA view panel Now your EVB-LIV3x is fully working. UM2335 Rev 2 17/20...
  • Page 18: Board General View

    J302 : 2-3 : no use of VCC_RF to optimize Teseo-LIV3x current J303 : 2-3 : VCC_IO=3.3V J400 : 2-3 : same reason as J302 J500 : 1-2 : use 2.1V to supply Teseo-LIV3x in order to optimize current consumption Block diagram overview Figure 19. Block diagram 18/20 UM2335 Rev 2...
  • Page 19: Revision History

    UM2335 Revision history Revision history Table 4. Document revision history Date Revision Changes 28-Mar-2018 Initial release. 05-Dec-2019 Minor text changes. UM2335 Rev 2 19/20...
  • Page 20 ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement.

This manual is also suitable for:

Evb-liv3fEvb-liv3r

Table of Contents